laerdal Resusci Anne User manual

Resusci Anne Simulator
User Guide
www.laerdal.com
English

22
Resusci Anne Simulator
The Resusci Anne Simulator is a realistic manikin designed to meet the learning objectives of basic
healthcare and intermediate life support. The simulator supports training for CPR, defibrillation,
vital sign recognition and supraglottic airway management procedures.
––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––––
Note
Photos/illustrations may vary from product.

2 3
Contents
2
1 Items included 4
2Get started 6
3Use 10
4Maintenance 15
5Cleaning 20
See Important Product Information pamphlet for more information or visit www. laerdal.com
English

4
Items Included
1
Airway Management Head
Torso
Blood Pressure Arm IV Arm
Pelvis
Blood Pressure (BP) Cuff Manual
Defibrillation
Plates
SimPad (Link Box with lithium-ion
battery installed in manikin).
SimPad Wrist Strap and Sleeve
Extrication
Rescue Legs
Pants
Full body
soft pack
2 x AC Adapters
3 Eye Sets (normal,
constricted, dilated pupils)
Air Pump

4 5
Items Included
Airway Management Head
Torso
Blood Pressure Arm IV Arm
Pelvis
Blood Pressure (BP) Cuff Manual
Defibrillation
Plates
SimPad (Link Box with lithium-ion
battery installed in manikin).
SimPad Wrist Strap and Sleeve
Extrication
Rescue Legs
Pants
Full body
soft pack
2 x AC Adapters
3 Eye Sets (normal,
constricted, dilated pupils)
English
Simulated BloodUSB Cable Lubricant

6
Get Started
2
Charge battery
Attach legs
Charge battery using
AC adapter included.
Detach lower chest skin
and fold back.
Remove stomach foam.
Twist to disconnect
tubing between
pelvis and torso.
Disengage pelvis
from torso.
Do not disrupt
connection wires
between pelvis
and torso.
Remove bolt
connector.

6 7
Get Started
To remove legs, reverse procedure.
Remove wing nut
and washer from bolt
inserted in leg. Spring
assembly remains in leg.
RemoveThigh Pad
and insert bolt
through hole in pelvis.
Slide washer and wing
nut back over bolt.
Use screwdriver to
secure screw while
driving bolt into wing nut.
Reattach pelvis,
with legs, to torso.
Replace bolt
connector to
secure.
Reconnect tubing
between pelvis and
torso and place in
grove.
Slide loose wires/tubes
down into pelvis.
English

8
Get Started
Connect blood pressure cuff to arm
Connect external microphone (not included)
Fill air container
Note
If spontaneous breathing is activated and no chest rise is observed, ensure there is enough air in
the air container. Refill as necessary.
Place blood
pressure cuff
on arm.
Connect clear tubing on
cuff to blood pressure
connector on BP tubing.
Insert connector and
twist to click into place.
Plug microphone into jack
on side of Link Box. Pink
extension cable provided.
Attach air pump hose to
fill valve located on right
side of torso.
Air container is located
inside pelvis.
Detach air pump from
fill valve.
Use manual pump
provided. Do not to
exceed 10 bar (145 psi).

8 9
Get Started
Prepare IV Arm
Connect SimPad to simulator
Refer to SimPad User Guide for instructions.
Connect PC to simulator (optional for SimPad Patient Monitor)
Select a vein and
attach IV tubing
to IV bag.
Allow fluid to flow
through arm and out
of other vein. Clamp
off flow (with a knot
or clamp) of fluid
from open vein.
To use PC software,
connect Ethernet cable
between simulator and
a computer. (Cable not
included).
English

10
Use
3
On/Off
Head tilt/Chin lift
Jaw thrust
Breathing
Spontaneous breathing is controlled by the SimPad.
On/Off button