laguna P Flux 1 User manual

1.5HP CYCLONE
1 MICRON CANISTER | HEPA CANISTER

1.5HP Mobile Dust Cyclone Manual
1
TABLE OF CONTENTS
Important Safety Instructions
Safety Guidelines - Definitions
General Safety Rules
Additional Safety For Dust Collectors
Power Connections
Motor Specifications
Grounding Instructions
Functional Description
Product Specifications
Unpacking
Assembly
General Tool Assembly
Maintenance Procedures
Cleaning the Filter
Changing the Filter Bag
Emptying the Drum
Routine Inspection
Trouble Shooting
Parts breakdown and Parts list

1.5HP Mobile Dust Cyclone Manual
2
IMPORTANT SAFETY INSTRUCTIONS
READ AND UNDERSTAND ALL WARNINGS AND OPERATING
INSTRUCTIONS BEFORE USING THIS EQUIPMENT. Failure to follow all instructions listed
below, may result in electric shock, fire, and/or serious personal injury or property
damage.
Woodworking can be dangerous if safe and proper operating procedures are not followed.
As with all machinery, there are certain hazards involved with the operation of the product.
Using the machine with respect and caution will considerably lessen the possibility of
personal injury. However, if normal safety precautions are overlooked or ignored, personal
injury to the operator may result. Safety equipment such as guards, push sticks, hold-
downs, featherboards, goggles, dust masks and hearing protection can reduce your
potential for injury. But even the best guard won’t make up for poor judgment,
carelessness or inattention. Always use common sense and exercise caution in the
workshop. If a procedure feels dangerous, don’t try it. Figure out an alternative procedure
that feels safer. REMEMBER: Your personal safety is your responsibility.
This machine was designed for certain applications only. We
strongly recommend that this machine not be modified and/or used for any application
other than that for which it was designed. If you have any questions relative to a
particular application, DO NOT use the machine until you have first contacted the
manufacturer to determine if it can or should be performed on the product.
If you have any questions relative to its application DO NOT use the product until you
have contacted the manufacturer and we have advised you.
When using an electrical appliance, basic precautions should always be followed, including
the following:
READ ALL INSTRUCTIONS BEFORE USING (THIS APPLIANCE)
To reduce the risk of fire, electric shock, or injury:
1. Do not leave appliance when plugged in. Unplug from outlet when not in use and before
servicing.
2. Do not use outdoors or on wet surfaces
3. Do not allow to be used as a toy. Close attention is necessary when used by or near
children.
4. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
5. Do not use with damaged cord or plug. If appliance is not working as it should, has
been dropped, damaged, left outdoors, or dropped into water, return it to a service center.

1.5HP Mobile Dust Cyclone Manual
3
6. Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull cord
around sharp edges or corners. Do not run appliance over cord. Keep cord away from
heated surfaces.
7. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
8. Do not handle plug or appliance with wet hands.
9. Do not put any object into openings. Do not use with any opening blocked; keep free of
dust, lint, hair, and anything that may reduce air flow.
10. Keep hair, loose clothing, fingers, and all parts of body away from openings and
moving parts.
11. Turn off all controls before unplugging.
12. Use extra care when cleaning on stairs.
13. Do not use to pick up flammable or combustible liquids, such as gasoline, or use in
areas where they may be present.
14. Connect to a properly grounded outlet only. See Grounding Instructions.
SAVE THESE INSTRUCTIONS
1. Read and understand the warnings posted on the machine and in this manual.
Failure to comply with all of these warnings may cause serious injury.
2. Replace the warning labels if they become obscured or removed.
3. This 1.5HP Portable Cyclone Dust Collector is designed and intended for use by
properly trained and experienced personnel only. If you are not familiar with the
proper and safe operation of this type of dust collector, do not use until proper
training and knowledge have been obtained.
4. Do not use this machine for other than its intended use. If used for other purposes,
LAGUNA TOOLS INC., disclaims any real or implied warranty and holds itself
harmless from any injury that may result from that use.
5. Always wear approved safety glasses/face shields while using this machine.
6. Before operating this dust collector, remove tie, rings, watches and other jewelry,
and roll sleeves up past the elbows. Remove all loose clothing and confine long hair.
Non-slip footwear or anti-skid floor strips are recommended. Do not wear gloves.
7. Wear ear protectors (plugs or muffs) during extended periods of operation.
8. Some dust created by power sanding, sawing, grinding, drilling and other
construction activities contain chemicals known to cause cancer, birth defects or
other reproductive harm. Some examples of these chemicals are:
•Lead from lead based paint.
•Crystalline silica from bricks, cement and other masonry products.
•Arsenic and chromium from chemically treated lumber.

1.5HP Mobile Dust Cyclone Manual
4
Your risk of exposure varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals, work in a well-ventilated area and work
with approved safety equipment, such as face or dust masks that are specifically
designed to filter out microscopic particles.
9. Do not operate this machine while tired or under the influence of drugs, alcohol or
any medication.
10.Make certain the switch is in the OFF position before connecting the machine to the
power source.
11.Make certain the machine is properly grounded.
12.Make all machine adjustments or maintenance with the machine unplugged from
the power source.
13.Form a habit of checking to see that all extra equipment such as adjusting keys,
wrenches, scrap, stock, and cleaning rags are removed away from the machine
before turning on.
14.Keep safety guards in place at all times when the machine is in use. If removed for
maintenance purposes, use extreme caution and replace the guards immediately
when maintenance is complete.
15.Make sure the dust collector is on a flat even surface and the wheels locked in place
before use.
16.Check damaged parts. Before further use of the machine, a guard or other part that
is damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment of moving parts, binding of
moving parts, breakage of parts, mounting and any other conditions that may
affect its operation. A guard or other part that is damaged should be properly
repaired or replaced.
17.Provide for adequate space surrounding work area and non-glare, overhead lighting.
18.Keep the floor around the machine clean and free of scrap material, oil and grease.
19.Keep visitors a safe distance from the work area. Keep children away.
20.Make your workshop child proof with padlocks, master switches or by removing
starter keys.
21.Give your work undivided attention. Looking around, carrying on a conversation and
“horse-play” are careless acts that can result in serious injury.
.

1.5HP Mobile Dust Cyclone Manual
5
22.Maintain a balanced stance at all times so that you do not fall or lean against the
dust collector. Do not overreach or use excessive force to perform any machine
operation.
23.Use the right tool at the correct speed and feed rate. Do not force a tool or
attachment to do a job for which it was not designed. The right tool will do the job
better and safer.
24.Use recommended accessories; improper accessories may be hazardous.
25.Maintain machinery with care. Follow instructions for lubricating and changing
accessories.
26.Turn off the machine before cleaning. Use a brush or compressed air to remove
dust or debris — do not use your hands.
27.Do not stand on the machine. Serious injury could occur if the machine tips over.
28.Never leave the machine running unattended. Turn the power off and do not leave
the machine until it comes to a complete stop.
29.Never operate or run the machine without closing the drum up against the lid.
Failure to do so will result in the machine amperage increasing and may trip your
circuit.
Familiarize yourself with the following safety notices used in this manual:
SAFETY GUIDELINES - DEFINITIONS
This manual contains information that is important for you to know and understand. This
information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS.
To help you recognize this information, we use the symbols below. Please read the manual
and pay attention to these sections.
Indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.

1.5HP Mobile Dust Cyclone Manual
6
Used without the safety alert symbol indicates potentially hazardous
situation which, if not avoided, may result in property damage.
GENERAL SAFETY RULES
WARNING FAILURE TO FOLLOW THESE RULES MAY RESULT
IN SERIOUS PERSONAL INJURY.
FOR YOUR OWN SAFETY, READ AND UNDERSTAND THE INSTRUCTION MANUAL
BEFORE OPERATING THE MACHINE. Learn the unit’s application and limitations as well
as the specific hazards peculiar to it.
KEEP WORK AREA CLEAN. Cluttered areas and benches invite accidents.
DON’T USE IN DANGEROUS ENVIRONMENT. Don’t use this unit in damp or wet
locations, or expose it to rain. Keep work area well-lighted.
KEEP CHILDREN AND VISITORS AWAY. All children and visitors should be kept a safe
distance from work area.
DISCONNECT UNIT before servicing.
CHECK DAMAGED PARTS. Before further use of the unit, properly repair or replace any
part that is damaged.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN
SERIOUS INJURY.
ADDITIONAL SAFETY FOR DUST COLLECTORS
Intended use. This dust collector is only intended for collecting wood dust and chips from
woodworking machines. Do not use this dust collector to collect metal, dirt, pebbles,
drywall, asbestos, lead paint, silica, liquids, aerosols, or any flammable, combustible, or
hazardous materials.
Hazardous dust. Dust created while using machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust hazards associated with each work piece
material, and always wear a NIOSH-approved respirator to reduce your risk.

1.5HP Mobile Dust Cyclone Manual
7
Dust allergies. Dust from certain woods may cause an allergic reaction in people and
animals.
Make sure you know what type of wood dust you will be exposed to in case there is a
possibility of an allergic reaction.
Wear respirator. Fine dust that is too small to be caught in the filter will be blown into
the ambient air during operation. Always wear a NIOSH-approved respirator during
operation and for a short time after to reduce your risk of permanent respiratory damage.
Emptying dust. When emptying dust from the collection container, wear a respirator and
safety glasses. Empty dust away from ignition sources and into an approved container.
Disconnecting power supply. Turn the switch off, disconnect the dust collector from the
power supply, and allow the impeller to come to a complete stop before leaving the
machine unattended or doing any service, cleaning, maintenance, or adjustments.
Suspended dust particles and ignition sources. Do not operate the dust collector in
areas were explosion risks are high. Areas of high risk include, but are not limited to,
areas near pilot lights, open flames, or other ignition sources.
Fire suppression. Only operate the dust collector in locations that contain a fire
suppression system or have a fire extinguisher nearby.
Impeller hazards. Do not place your hands or tools near the open inlet during operation
for any reason. The powerful suction could easily cause accidental contact with the
impeller, which will
cause serious personal injury or damage to the machine. Always keep small animals and
children away from open dust collection inlets.
Avoiding sparks. Do not allow steel or rocks to strike the impeller—this may produce
sparks.
Sparks can smolder in wood dust for a long time before a fire is detected. If you
accidentally cut
Into wood containing tramp metal (nails, staples, spikes, etc.), immediately turn off the
dust collector, disconnect it from power, and wait for the impeller to stop—then empty the
collection container into an approved airtight metal container.
Operating location. To reduce respiratory exposure to fine dust, locate permanently
installed dust collectors away from the working area, or in another room that is equipped
with a smoke detector. Do not operate the dust collector in rainy or wet locations—
exposure to water may create a shock hazard or decrease the life of the machine.
Static electricity. Plastic dust lines generate high amounts of static electricity as dust
chips pass through them. Although rare, sparks caused by static electricity can cause
explosions or fire. To reduce this risk, make sure all dust lines are thoroughly grounded by
using a grounding wire.

1.5HP Mobile Dust Cyclone Manual
8
Regular cleaning. Regularly check/empty the collection bags or drum to avoid the
buildup of fine dust that can increase the risk of fire. Make sure to regularly clean the
surrounding area where the machine is operated—excessive dust buildup on overhead
lights, heaters, electrical panels, or other heat sources will increase the risk of fire.
This means that if precautions are not heeded, it may result in minor injury and/or
possible machine damage.
This means that if precautions are not heeded, it may result in serious injury or possibly
even death.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
POWER CONNECTIONS
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE
MACHINE IN DAMP LOCATIONS.

1.5HP Mobile Dust Cyclone Manual
9
MOTOR SPECIFICATIONS
Your machine is wired for 240volts, 50 HZ alternating current. Before connecting the
machine to the power source, make sure the switch is in the "OFF" position.
GROUNDING INSTRUCTIONS
THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT
THE OPERATOR FROM ELECTRIC SHOCK.
1. This appliance must be connected to a grounded metal, permanent wiring system; or
an equipment-grounding conductor must be run with the circuit conductors and connected
to the equipment-grounding terminal or lead on the appliance.
The installer, such as a qualified electrician, cut (or bend over) and insulate the grounding
conductor from a field wiring supply cable.
In the event of certain types of malfunctions or breakdowns, grounding provides a path of
least resistance for electric current—in order to reduce the risk of electric shock.
Improper connection of the equipment-grounding wire can result in a risk of electric shock.
The wire with green insulation (with or without yellow stripes) is the equipment-grounding
wire. If repair or replacement of the power cord or plug is necessary, do not connect the
equipment-grounding wire to a live (current carrying) terminal.
Check with a qualified electrician or service personnel if you do not understand these
grounding requirements, or if you are in doubt about whether the tool is properly
grounded. If you ever notice that a cord or plug is damaged or worn, disconnect it from
power, and immediately replace it with a new one.
Full Load a mperage Draw
Amp draw at 240V ( p r e wi r e d ) .................. 9 Am ps
Power Supply Circuit Requirements
The power source c i r cu i t for your m a ch i ne must be grounded and rated for the
amperage
g iv en below. Never replace a circuit breaker on an exist ing circuit with
one of higher
amperage without consulting a qualified electrician to ensure
compl i ance with wiring codes. If you are unsure about the wiring codes in your
area or you plan to connect your machine to a shared circuit, consult a qualified
electrician.
C i r c u i t Size ( 240 V ) .................................. 15 A m p s

1.5HP Mobile Dust Cyclone Manual
10
IN ALL CASES, MAKE CERTAIN THE RECEPTACLE IN QUESTION IS
PROPERLY GROUNDED. IF YOU ARE NOT SURE, HAVE A QUALIFIED ELECTRICIAN CHECK
THE RECEPTACLE.
240 VOLT Single-Phase Operation
The motor supplied with your machine is a single voltage, 240 volt motor. It is shipped
ready-to-run for 240 volt operation.
FUNCTION
High frequency remote control switch
Hand held remote controller
ON/OFF Switch
Receiver SET button
Octagon drum detection
HEPA Filter detection
On board circuit breaker
OFF button
ON button
*Remote set button
*Used to match up a new hand held
controller with the remote switch

1.5HP Mobile Dust Cyclone Manual
11
PROGRAMMING THE REMOTE CONTROL
1. Ensure the machine is switch ON before programming the remote control.
2. Press the Black Receiver set button on the bottom of the remote switch until you hear two
beeps.
3. Press the Remote set button on your hand held controller simultaneously with the RED
button until you hear three beeps to complete the set up.
Receiver set button

1.5HP Mobile Dust Cyclone Manual
12
PRODUCT SPECIFICATIONS
Motor
1100w (1.5hp)
Power Supply
220-240V / 50Hz / 1PH
Running Amp
(with 6" inlet) 9A @ 240v
Recommended Breaker Size (MCB)
20 Amps (Type D)
Airflow (Traditional Method)
1786m3/hour (1051cfm)
Airflow (Realistic Method)
1224m3/hour (720cfm)
Max. Static Pressure
256mm in water (10.1")
Fan Diameter
340mm (13.5")
Inlet Diameter
1x 150mm or 2 x 100mm (1 x 6" or 2 x 4")
Switch
High frequency remote control switch
Noise Level
70 dB(A) @ 3m
Drum Collection Capacity
145 Litre octagonal drum
Packing Size (WxDxH)
1170 x 600 x 1750mm
Machine Weight (Net Weight)
122kg
Shipping Weight (Gross Weight)
150kg
Filter Media
Filtering area: 4.5m2 (48ft2)
Cartridge Filter
400mm diameter x 500mm height
Filtration Size
HEPA 99.2% @ 0.4 micron
Drum Collection Bag Layflat Size
810 x 1090mm (32" x 43")
Filter Collection Bag Layflat Size
N/A

Tel. [phone] Fax. [phone] email; [email protected]
Website: www.charnwood.net VAT GB 290 2170 80
Charnwood Machinery Ltd, Cedar Court, Walker Road, Bardon Hill,
Leicestershire, LE67 1TU, England
Registration No:1316450
Declaration of Conformity for CE Marking
Charnwood Machinery Ltd
Cedar Court
Walker Road
Bardon Hill
Leicestershire
LE67 1TU
England
Declare that Industrial Dust Collector & Air Cleaner
Models B Flux, C Flux1, C Flux3, P Flux1, P Flux3
Conforms with the following Directives:
Machinery Directive 2006/42/EC
And further conforms with the following EU harmonized standard;
EN ISO 12100:2010, EN 60204-1:2006/AC:2010
I hereby declare that equipment named above has been tested and found to comply with
the relevant sections of the above referenced specifications. The machinery complies with
all essential requirements of the directive.
Signed: Dated: 09/11/2017 Location: Leicestershire
Richard Cook
Director

1.5HP Mobile Dust Cyclone Manual
14
UNPACKING
Your 1.5HP Mobile Dust Cyclone comes packed in a single box. Before attempting to
assemble this machine, follow these directions for unpacking:
1. Carefully cut the banding straps and remove them from the box.
2. Cut along the tape line at the top of the box.
3. Remove all parts from the top of the styrofoam and set aside.
4. Remove the styrofoam packing material from the top of the machine.
5. Carefully take out the machine components from the box and set aside.
6. Using the diagram below ensure that all parts are present and in good condition.
DESCRIPTION (QUANTITY) Figure 1
A. Motor
B. Switch and remote controller
C. Dust chute
D. Canister shield (front and back)
E. Top upright supports (3)
F. Canister cover plate
G. Base frame
H. HEPA Canister filter
I. Canister shield (side)
J. Octagon drum left panel
K. Octagon drum right panel
L. Octagon drum front panel
M. Octagon drum back panel
N. Octagon drum base panel
Report any missing or damaged parts to your dealer or distributor. Prior to tool
assembly and use, read this manual thoroughly to familiarize yourself with proper
assembly, maintenance and safety procedures.
G
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
V
V1
V2
V3
Hardware
box
Manual
O. Octagon drum lid
P. Octagon drum foot peddle
Q. Canister end cap with 4” port
R. Lower upright supports (3)
S. Vacuum suction ring
T. Upright support reinforcement plate (3)
U. Foot peddle bar (left and right)
V. Foot peddle assembly fittings
V1. Lower triangular support plate (2)
V2. Foot peddle bar support (2)
V3. Lower support plate (2)
W. Inlet adapter
X. Hardware box
Y. Operating and Parts Manual
X
Y
A
B
C
D
E
F
H
I

1.5HP Mobile Dust Cyclone Manual
15
GENERAL TOOL ASSEMBLY
This step requires two adults. This 1.5 HP Mobile
Dust Cyclone is heavy, be careful when lifting and handling it! Failure to
comply may cause serious injury and/or damage to the machine and/or
property!
Tools Required
10mm wrench / 12mm wrench / 14mm wrench
Phillips screwdriver
4mm hex wrench / 5mm hex wrench
To assemble your dust cyclone, follow these steps:
For your own safety, do not connect the machine to the power source until
the machine is completely assembled. Please also make sure that you read
and understand the entire instruction manual.
ASSEMBLY TIME ESTIMATE 5 hour to 6 hours
Step One: Turn the unit upside down. Make sure you use a cushion under the
canister top side to even out the unit to the same height as the motor. Do
not have the unit lopsided.

1.5HP Mobile Dust Cyclone Manual
16
Step Two: Remove the base which has been fastened to the (3) top upright
supports.
Step Three: Secure the (4) 4” wheels to the underside of the base using (16)
5/16”*3/4” hex bolts and (16) 5/16”*od18*2T flat washers.

1.5HP Mobile Dust Cyclone Manual
17
Step Four: Turn the base around with it standing on the (4) 4” wheels and
secure the three lower upright support panels using (6) 3/8”*3/4” hex bolts
and (6) 3/8”*OD23*2t flat washers.
Each lower upright support panels numbered for its specific location.
A – shown with one dot is located on the canister side.
B – shown with two dots is located on the front side
C – shown with three dots is located on the opposite end.
Step Five: Unbuckle the clamp holding the canister to the dust chute. Remove
the canister filter and set aside.
A
C
B
A
B
C

1.5HP Mobile Dust Cyclone Manual
18
Step Six: Secure the base with (3) lower upright support panels to the unit
using (6) 5/16”*3/4” hex bolts and (6) 5/16”*OD18*2t flat washers.
Step Seven: Secure the (3) upright support reinforcement plates using (12)
5/16”*3/4” hex bolts and (12) 5/16”*OD18*2t flat washers.

1.5HP Mobile Dust Cyclone Manual
19
Step Eight: With the help of another person, lift the unit up carefully to the
right side up with the motor on top and the wheels at the bottom.
Step Nine: Attach the canister filter back in place and secure with clamp. It does
not matter which side you choose to position the clamp.