KT&C KPC-N570 User manual

HIGH PERFORMANCE
Super Night Vision Camera
OPERATION MANUAL
Thank you for choosing our high quality camera.
Before attempting to connect or operate, please read and follow
these instructions.
M083-N570-001
OPERATION MANUAL

CONTENTS
1. CAUTIONS
2. FEATURES
3. COMPONENTS
4. NAME AND FUNCTION
5. INSTALLATION
6. DIMENSIONS
7. SPECIFICATION
8. OSD MANUAL
3

1. CAUTIONS
4
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions;
1. This device may not cause harmful interference.
2. This device must accept any interference received, including
interference that may cause undesired operation.
1. A regulated DC12V 3A power supply is recommended for use with this camera
for the best picture and the most stable operation.
An unregulated power supply can cause damage to the camera.
When unregulated power supply is applied, product warranty will be
out of subject.
2. It is recommended that the camera is used with a monitor that has a CCTV quality
75 video impedance level.
If your monitor is switched to high impedance then please adjust accordingly.
3. Do not attempt to disassemble the camera to gain access to the internal componets.
Refer servicing to your dealer.
4. Never face the camera towards the sun or any bright or reective light, which may
cause smear on the picture and possible damage to the CCD.
5. Do not remove the serial sticker for the warranty service.
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.”
Note-
Any changes or modifications in construction of this device
which are not expressly approved by the party responsible
for compliance could void the user’s authority to operate the
equipment.
Caution -
This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be
required to take adequate measures.
WARNING -

1. CAUTIONS
5
Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with
separate collection systems)
This marking shown on the product or its literature, indicate that it should not
be disposed with other household wastes at the end of its working life. To
prevent possible harm to the environment or human health from uncontrolled
waste disposal, please separate this from other types of wastes and recycle it
responsibly to promote the sustainable reuse of material resources.
This product should not be mixed with other commercial wastes purchased this
product, or their local government ofce, for details of where and how they can
take item for environmentally safe recycling.
Business users should contact their supplier and check the terms and
conditions of the purchase contract.
Household users should contact either the retailer where they for disposal.

2. FEATURES
• 1/3" 410K/470K Sony Super-HAD CCDⅡ
Minimum illumination 0.1 Lux (F2.0, 30 IRE, Sense-Up Off)
S/N Ratio 50 dB
• High Resolution 580TV Lines
This camera has realized high resolution of 580TV lines using the top-notch full
digital image processing, 10 Bit A/D serial signal processing and special algorithm
technologies.
• 3D DNR (3D Digital Noise Reduction)
The DNR technology eliminates noise thus generating a distinct and clear image.
This camera DNR function utilizes an adaptive 3D Filter reducing noise caused by
movement.
• DAY&NIGHT
This camera has the DayNight function.
Day&Night operation feature an ‘auto’ mode which switches between day and night
mode automatically based upon the level of illumination on the scene.
And also, the COLOR mode operates in daytime conditions to provide optimum colors,
and B/W mode operates in night-time conditions to enhance the denition of the
image.
• Privacy Mask Function
Privacy masking allows for the ‘blanking’ of specic areas of a scene, where the viewing
or recording of images is prohibited or undesired.
• OSD (On Screen Display)
This camera can easily controlled by multi-language OSD function on the monitor
screen.
6

3. COMPONENTS
SUPER NIGHT VISION
CAMERA
VIDEO OUTPUT
TEST CABLE
L-WRENCH,
SCREW - 3ea
OPERATION MANUAL
7

8
4. NAME AND FUNCTION
① Sunshield Fixing Bolt
② Sunshield
③ Mounting Bracket
④ IR Illuminator
LED : Left(35ea), Right(35ea)
⑤ Photo cell
⑥ Body
⑦ Body Fixing Ring
①
⑤ ④④ ④
③
⑥
③ ②
Back
Cable Concealed Thru Bracket
⑦

5. INSTALLATION
• MOUNTING POSITION
9
360°
90°
15°
* 1st Axis * 2nd Axis
* 3rd Axis
360°

10
5. INSTALLATION
• MONITOR CONNECTION
(1) DC12V
(2) DUAL(DC12V/AC24V)
DC12V
BNC FEMALE
DC12V POWER SUPPLY
VIDEO IN
DC12V/AC24V
BNC FEMALE
DC12V /AC24VPOWER SUPPLY
VIDEO IN
When you install the camera, please glue up the end of cable to
keep it stable in order to protect the camera from the humidity problems.

6. DIMENSIONS
11
79.2
77.9
106.4
Ø60
175.5
145
129.4
263.4
135 125
Ø80
M12XP1

12
7. SPECIFICATION
Signal Format NTSC PAL
Image Device 1/3" Sony Super HAD CCDⅡ
Total Pixels 811(H) x 508(V) 795(H) x 596(V)
Effective Pixels 768(H) x 494(V) 752(H) x 582(V)
Inter. H/V 15,734/KHz(H), 59.94Hz(V) 15,625KHz(H), 50Hz(V)
H.Resolution More than 580TV Lines
Minimum illumination 0.1Lux / F2.0
S/N Ratio More than 50dB (AGC Off)
Sync System Internal
Gamma r=0.05 ~1.0 Adjustable / USER
Video Output 1.0 Vp-p Composite(75Ω)
Lens Varifocal
Electronic Shutter 1/60 sec 1/50 sec
Manual Shutter 1/60(50), FLK, 1/250, 1/500, 1/2K, 1/5K, 1/10K, 1/100K
X2, X4, X8, X16, X32, X64, X128, X256
Sense-up Off / Auto (X2, X4, X8, X16, X32, X64, X128, X256)
AGC Off / Low / Middle / High
BLC Off / BLC / HSBLC
White Balance ATW / PUSH / PUSH-LOCK / MANUAL / Indoor / Outdoor
Day&Night True Day & Night With ICR Mechanism
Motion Detection Zone 4ea(Mask On / Off)
Privacy Zone Zone 8ea(Mask On / Off)
3-DNR Off / On(0~100 Level Adjustable)
D-WDR Off / Indoor / Outdoor
Image Freeze / Mirror / D-zoom / Sharpness / Color gain / Gamma / NEG.Image
OSD Available
Language Option1: English, French, Russian, German, Spanish,Dutch
Option2: English, Chinese
IR LED 850nm, 70ea, Up to 50m
IR LED Operation On: 1Lux, Off: 3Lux
IP Rating IP66(Weatherproof)
Operating Temperature 14˚F~122˚F(-10˚C ~ +50˚C)
Storage Temperature -4˚F~140˚F(-20˚C ~ +60˚C)
Input Power
Source
DC12V DC12V ±10% Max 1.2A
DUAL AC24V ±10% Max 12.5W, DC12V ±10% Max 1.2A
Weight Approx. 1200g
Option DUAL(AC24V/DC12V)

13
8. OSD MANUAL
GENERAL STRUCTURE
SETUP MENU
LENS •BRIGHTNESS •RETURN
EXPOSURE •SHUTTER •BRIGHTNESS •AGC
•SENSE-UP •BLC •D-WDR
•RETURN
WHITE BAL •ATW •PUSH •PUSH-LOCK
•MANUAL •INDOOR •OUTDOOR
DAY&NIGHT •COLOR •B/W •AUTO
IMAGE •FREEZE •MIRROR •D-ZOOM
•SHARPNESS •COLOR GAIN
•GAMMA •NEG.IMAGE •RETURN
3DNR •LEVEL •RETURN
SPECIAL •CAM TITLE •LANGUAGE
•MOTION •PRIVACY •SYNC
•RETURN
RESET
EXIT

14
8. OSD MANUAL
LENS MENU STRUCTURE
EXPOSURE MENU STRUCTURE
LENS →DC →BRIGHT →1~100
↕
EXPOSURE
↕
WHITE BAL
↕
DAY NIGHT
↕
IMAGE
↕
3DNR
↕
SPECIAL
↕
RESET
↕
EXIT
LENS SHUTTER →X256 ~1/100K
↕ ↕
EXPOSURE →AGC →LOW, MIDDLE, HIGH
↕ ↕
WHITE BAL SENSE-UP →X2 ~ X256
↕ ↕ GAIN, LEFT/RIGHT, WIDTH,
TOP/BOTTOM, HEIGNT
DAY NIGHT BLC →BLC →
↕ ↕
IMAGE ↕HSBLC →LEVEL, LEFT/RIGHT, WIDTH,
TOP/BOTTOM, HEIGNT
↕
3DNR D-WDR →INDOOR, OUTDOOR
↕
SPECIAL
↕
RESET
↕
EXIT

15
8. OSD MANUAL
WHITE BALANCE MENU STRUCTURE
DAY & NIGHT MENU STRUCTURE
LENS
↕
EXPOSURE
↕
WHITE BAL →ATW
↕ ↕
DAY NIGHT PUSH
↕ ↕
IMAGE P-LOCK
↕ ↕
3DNR MANUAL →BLUE 1~ 100
↕ ↕ ↕
SPECIAL INDOOR RED 1~ 100
↕ ↕
RESET OUTDOOR
↕
EXIT
LENS
↕
EXPOSURE
↕
WHITE BAL
↕
DAY NIGHT →AUTO
↕ ↕
IMAGE B/W →BURST →ON / OFF
↕ ↕
3DNR COLOR
↕
SPECIAL
↕
RESET
↕
EXIT

16
8. OSD MANUAL
IMAGE MENU STRUCTURE
3DNR MENU STRUCTURE
LENS FREEZE →ON/OFF
↕ ↕
EXPOSURE MIRROR →MIRROR ↔V-FLIP ↔ROATE
↕ ↕
WHITE BAL D-ZOOM →x1 ~ x32 ↔PAN -100~100 ↔TILT -100~100
↕ ↕
DAY NIGHT SHARPNESS →0 ~ 31
↕ ↕
IMAGE →COLOR GAIN →BLUE 1 ~100 ↔RED 1 ~100
↕ ↕
3DNR GAMMA →0.05~1
↕ ↕
SPECIAL NEG.IMAGE →ON/OFF
↕
RESET
↕
EXIT
LENS
↕
EXPOSURE
↕
WHITE BAL
↕
DAY NIGHT
↕
IMAGE
↕
3DNR →ON →LEVEL →1~100
↕
SPECIAL
↕
RESET
↕
EXIT

17
8. OSD MANUAL
SPECIAL MENU STRUCTURE
LENS
↕
EXPOSURE
↕
WHITE BAL CAM TITLE →ON / OFF ↔POSITION CONTROL
↕
↕
DAY NIGHT LANGUAGE →ENGLISH ↔FRANÇAIS ↔РУССКИЙ ↔ESPAÑOL ↔DEUTSCH
↕
IMAGE ON/
OFF
AREA
SEL
AREA
DISPLAY
LEFT/
RIGHT WIDTH TOP/ BOTTOM
↕MOTION → ↔ ↔ ↔ ↔ ↔
3DNR ↕
↕
AREA1~4 ON/OFF MOTION
VIEW ↔SENSITIVITY ↔HEIGHT
SPECIAL →PRIVACY →AREASEL ↔AREADISPLAY ↔LEFT/RIGHT ↔WIDTH ↔TOP/BOTTOM
↕ ↓ ↓ ↕
RESET AREA1~8 ON/OFF COLOR ↔HEIGHT
↕
EXIT SYNC →INT
RESET MENU STRUCTURE
LENS
↕
EXPOSURE
↕
WHITE BAL
↕
DAY NIGHT
↕
IMAGE
↕
3DNR
↕
SPECIAL
↕
RESET →FACTORY RESET
↕
EXIT

18
8. OSD MANUAL
OSD FUNCTION DESCRIPTION
1.LENS
- LEVEL DC
BRIGHTNESS : Enable user to select the
DC level for Brightness of image(1~100).
2. EXPOSURE
: Enable user to set up the function of SHUTTER, AGC.
- SHUTTER
• FLK : Enable user to set up the FLICKERLESS.
(NTSC: 1/100, PAL: 1/120)
• FIXED : Enable user to set up the Shutter Speed.
> 1/60(50), 1/250, 1/500, 1/2K, 1/5K, 1/10K, 1/100K.
* ( ) is for PAL TYPE.
- BRIGHTNESS : Enable user to set up the MANUAL
electronic Shutter value.
- AGC : Enable user to make imager bright to
amplify the Gain.
- SENSE-UP : Low-speed shutter control.
- BLC : The Function of Back Light Compensation.
• HSBLC : Highlight Suppression BLC will darken
image portions for clearer images.
- D-WDR : allows every detail to be captured accurately
even if one portion is bright while other portions are dark.
LENS
BRIGHT 50
RETURN RET┛
EXPOSURE
SHUTTER 1/60
BRIGHTNESS 50
AGC OFF
SENSE-UP AUTO
BLC BLC┛
D-WDR OFF
RETURN RET┛

19
8. OSD MANUAL
3. WHITE BALANCE
: Enable user to represent the accurate white color by controlling the R.G.B level.
• ATW : Enable user to trace the White Balance
automatically in the Wide range.
(2,500K ~ 9,500K)
• PUSH : Enable user to trace the White Balance
automatically in all the range.
• P-LOCK : Enable user to set up automatically
readjusted only at the request of the user.
• MANUAL : Enable user to set the RED
GAIN or BLUE GAIN.
• INDOOR : Enable user to set up 3,200K base mode.
• OUTDOOR : Enable user to set up 5,400K base mode.
4. DAY&NIGHT
: Conversion of output image COLOR/BW depending on exterior environment.
- AUTO : Sensor mode auto change.
- B/W : Enable user to x the output image in B/W.
• BURST ON/OFF : Select the burst signal ON/OFF
when Night condition.
- COLOR : Enable user to x the output image in COLOR.
WHITE BAL MANUAL
BLUE 24
RED 32
RETURN RET┛

20
8. OSD MANUAL
5. IMAGE
:Setting up the FREEZE, MIRROR, D-ZOOM, SHARPNESS, COLOR GAIN,
GAMMA, NEGATIVE IMAGE.
- FREEZE : Setting of moving images in
freeze-frame mode.
- MIRROR
• MIRROR : Enable user to set up
reversed LEFT and RIGHT image.
• V-FLIP : Enable user to set up vertically
ipped video.
• ROTATION : Enable user to set up 180-degree
rotation lp function.
- D-ZOOM : Enable user to expand one part
of the monitor screen for viewing.
- SHARPNESS : Enable user to set up
sharpness control.
- COLOR GAIN : Enable user to set the
RED GAIN or BLUE GAIN.
- GAMMA : Enable user to set up compensation
according to gamma value.
- NEG.IMAGE : Enable user to set up negative
image ON/OFF.
6. 3DNR
: three-dimensional noise reduction.
- LEVEL : Enable user to set up noise
reduction level.
IMAGE
FREEZE OFF
MIRROR OFF
D-ZOOM ON┛
SHARPNESS 5
COLOR GAIN ┛
GAMMA 0.45
NEG.IMAGE OFF
RETURN RET┛
3DNR
LEVEL 50
RETURN RET┛

21
8. OSD MANUAL
7. SPECIAL
: Setting up the CAM TITLE, LANGUAGE, MOTION, PRIVACY, SYNC.
- CAMERA TITLE : Display the title editing menu.
- LANGUAGE : Enable user to set up Language for OSD.
(Option1: English, Russian, Spanish, German, French
Option2: English, Chinese)
- MOTION : The camera monitors the movement of image,
and it sends an alarm signal or OSD icon.
• AREA SELECT : Enable user to select the 4 motion area.
• AREA DISPLAY : Enable user to set up ON/OFF in selected area
• LEFT/RIGHT : Enable user to set up LEFT/RIGHT position in selected area.
• WIDTH : Enable user to set up width in selected area.
• TOP/BOTTOM : Enable user to set up TOP/BOTTOM position in selected area.
• HEIGHT : Enable user to set up height in selected area.
• SENSITIVITY : Enable user to set up the movement detection threshold value.
• MOTION VIEW : Display the motion area on the screen.
- PRIVACY : Privacy is the function that covers the some part on screen to prevent
private life Maximum 8 point covered.
• AREA SELECT : Enable user to set up a area from 1 to 8.
• AREA DISPLAY : Enable user to set up ON/OFF in selected area.
• LEFT/RIGHT : Enable user to set up LEFT/RIGHT position in selected area.
• WIDTH : Enable user to set up width in selected area.
• TOP/BOTTOM : Enable user to set up TOP/BOTTOM position in selected area.
• HEIGHT : Enable user to set up height in selected area.
• COLOR : Enable user to set up MASK COLOR.
- SYNC : Synchronization pulses for lock the viewing monitor on the picture.
• INT : Internal Synchronization system.
SPECIAL
CAM TITLE OFF
LANGUAGE ENGLISH
MOTION ON┛
PRIVACY ON┛
SYNC INT
RETURN RET┛