KROHNE SHD 200 User manual

Control unit for 4…20 mA/HART® field devices
Electronic Revision: ER 2.0.X
SHD 200 Handbook
© KROHNE 07/2022 - 4007792904 - MA SHD 200 R04 en
The documentation is only complete when used in combination with the relevant
documentation for the sensor.

All rights reserved. It is prohibited to reproduce this documentation, or any part thereof, without
the prior written authorisation of KROHNE Messtechnik GmbH.
Subject to change without notice.
2
SHD 200
www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
Copyright 2022 by
KROHNE Messtechnik GmbH - Ludwig-Krohne-Str. 5 - 47058 Duisburg (Germany)
: IMPRINT :::::::::::::::::::::::::::::::::::::::

CONTENTS
3
www.krohne.com07/2022 - 4007792904 - MA SHD 200 R04 en
SHD 200
1 Safety instructions 5
1.1 Certifications .................................................................................................................... 5
1.2 Software history ............................................................................................................... 6
1.3 Intended use ..................................................................................................................... 7
1.4 Safety instructions from the manufacturer ..................................................................... 7
1.4.1 Copyright and data protection ................................................................................................ 7
1.4.2 Disclaimer ............................................................................................................................... 8
1.4.3 Product liability and warranty ................................................................................................ 9
1.4.4 Information concerning the documentation........................................................................... 9
1.4.5 Warnings and symbols used................................................................................................. 10
1.5 Safety instructions for the operator............................................................................... 10
2 Device description 11
2.1 Scope of delivery............................................................................................................. 11
2.2 Device description .......................................................................................................... 12
2.3 Nameplate ...................................................................................................................... 13
3 Installation 14
3.1 General notes on installation......................................................................................... 14
3.2 Storage and transport .................................................................................................... 14
3.3 Point-to-Point connection - analogue / digital mode .................................................... 15
3.4 Pre-installation requirements ....................................................................................... 16
3.5 Opening the housing....................................................................................................... 17
3.6 Wall mounting ................................................................................................................ 19
3.6.1 Plastic housing...................................................................................................................... 19
3.6.2 Aluminium housing............................................................................................................... 20
4 Electrical connections 21
4.1 Safety instructions.......................................................................................................... 21
4.2 Important device-specific notes on electrical connection............................................. 21
4.3 Connection diagram overview........................................................................................ 22
4.4 Connecting the field device cable .................................................................................. 24
4.5 Connecting the second current output .......................................................................... 25
4.6 Connecting the relay outputs ......................................................................................... 26
4.7 Connecting the external HART adapter ......................................................................... 27
4.8 Power supply .................................................................................................................. 28
4.9 Connecting the SHD 200 for use in an active 4...20 mA current output ........................ 29
5 Start-up 31
5.1 Start-up........................................................................................................................... 31

CONTENTS
4 www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
SHD 200
6 Operation 33
6.1 Operating elements........................................................................................................ 33
6.2 Menu mode ..................................................................................................................... 34
6.2.1 Menu mode structure ........................................................................................................... 34
6.2.2 Status messages and diagnostic information ...................................................................... 36
6.3 Function tables............................................................................................................... 41
6.4 Setup............................................................................................................................... 63
6.4.1 Configuration of measurement page.................................................................................... 63
6.4.2 Number format ..................................................................................................................... 68
6.4.3 Configuration of loop 1.......................................................................................................... 68
6.4.4 Configuration of loop 2.......................................................................................................... 68
6.4.5 Function of relay 1 + 2........................................................................................................... 69
6.4.6 Configuration of relay 1+2..................................................................................................... 71
6.4.7 Illumination setting............................................................................................................... 77
6.4.8 Overflow sign and exponential format.................................................................................. 78
6.5 Commissioning of OPTIWAVE level transmitters .......................................................... 79
6.6 Commissioning of OPTIBAR pressure transmitters...................................................... 80
7 Service 82
7.1 Maintenance and repair ................................................................................................. 82
7.2 Spare parts availability................................................................................................... 82
7.3 Availability of services .................................................................................................... 82
7.4 Returning the device to the manufacturer..................................................................... 82
7.4.1 General information.............................................................................................................. 82
7.4.2 Form (for copying) to accompany a returned device............................................................ 83
7.5 Disposal .......................................................................................................................... 83
7.5.1 Disassembly and recycling ................................................................................................... 84
8 Technical data 87
8.1 Technical data................................................................................................................. 87
8.2 Dimensions..................................................................................................................... 89
9 Notes 91

SAFETY INSTRUCTIONS 1
5
SHD 200
www.krohne.com07/2022 - 4007792904 - MA SHD 200 R04 en
1.1 Certifications
The device meets the essential requirements of the EU directives. The CE marking indicates the
conformity of the product with the union legislation applying to the product and providing for CE
marking.
For full information of the EU directives and standards and the approved certifications, please
refer to the EU declaration on the KROHNE website.
Hazardous areas
•ATEX II 2 G Ex ia IIC T4 Gb
IECEx ia IIC T4 Gb
QPS Ex ia IIC T4 Gb / Class I, Zone 1 AEx ia IIC T4 Gb
UKEX II 2 G Ex ia IIC T4 Gb
Other approvals and standards
•NAMUR recommendation NE 6, NE 21, NE 43, NE 53, NE 107
•Shock resistance IEC 60721-3-4 class 4M4
•Vibration resistance IEC 60721-3-4 class 4M4
•Vibration resistance IEC 61298-3 low vibration control room
CE marking

1 SAFETY INSTRUCTIONS
6
SHD 200
www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
1.2 Software history
Changes and effect on compatibility
INFORMATION!
In the table below, "_" is a placeholder for possible multi-digit alphanumeric combinations,
depending on the available version.
1 Downwards compatible changes and fault repair with no effect on operation (e.g. spelling
mistakes on display)
2-_ Downwards compatible hardware and/or software change of interfaces:
HHART®
P PROFIBUS
F Foundation Fieldbus
M Modbus
X all interfaces
3-_ Downwards compatible hardware and/or software change of inputs and outputs:
I Current output
F, P Frequency / pulse output
S Status output
C Control input
CI Current input
X all inputs and outputs
4 Downwards compatible changes with new functions
5 Incompatible changes, i.e. electronic equipment must be changed.
Release date Electronic
revision
Changes and
compatibility
Documentation
10/2019 ER 1.0.0_ MA SHD 200 R01
01/2020 ER 1.0.1_ 1 MA SHD 200 R02
05/2020 ER 1.0.2 1 MA SHD 200 R03
03/2022 ER 2.0.X 5 MA SHD 200 R04

SAFETY INSTRUCTIONS 1
7
SHD 200
www.krohne.com07/2022 - 4007792904 - MA SHD 200 R04 en
1.3 Intended use
The SHD 200 is a control unit for 4...20 mA/HART® field devices. The intended use is process
control by using the relays, the second current output and the NAMUR NE 107 signalisation by
LEDs for the HART® parameters of the connected field device. The device has been constructed
for indoor and outdoor use below the maximum altitude of 2000 m / 6562 ft.
1.4 Safety instructions from the manufacturer
1.4.1 Copyright and data protection
The contents of this document have been created with great care. Nevertheless, we provide no
guarantee that the contents are correct, complete or up-to-date.
The contents and works in this document are subject to copyright. Contributions from third
parties are identified as such. Reproduction, processing, dissemination and any type of use
beyond what is permitted under copyright requires written authorisation from the respective
author and/or the manufacturer.
The manufacturer tries always to observe the copyrights of others, and to draw on works created
in-house or works in the public domain.
DANGER!
For devices used in hazardous areas, additional safety notes apply; please refer to the Ex
documentation.
CAUTION!
Responsibility for the use of the measuring devices with regard to suitability, intended use and
corrosion resistance of the used materials against the measured fluid lies solely with the
operator.
WARNING!
If the device is not used according to the operating conditions (refer to chapter "Technical data"),
the intended protection could be affected.
INFORMATION!
This device is a Group 1, Class A device as specified within CISPR11. It is intended for use in
industrial environment. There may be potential difficulties in ensuring electromagnetic
compatibility in other environments, due to conducted as well as radiated disturbances.
INFORMATION!
The manufacturer is not liable for any damage resulting from improper use or use for other than
the intended purpose.

1 SAFETY INSTRUCTIONS
8
SHD 200
www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
The collection of personal data (such as names, street addresses or e-mail addresses) in the
manufacturer's documents is always on a voluntary basis whenever possible. Whenever
feasible, it is always possible to make use of the offerings and services without providing any
personal data.
We draw your attention to the fact that data transmission over the Internet (e.g. when
communicating by e-mail) may involve gaps in security. It is not possible to protect such data
completely against access by third parties.
We hereby expressly prohibit the use of the contact data published as part of our duty to publish
an imprint for the purpose of sending us any advertising or informational materials that we have
not expressly requested.
1.4.2 Disclaimer
The manufacturer will not be liable for any damage of any kind by using its product, including,
but not limited to direct, indirect or incidental and consequential damages.
This disclaimer does not apply in case the manufacturer has acted on purpose or with gross
negligence. In the event any applicable law does not allow such limitations on implied warranties
or the exclusion of limitation of certain damages, you may, if such law applies to you, not be
subject to some or all of the above disclaimer, exclusions or limitations.
Any product purchased from the manufacturer is warranted in accordance with the relevant
product documentation and our Terms and Conditions of Sale.
The manufacturer reserves the right to alter the content of its documents, including this
disclaimer in any way, at any time, for any reason, without prior notification, and will not be liable
in any way for possible consequences of such changes.

SAFETY INSTRUCTIONS 1
9
SHD 200
www.krohne.com07/2022 - 4007792904 - MA SHD 200 R04 en
1.4.3 Product liability and warranty
The operator shall bear responsibility for the suitability of the device for the specific purpose.
The manufacturer accepts no liability for the consequences of misuse by the operator.
Improper installation or operation of the devices (systems) will cause the warranty to be void.
The respective "Standard Terms and Conditions" which form the basis for the sales contract
shall also apply.
1.4.4 Information concerning the documentation
To prevent any injury to the user or damage to the device it is essential that you read the
information in this document and observe applicable national standards, safety requirements
and accident prevention regulations.
If this document is not in your native language and if you have any problems understanding the
text, we advise you to contact your local office for assistance. The manufacturer cannot accept
responsibility for any damage or injury caused by misunderstanding of the information in this
document.
This document is provided to help you establish operating conditions, which will permit safe and
efficient use of this device. Special considerations and precautions are also described in the
document, which appear in the form of icons as shown below.

1 SAFETY INSTRUCTIONS
10
SHD 200
www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
1.4.5 Warnings and symbols used
Safety warnings are indicated by the following symbols.
• HANDLING
This symbol designates all instructions for actions to be carried out by the operator in the
specified sequence.
iRESULT
This symbol refers to all important consequences of the previous actions.
1.5 Safety instructions for the operator
DANGER!
This warning refers to the immediate danger when working with electricity.
DANGER!
This warning refers to the immediate danger of burns caused by heat or hot surfaces.
DANGER!
This warning refers to the immediate danger when using this device in a hazardous atmosphere.
DANGER!
These warnings must be observed without fail. Even partial disregard of this warning can lead to
serious health problems and even death. There is also the risk of seriously damaging the device
or parts of the operator's plant.
WARNING!
Disregarding this safety warning, even if only in part, poses the risk of serious health problems.
There is also the risk of damaging the device or parts of the operator's plant.
CAUTION!
Disregarding these instructions can result in damage to the device or to parts of the operator's
plant.
INFORMATION!
These instructions contain important information for the handling of the device.
LEGAL NOTICE!
This note contains information on statutory directives and standards.
WARNING!
In general, devices from the manufacturer may only be installed, commissioned, operated and
maintained by properly trained and authorized personnel.
This document is provided to help you establish operating conditions, which will permit safe and
efficient use of this device.

DEVICE DESCRIPTION 2
11
SHD 200
www.krohne.com07/2022 - 4007792904 - MA SHD 200 R04 en
2.1 Scope of delivery
Optional accessories
•External HART® adapter
•Weather protection cover
•Wall mounting brackets
INFORMATION!
Inspect the packaging carefully for damages or signs of rough handling. Report damage to the
carrier and to the local office of the manufacturer.
INFORMATION!
Do a check of the packing list to make sure that you have all the elements given in the order.
INFORMATION!
Look at the device nameplate to ensure that the device is delivered according to your order.
Check for the correct supply voltage printed on the nameplate.
Figure 2-1: Example of the standard scope of delivery
1 Ordered device
2 Documentation

2 DEVICE DESCRIPTION
12
SHD 200
www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
2.2 Device description
This 2-wire device can be connected to field devices with HART® protocol or 4…20 mA current
output. The two free programmable relays and the second current output allow process control.
Different customer-specific measurement pages with up to 4 displayed values enable a detailed
monitoring of the process. By using the second current output it is possible to use the backlight
and high brightness LEDs for NAMUR NE 107 status signalisation. A HART® access to the field
device is possible by connecting a HART® Handheld or HART® Modem to the internal or optional
external HART® adapter.
For Krohne level and pressure field devices, several functions are available to perform the
commissioning directly via the SHD 200.
Figure 2-2: Device description
1 Display
2 Operation keys
3 Cable glands
4 High-brightness LEDs for NAMUR NE 107 status signalisation

DEVICE DESCRIPTION 2
13
SHD 200
www.krohne.com07/2022 - 4007792904 - MA SHD 200 R04 en
2.3 Nameplate
INFORMATION!
Look at the device nameplate to ensure that the device is delivered according to your order.
Check for the correct supply voltage printed on the nameplate.
Figure 2-3: Example of a nameplate
1 Manufacturer
2 Device name
3 CE marking
4 TAG number
5 Data matrix code (serial number),
Observe the operation and installation instruction, Ingress protection
China RoHS,
Electronic / Electric device waste marking,
6 Power supply data,
Parameter of measuring unit
7 Order code,
Manufacturing date,
Internet address of manufacturer
8 Electronic revision,
Serial number
9 Production order
SHD 200
IP66/67
LOOP 1: Ui=30V Ii=120mA Pi=1W Ci=45nF Li=0
LOOP 2: Ui=30V Ii=120mA Pi=1W Ci=25nF Li=0
RELAY: Ui=30V Ii=30mA Pi=100mW Ci=15nF Li=0
VGSH

3 INSTALLATION
14
SHD 200
www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
3.1 General notes on installation
3.2 Storage and transport
INFORMATION!
Inspect the packaging carefully for damages or signs of rough handling. Report damage to the
carrier and to the local office of the manufacturer.
INFORMATION!
Do a check of the packing list to make sure that you have all the elements given in the order.
INFORMATION!
Look at the device nameplate to ensure that the device is delivered according to your order.
Check for the correct supply voltage printed on the nameplate.
CAUTION!
Do not make any mechanical modifications to the device. This can result in the loss of proper
functionality, as well as the rights under the device warranty.
• Store and transport the device in a dry, dust-free environment.
• Store and transport the device in an environment with a temperature between -30...+70°C /
-22...+158°F.
• The original packing is designed to protect the equipment. It has to be used if the device is
transported or sent back to the manufacturer to prevent damage of the device.

INSTALLATION 3
15
SHD 200
www.krohne.com07/2022 - 4007792904 - MA SHD 200 R04 en
3.3 Point-to-Point connection - analogue / digital mode
Point-to-Point connection between the field device and the HART® Master.
The current output of the field device is passive.
If using more than one HART® master please be aware of the correct configuration because only
one Primary master and one Secondary master are allowed. Two Primary masters or two
Secondary masters will cause communication errors.
Default master modes are
•SHD 200: Secondary
•HART® modem in PACTware: Primary
•HART® Field Communicator: Secondary (can’t be changed in most devices)
Figure 3-1: Overview point-to-point connection
1 HART® master with e.g. PACTwareTM FDT/DTM
2 HART® modem
3 HART® signal
4 SHD 200
5 HART® master with HART® DD (for example field communicator)
6 HART® field device
7 Power supply for devices (slaves) with passive current output
8 Load 250  (Ohm) (only required if not used in SHD 200)

3 INSTALLATION
16
SHD 200
www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
These default master modes lead to the following use cases:
If you
•parameterise or calibrate your field device using PACTware with a HART® modem, the
master mode of the SHD 200 should be "Secondary"
•parameterise or calibrate your field device with a HART® field communicator, the master
mode of the SHD 200 should be "Primary"
•use PACTware with a HART® modem and a HART® field communicator at the same time, the
HART® functionality of the SHD 200 must be deactivated
•use a HART® PLC, find out its master mode and adapt the master mode of the SHD 200
appropriate
3.4 Pre-installation requirements
CAUTION!
Always note the following items to ensure a proper and safe installation:
• Make sure that there is adequate space to the sides.
• Protect the device from direct sunlight.
• The device installed in control cabinets require adequate cooling, e.g. by fan or heat
exchanger.
• Do not expose the device to intense vibration.
• Use assembly materials and tools in compliance with the applicable occupational health and
safety directives (assembly materials and tools are not part of the scope of delivery).
• Do not make any mechanical modifications to the device. This can result in the loss of proper
functionality, as well as the rights under the device warranty.
• The device must not be heated by radiated heat (e.g. exposure to the sun) to a electronics
housing surface temperature above the maximum permissible ambient temperature. If it is
necessary to prevent damage from heat sources, a heat protection (e.g. sun shade) has to be
installed.
CAUTION!
The device must be suitable for the temperature specified (including chemical resistance).
INFORMATION!
Assembly materials and tools are not part of the delivery. Use the assembly materials and tools
in compliance with the applicable occupational health and safety directives.

INSTALLATION 3
17
SHD 200
www.krohne.com07/2022 - 4007792904 - MA SHD 200 R04 en
3.5 Opening the housing
All installation works on the electrical connections and mounting require to open the housing:
• Put a small flat tool (e.g. screwdriver) into the right hinge lock and open the device 1.
• Lift up the housing 2.
iNow you have access to the electronic compartment and the possibility to mount the device
on a wall.
INFORMATION!
Clean and grease all threads each time you open the housing. Use only resin-free and acid-free
grease. Before closing the cover, ensure that the housing gasket is properly fitted, clean and
undamaged.
Opening the plastic housing
Figure 3-2: Opening the plastic housing

3 INSTALLATION
18
SHD 200
www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
• Pull only the right hinge lock the side 1.
• Loosen the 2 torx screws (TX20) with a torx screwdriver 2.
• Lift up the housing 3.
iNow you have access to the electronic compartment and the possibility to mount the device
on a wall.
• For closing the housing again, use the 2 torx screws with a torque of 1,5 Nm.
Opening the aluminium housing
Figure 3-3: Opening the aluminium housing

INSTALLATION 3
19
SHD 200
www.krohne.com07/2022 - 4007792904 - MA SHD 200 R04 en
3.6 Wall mounting
3.6.1 Plastic housing
1 Mark the holes with a suitable pen 1.
2 Drill the 4 holes and fasten the device securely to the wall 2.
CAUTION!
Always note the following items to ensure a proper and safe installation:
• Make sure that there is adequate space to the sides.
• The device must not be heated by radiated heat (e.g. exposure to the sun) to a electronics
housing surface temperature above the maximum permissible ambient temperature. If it is
necessary to prevent damage from heat sources, a heat protection (e.g. sun shade) has to be
installed.
• Units installed in control cabinets require adequate cooling, e.g. by fan or heat exchanger.
• Do not expose the unit to intense vibration.
• Use assembly materials and tools in compliance with the applicable occupational health and
safety directives (assembly materials and tools are not part of the scope of delivery).
CAUTION!
Installation, assembly, start-up and maintenance may only be performed by appropriately
trained personnel. The regional occupational health and safety directives must always be
observed.
INFORMATION!
A mounting system with a minimum load force of 0.1 kN (for example FISCHER type UX10)
suitable for the background has to be applied.
Figure 3-4: Wall mounting of the plastic housing
INFORMATION!
For outdoor mounting, we recommend the optional weather protection cover XGSH010000 for
wall and pipe mounting. For more flexibility and convenient mounting, we recommend wall
mounting brackets XGSH010020 for plastic housing.

3 INSTALLATION
20
SHD 200
www.krohne.com 07/2022 - 4007792904 - MA SHD 200 R04 en
3.6.2 Aluminium housing
1 Mark the holes with a suitable pen 1.
2 Drill the 4 holes and fasten the device securely to the wall 2.
Figure 3-5: Wall mounting of the aluminium housing
INFORMATION!
For outdoor mounting, we recommend the optional weather protection cover XGSH010000 for
wall and pipe mounting. For more flexibility and convenient mounting, we recommend wall
mounting brackets XGSH010030 for aluminium housing.