Label NEXT 75 User manual

USER MANUAL
TRANSLATION OF THE ORIGINAL INSTRUCTIONS
Automation for indoor
automatic swing doors
EN
NEXT 75
NEXT 150
NEXT 120s
NEXT 75/150/120S_EN_Rel.2.0_10/2020 - CD0750EN-MU

RECOMMENDATIONS
THIS INSTRUCTION MANUAL IS INTENDED FOR THE FINAL USER OF A LABEL AUTOMATIC SWING
DOOR SYSTEM; IT IS UNDERSTOOD THAT INSTALLATION AND TESTING MUST HAVE BEEN CARRIED
OUT BY SPECIALISED PERSONNEL.
GENERAL SAFETY WARNINGS
CAREFULLY READ THIS MANUAL BEFORE COMMISSIONING THE AUTOMATIC DOOR.
PROVISIONS
The automation has been designed to be used exclusively with pedestrian automatic swing doors.
The manufacturer shall not be liable for incorrect product usage, as well as for any damages arising from changes to the system made
without its prior consent.
When operating the system, accident prevention regulations must be observed.
The equipment can be used by children of at least 8 years of age and by people with reduced physical, sensory or mental skills, or
by inexperienced people, provided they are supervised, or after the same have received instructions relating to the safe use of the
equipment and to the understanding of the relevant hazards. Children should not play with the equipment. Cleaning and maintenance
intended to be performed by the user must not be carried out by children without supervision. Do not let children stay or play within the
operating range of the door.
REMARKS
Always respect the usage and maintenance conditions provided for by LABEL.
Maintenance and repair operations must only be performed by qualied and properly trained personnel.
PROPER BEHAVIOUR
Only use the automatic door if it is in perfect technical conditions.
In case of failure or malfunction that might a󰀨ect safety, immediately contact the service centre.
Inappropriate use of the system may cause serious injuries and damage.
Automatic Door Solutions

CONTENTS:
1) INDICATIVE DESCRIPTION OF THE SYSTEM 4
2) TECHNICAL DATA 4
3) AUTOMATIC DOOR OPERATION 5
3.1) NORMAL DOOR OPERATION 5
3.2) DOOR OPERATION IN NIGHT LOCK MODE 5
3.3) COURTESY MODE FOR DISABLED 5
4) PROGRAM SELECTORS 6
4.1) MANUAL PROGRAM SELECTOR 6
4.2) MECHANICAL KEY SELECTOR EV-MSEL 6
4.3) DIGITAL PROGRAM SELECTOR ET-DSEL 7
4.4) DIGITAL PROGRAM SELECTOR T-NFC 8
4.5) SELECTOR ET-DSEL GENERAL PROGRAMMING MENU 9
4.6) ET-DSEL SELECTOR USER PASSWORD MANAGEMENT 10
4.7) T-NFC SELECTOR USER PASSWORD MANAGEMENT 12
4.8) LANGUAGE 13
5) OPERATION IN CASE OF POWER SUPPLY FAILURE 13
6) NOTIFICATION OF ERRORS AND OPERATIONAL ISSUES 14
7) MAINTENANCE 15
8) DISPOSAL 15
Automatic Door Solutions

4
1) INDICATIVE DESCRIPTION OF THE SYSTEM
EXTERNAL RADAR
INTERNAL RADAR
OPENING COMMAND
PROGRAM SELECTOR
CLOSING SAFETY SENSOR
OPENING SAFETY SENSOR
AUTOMATION NEXT
ELECTRIC LOCK
FLOOR STOP
2) TECHNICAL DATA
AUTOMATION MODEL NEXT 75 NEXT 150 NEXT 120S
POWER SUPPLY 115/230~, 50/60Hz
POWER 40W 50W 50W
DIMENSIONS OF THE AUTOMATION (L x H x D) 420 x 60 x 74mm 420 x 60 x 74mm 520 x 60 x 74mm
FREQUENCY OF USE continuous
OPERATING TEMPERATURE -15° C +50°C
ELECTRIC MOTOR brushless 24Vdc
POWER SUPPLY OF EXTERNAL ACCESSORIES 24 Vdc, 1A
STAND-BY CONSUMPTION 5 W
EQUIPMENT CLASS class II
SOUND PRESSURE EMISSION 









NOTE:
The grey part indicates the
monitoring zone of radars
and sensors.

5
3) AUTOMATIC DOOR OPERATION
WARNING!!
Always contact the service technician before putting into service the door, to learn how the automation works.
Switch on the power supply by means of the system switch.
The automation electronic control unit beeps shortly to indicate that the automatic door is powered.
The rst opening command starts a calibration cycle during which the door opening speed is very low until the end of the motion, to nd
the stop point; after the delay time has elapsed, the door closes back at normal speed.
3.1) NORMAL DOOR OPERATION
• When something enters the motion sensors (internal and/or external radar) detection area, the door opens and stays open until the
sensors detect the presence, then once the pause delay has elapsed the door closes back.
• When the manual door opening button is pressed, the door opens and stays open until the command remains active, then once the
pause delay has elapsed it closes back.
• If the electronic control unit has been set with the PUSH & GO function you can open the door also with a short manual push.
• If the closing safety sensor detects a presence, the door immediately reopens, and stays open as long as the sensor remains engaged.
• If the opening safety sensor detects a presence, the door stops and remains stationary for the entire period in which the sensor is
engaged; it will complete the opening cycle only after the sensor is released.
• If during the opening motion the door collides against an obstacle, it stops and closes back.
• If, during the closing motion, the door collides against an obstacle, it stops and opens back.
3.2) DOOR OPERATION IN NIGHT LOCK MODE
• The door cannot be opened by means of the external and internal radars.
• The door can only be opened by pressing the OPEN button, or using the Spyco radio-control, if any.
• The safety functions (sensors and behaviour in case of obstruction) are active and operate as described in par. 3.1. related to normal
operation.
3.3) COURTESY MODE FOR DISABLED
This only applies if the electronic control unit has been programmed and set to the disabled people operating mode.
• The disabled person may open the door through a special button or motion sensor.
The door stays open for a delay time long enough to allow the disabled person to cross the door.
• All the safety functions are on.

6
4) PROGRAM SELECTORS
The program selector allows the user to select the operating mode of the door.
Depending on the preference, it is possible to use the manual selector incorporated in the side cap of the automation NEXT, the
mechanical key selector EV-MSEL, or the digital selector ET-DSEL or T-NFC.
Each program selector is fully described below.
4.1) MANUAL PROGRAM SELECTOR
The 3-position manual program selector is the basic solution provided on the automation.
Position I= Automatic bidirectional program
The door automatically opens after an opening command.
Position 0= Manual free door
Automatic operation is disabled and the door can be opened manually.
Position II = a) Night lock program
The door can only be opened through the OPEN input or using the remote
control.
b) Open door program
The door remains motionless in the position of complete opening.
4.2) MECHANICAL KEY SELECTOR EV-MSEL
OPERATING MODE
Insert and turn the key of the selector EV-MSEL to select the desired program.
Open door program
The door remains motionless in the position of complete opening.
Manual free door
Automatic operation is disabled and the door can be opened manually.
Automatic bidirectional program
The door automatically opens after an opening command.
Automatic unidirectional exit only program
To disable entry detection on external Radar input.
Night lock program
The door can only be opened through the OPEN input or using the SPYCO remote control, if any.
The key can be taken out of the selector when in any position in order to prevent undesired changes to the work program.
It can operate in two
di󰀨erent ways depending
on the setting on the
electronic control unit of
the automation:

7
4.3) DIGITAL PROGRAM SELECTOR ET-DSEL
Pressing briey the button , select the automatic door operating mode.
Whenever the button is pressed, you switch from a work program to the next.
The work programs which can be selected using the button are described below
Automatic unidirectional exit only program
To disable entry detection on external Radar input.
Open door program
The door remains motionless in the position of complete opening.
Manual free door
Automatic operation is disabled and the door can be opened manually.
Automatic bidirectional program
The door automatically opens after an opening command.
Automatic unidirectional entry only program
To disable exit detection on internal Radar input.
Night lock program
The door can only be opened through the OPEN input or using the remote control, if any.
Operation of other buttons located on the panel of the program selector ET-DSEL
Partial opening, used only in a double leaf door automation
To activate partial opening, press briey the button ;
the symbol on the display indicates that the function is on.
In a dual leaf door, only the rst leaf (Master) opens if the opening command is given from the internal or
external radar inputs.
Partial opening only operates in bi-directional, unidirectional, and open door automatic programs.
To disable partial opening, press again briey the button .
F2
It can have two distinct functions, depending on the setting of the automation.
a) Disables spring actuated door reclosing after a manual opening.
With F2 o󰀨, the door closes, with F2 on, the door remains stationary after a manual opening.
b) Disables step by step operation
(If enabled in the settings on the electronic control unit of the automation)
Press briey the button F2 to disable step by step operation and enable the automatic closure of the door.
The symbol F2 lights up on the display.
To enable step by step operation, press again the button F2, the symbol F2 turns o󰀨 on the display.
F1
Door opening command
Pressing the F1 button will open the door.
The button F1 may open the door even when the "NIGHT LOCK" work program is selected, if the
automation electronic control unit is set accordingly.

8
4.4) DIGITAL PROGRAM SELECTOR T-NFC
DAILY USE
The selector T-NFC enables to select for daily use 6 di󰀨erent types of programs:
AUTO:
The door opens and closes automatically
in both ow directions with all sensors
active.
ENTRY:
The door opens and closes automatically
only in entry direction:
The sensor connected on the Internal
Radar input is disabled.
EXIT:
The door opens and closes automatically
only in exit direction:
The sensor connected on the External
Radar input is disabled.
OPEN:
The door opens and remains open until
you change the work program.
LOCK:
CLOSED DOOR
The door can be opened automatically
only by means of some specic inputs
(Open, RX).
Each time the door closes, the electric
lock (if any) activates.
MANUAL:
The door can be moved manually
and does not react to any input that is
activated.
Use this work program if you want, for
instance, to clean the panes, being
sure that the door cannot move if you
accidentally activate the opening sensors
or any other activation command.
To change a work program, press the SET button once to exit the "Screen Saver" function and thus activate the
selector (the screen will increase its brightness), now press SET again several times until you position on the
desired work program.
If you have activated the program lock with the SLIDE function, to exit the "Screen Saver" slide your nger from
left to right on the buttons A* - SET - B to activate the selector.
Warning!
If no button is pressed for approximately 20 seconds, the selector automatically switches to
"Screen Saver" mode and reduces the brightness of the display.
In addition to the work program, it is possible to select at any time a partial opening with respect to the standard one (used in double leaf
doors to open only the main leaf).
To do this, press the button A, the corresponding symbol appears on the display and the ow direction icons (if active) will become
thinner.
Press again button A to return to complete opening.
The gure below shows an example with the AUTO program.
DOOR OPENING FROM T-NFC
The button B, if pressed, generates a door opening command,
closure will take place automatically as for the other sensors.
This button is able to open the door even in "LOCK" work program,
if the function is active.

9
4.5) SELECTOR ET-DSEL GENERAL PROGRAMMING MENU
The user can enter the general programming menu when he wishes to select the desired language for the texts that appear on the
display, or when he wishes to enable a password to prevent any unauthorised access to the digital selector ET-DSEL.
DIAGRAM 1
SECTION RESERVED FOR
TECHNICAL STAFF
SECTION RESERVED FOR
TECHNICAL STAFF
SECTION RESERVED FOR
TECHNICAL STAFF
“PASSWORD MANAGEMENT"
SECTION
SECTION RESERVED FOR
TECHNICAL STAFF
"SELECTOR OPTION" SECTION
NOT USED
“LANGUAGE" SECTION
The paragraphs below explain the procedure to be followed to manage the user password and to select the language.

10
4.6) ET-DSEL SELECTOR USER PASSWORD MANAGEMENT
To prevent the door work program from being modied, it is possible to set a password that must be entered every time the selector
ET-DSEL is used.
To enable the password, perform the operations listed below:
1. Press the SET button for 5 seconds to access the general programming menu (see Diagram 1 at para. 4.3.1)
2. Press the button F1 ve times to go to the Password Management sub-menu.
3. Press the Enter button to access the section “Password management”.
PASSWORD MANAGEMENT
PRIMARY PASSWORD (for the system owner-user)
It is a 5-character password used by the user to prevent unauthorized persons from having access to the selector ET-DSEL and change
the work program.
Using a primary password is optional and must be enabled by the system owner.
The default technical password is “A-A-A-A-A”.
WARNING!
When enabling the password, be very careful not to forget the access combination.
SERVICE PASSWORD (for user)
It is a 5-character password that the system's owner may provide to persons authorized to use the selector ET-DSEL.
With the service password, it is only possible to change the work program of the automatic door.
The default service password is “A-A-A-A-A”.
To change the service password, it is necessary to log in using the primary password.
Use the button to move the selection arrow downward, the F2 button to move back upward.
HOW TO CHANGE THE PRIMARY PASSWORD
• Select “PRIMARY PASSWORD”
• Press OK (F1).
• Enter the default primary password “A-A-A-A-A” pressing 5 times the button A.
(If the primary password is not the default password, since it had already been changed before,
enter the currently-used primary password).
• Enter the new primary password, selecting a combination of 5 characters from the letters A-B-
C-D.
This section displays the two passwords available to the nal user, the primary password and the
service password.
The technical password is only reserved for the technical sta󰀨 in charge of installation and
maintenance operations.
• You are prompted to repeat the new password, so enter again the previous combination.
• If the password entered is correct, the message “PASSWORD OK” is displayed for one second,
then the system returns to the PASSWORD MANAGEMENT section. Press the EXIT button
to return to the general programming menu
• If the password you entered does not match the previous one, the display shows PASSWORD
ERROR, the system returns to the section PASSWORD MANAGEMENT and it is necessary to
perform again the procedure.

11
• Enter the primary password
• Enter the new service password, selecting a combination of 5 characters from the letters A-B-C-D.
• You are prompted to repeat the new password, so enter again the previous combination.
• Enter the primary password
• If the password entered is correct, “PASSWORD OK” is displayed for one second and the system
returns to the PASSWORD MANAGEMENT section.
• Press the OFF button (F1) to disable user password usage.
To return to the general programming menu, press the EXIT button twice
Access to the digital selector ET-DSEL as program selector now is free.
HOW TO CHANGE THE SERVICE PASSWORD
• Select “SERVICE PASSWORD”
• Press OK (F1).
Press the EXIT sbutton to return to the general programming menu.
If the password you entered does not match the previous one, the display shows PASSWORD ERROR, the system returns to the section
PASSWORD MANAGEMENT, and it is necessary to perform again the procedure.
ENABLING USER PASSWORD USAGE (primary and service password)
• Select “PASSWORD ON / OFF”
• Press OK (F1).
• Press the ON button to enable the usage of user passwords
and return to the menu PASSWORD MANAGEMENT.
To return to the work program view, press the EXIT
button twice.
From this moment on, whenever the user wants to access the digital selector ET-DSEL to change the automatic door work program, the
primary or service password must be entered.
When the user decides to enable password usage, it is recommended to change the combination of both primary
and service password.
DISABLING USER PASSWORD USAGE
• From the PASSWORD MANAGEMENT section, select “PASSWORD ON / OFF”
• Press the button OK (F1)

12
4.7) T-NFC SELECTOR USER PASSWORD MANAGEMENT
The selector T-NFC enables to prevent the work program change by means of a password.
This function is useful if you want to prevent unauthorized persons from setting the work program of the door.
To do this, you need to enable the user password with the following steps:
Press and hold button D for approximately 2 seconds.
The display will show the message "CODE>....."
Enter the current password (default AAAAA) with the buttons A-B-C-D (5 digits)
Now we are inside the user password area, from where you can access 3 di󰀨erent selections:
PASSWORD 1: To change the code of the main password
PASSWORD 2: To change the code of the service password
PASSWORD ON/OFF: To enable or disable the primary and the service password.
Repeatedly pressing the button B, you can move in sequence to all 3 selections.
Warning!
The main password (1) is the only one that enables to enter the user password area and should therefore be known only by
the owner of the store/organization in which the door is installed. The service password (2) instead is used for employees
or third parties that can use it to change the work programs of the door, but cannot in any way change or disable both
passwords.
To change the password 1, press the button A after selecting PASSWORD 1. The display will show:
Enter the new password.
The next screen will be:
Enter again the new password.
Repeat the same sequence to change password 2.
Finally, in order to enable the password, select PASSWORD ON/OFF by means of button A, and select ON by means of button D (On).
Once you have enabled the password, press the button SET to exit this area and return to the main screen.
To disable the user password, select PASSWORD ON/OFF by means of button A, and select OFF by means of button B (OFF).
Now, after the selector is in "Screen Saver" mode, press the button SET, every time you will be prompted by the selector to enter the
password to access program change.

13
4.8) LANGUAGE
To select the language on the selector ET-DSEL, perform the operations listed below:
1. Press the button for 5 seconds to enter the general programming menu.
(see Diagram 1 in the previous paragraph)
2. Press the button F1 three times to go to the Language sub-menu.
3. Press the Enter button to access the section “Language”.
• Use the buttons F2 and to move the arrow in correspondence with the desired language.
• Press the EXIT button to return to general programming menu.
• Press the EXIT button again to return to the main view of the automatic door work
program.
5) OPERATION IN CASE OF POWER SUPPLY FAILURE
In case of power supply failure the door can be opened and closed manually.
If the door is equipped with an electric lock, use the special key to unlock it.
If the automation is not equipped with battery, depending on the programming of the automation electronic control unit, the door may
operate as follows:
a) The door can be opened by activating any opening command (motion radars, buttons, etc.).
b) The door opens automatically and stays open if the program selector is not set to Night Lock.
POWER LIGHT DISPLAY
ON SELECTOR ET-DSEL ON SELECTOR T-NFC
Mains power supply on and battery under charge.
Mains power supply o󰀨 and door operating with charged
battery.
• Mains power supply o󰀨 and door operating with
battery low.
• Mains power supply on with ine󰀩cient battery.

14
6) NOTIFICATION OF ERRORS AND OPERATIONAL ISSUES
PROBLEM LIKELY CAUSE SOLUTION
The door opens but it doesn't close back.
The motion radars or the closing safety
sensor detect the presence of an object or
of a person.
Check that the radars or the sensors are
not engaged.
The door doesn't complete the opening
cycle and stops along the way.
The opening safety sensor detects an
obstacle. Identify the obstacle and remove it.
The door doesn't respond to the opening
commands.
The MANUAL FREE DOOR function can
be activated. Check the setting of the program selector.
The door stops during its motion and inverts
the running direction.
The door detects an obstacle along its
motion. Identify the obstacle and remove it.
The door experiences friction along its
motion.
Adjust the door;
for this operation please contact the service
centre.
The electronic control unit beeps multiple
times and door operation is irregular.
The defect depends on the number and
length of the beeps.
Contact the service centre to solve the
issue.
On the display appears the symbol
The system has detected a machine
operation error.
Contact the service centre to solve the
issue.
Should any malfunction occur, the Customer must contact the Support Centre and use the door manually, without powering it.

15
7) MAINTENANCE
The maintenance plan must be observed to ensure the service life and the safe operation of the automatic door. It is recommended to
sign a maintenance contract providing for periodic intervention on the system by specialised technicians.
If the user has the program digital selector ET-DSEL or T-NFC, he will be warned about the expiry of the maintenance interval when the
message "SCHEDULED MAINTENANCE" is displayed.
Each maintenance operation is recorded into the maintenance log.
The nal user must limit himself to cleaning the glass surfaces, the xture proles and if necessary the motion and presence sensors,
taking care to lock the door while performing these operations.
8) DISPOSAL
At the end of its lifecycle, this system must be disposed of in accordance with national provisions.
To this purpose, it is recommended to contact specialised operators.

NEXT
Made in Italy
by
S.p.A
Via Ilariuzzi, 17/A - S. Pancrazio P.se - 43126 PARMA - ITALIA
Tel. [phone] - Fax [phone]
[email protected] - www.labelspa.com
LABEL service centre