Lake Shore 4-Way Sand & Water Table User manual

2. Use 16 short bolts, washers and nuts to attach both end braces to the
connector braces. Make sure the short legs of the end braces are
both on the same side of the assembly, as shown below.
Connect the nuts and bolts loosely.
3. When all the hardware is in place, use a Phillips screwdriver and
pliers or a wrench to tighten all of the bolts and nuts securely.
4. Adjust the table legs to one of three heights.
Simply push in the tabs and slide the legs up or
down, as shown. Be sure to keep all the legs at
the same height, and to adjust them before you
place anything in the tubs.
5. Drop the tubs into
place, and fill each
one with sand, water
or other materials.
That’s all there is to it—your new sand & water table is ready for play!
4-Way
Sand & Water Table
This cleverly designed table lets 4 children explore the properties of
sand and water at the same time! The textured tubs lift out easily for
cleaning and changing materials, and adjustable legs allow you to
choose the right height for your students.
To assemble the table, simply follow the instructions in this guide.
We’ve supplied the hardware, so all you need is a Phillips screwdriver
and pliers or an adjustable wrench.
Before You Begin
Separate and identify the following components:
• 1 double-center brace • 16 short bolts and locking nuts
• 2 end braces • 16 washers
• 8 connector braces • 4 plastic tubs
• 8 long bolts and locking nuts
©Lakeshore 2003 TT678
[phone] Ages 3+
www.lakeshorelearning.com
(continued on back)
Note: Attach the locking nuts with the plastic
side facing out, as shown at left.
1. Use 8 long bolts and nuts to attach the connector braces to the
double-center brace, as shown. Note that the hole positions on
one side of each connector
brace are closer to the end
of the brace. Make sure
that this side goes next to
the center brace for all 8
connector braces. (If the
connector braces have been
assembled properly, the tops
of all the braces will be level.)
Connect the nuts and bolts
loosely. (You will tighten them
after all the hardware is in place.)
short leg
holes closer
to ends
short leg

2. Use 16 short bolts, washers and nuts to attach both end braces to the
connector braces. Make sure the short legs of the end braces are
both on the same side of the assembly, as shown below.
Connect the nuts and bolts loosely.
3. When all the hardware is in place, use a Phillips screwdriver and
pliers or a wrench to tighten all of the bolts and nuts securely.
4. Adjust the table legs to one of three heights.
Simply push in the tabs and slide the legs up or
down, as shown. Be sure to keep all the legs at
the same height, and to adjust them before you
place anything in the tubs.
5. Drop the tubs into
place, and fill each
one with sand, water
or other materials.
That’s all there is to it—your new sand & water table is ready for play!
4-Way
Sand & Water Table
This cleverly designed table lets 4 children explore the properties of
sand and water at the same time! The textured tubs lift out easily for
cleaning and changing materials, and adjustable legs allow you to
choose the right height for your students.
To assemble the table, simply follow the instructions in this guide.
We’ve supplied the hardware, so all you need is a Phillips screwdriver
and pliers or an adjustable wrench.
Before You Begin
Separate and identify the following components:
• 1 double-center brace • 16 short bolts and locking nuts
• 2 end braces • 16 washers
• 8 connector braces • 4 plastic tubs
• 8 long bolts and locking nuts
©Lakeshore 2003 TT678
[phone] Ages 3+
www.lakeshorelearning.com
(continued on back)
Note: Attach the locking nuts with the plastic
side facing out, as shown at left.
1. Use 8 long bolts and nuts to attach the connector braces to the
double-center brace, as shown. Note that the hole positions on
one side of each connector
brace are closer to the end
of the brace. Make sure
that this side goes next to
the center brace for all 8
connector braces. (If the
connector braces have been
assembled properly, the tops
of all the braces will be level.)
Connect the nuts and bolts
loosely. (You will tighten them
after all the hardware is in place.)
short leg
holes closer
to ends
short leg