Lami Corporation Rose-63CL User manual

2014.05 Rev.1
Instruction Manual

1
Table of Contents
Preface
Thank you for purchasing our 【 】.
This Instruction Manual (document) includes details for safe use of this product.
Please read this document thoroughly before using the product.
Also, carefully store this document for immediate use whenever necessary.
■Preface P 1
┗Table of Contents .................................................................................................................................. P
1
■Precautions Before Use P 2
┣Meaning of Symbols P 2
┣Precautions for Use P 3
┗Place for Installation ............................................................................................................................. P 4
■Characteristics and Confirmation of Parts P 5
■Installation of the Machine P 6
┣Stand Assembly Method........................................................................................................................ P 6
┣Foot Switch Installation Method............................................................................................................ P 6
P 6
┗Underfilm Shaft Unit Installation Method .........................
■Name of Each Part P 7
┣Main Body of Rose-63CL ....................................................................................................... P 7
Operation Panel..................................................................................................................................... P 7
┗
.............................................................................................................................
.............................................................................................................................
■Before Processing Laminate P 8
┗About Laminate Film ............................................................................................................................. P
8
■Cold Laminate Processing P 9
┗Installation and Processing of Cold Laminate Film .................................................................................P 9
■Maintenance P 11
┣Cleaning of Roller..................................................................................................................................P 11
┣Cleaning of paper tube holder.................................................................................................................P 11
┗Cover the product with cloth after use.....................................................................................................P 11
■Troubleshooting P 12
┣Power does not turn on · machine does not function................................................................................P 12
┣Product malfunctions or power is immediately turned off........................................................................P 12
┣Wrinkles are formed in the processing material....................................................................................... P 12
┗Processing material cannot be inserted · does not come out.....................................................................P 12
■Others P 13
┣Product Specifications............................................................................................................................P 13
┗Contact .................................................................................................................................................. P 13
........
....................................................................
.....

2
Meaning of Symbols
Precautions Before Use
This document uses symbols to explain the degree of harm and damage caused by incorrect use of the product and to
prevent harm on customers and others or damage on properties.
Warning If this symbol is neglected and the product is handled incorrectly, serious injury or death may
occur.
Caution If this symbol is neglected and the product is handled incorrectly, human injury or physical
damage on properties may occur.
This symbol indicates matters to be followed
to avoid injury.
This symbol prohibits disassembly of the
device for safety.
This symbol instructs the user to remove
power plug from the outlet for safety.
This symbol prohibits touching of the
product with wet hands.
This symbol instructs the user to connect
grounding for safety.
This symbol prohibits wetting of the
product by water.
This symbol warns the user about the risk of
hands rolling into the roller.
This symbol shows concern for electric
shock under improper handling.
This symbol shows concern for smoke and
ignition under improper handling.

3
Precautions for Handling
Warning
Power cable included in the product must be used. Do not use power supply not indicated on the product.
Do not place heavy objects on power cable, place cables nearby heating devices, or complex wiring.
Do not process power cable or use damaged power cable.
Accurately insert to the end of electrode.
When inserting power cable, the plug must be held. Excessive bending, twisting or pulling can damage the cable interior
and cause electric shock, fire, and failure.
※Contact our company or store when power cord is damaged.
Regularly remove power cable from the outlet to clean the root and gap of electrode. Do not insert cable with foreign
substances such as dust attached.
Do not install the product in places with high temperature and humidity or poor ventilation, places with combustible and explosive gas
or poisonous gas, places covered with dust, and on top of easily burnt objects. When installing against a wall, the product should be
placed at least 50cm away from the wall.
Do not approach the product to firearms, high temperature, metals, and easily burnt objects. Do not put liquids into the
machine.
Do not disassemble or remodel the machine.
Do not use the product in abnormal state such as smoke, strange odor, and noise. If such condition is found, immediately
turn off the power switch and remove power cable from the outlet before contacting the store or our company. The product
must never be repaired by the customer for safety purpose.
Caution
Power cable must be removed from the outlet when the product is not used for long time.
Do not insert power cable with wet hands.
Grounding must be connected before connecting power to power cable. Power cable must be removed before grounding
disconnection.
Especially, keep the product away from children.
Do not ride the product or put heavy objects on top.
Do not place the product in unstable places (oscillating place, slanted place, and place with vibration of other
machineries). The product may fall down or over to injure persons nearby.
Avoid direct wind from air conditioner.
Never block the air vent. Blocked air vent can cause failure or fire from accumulation of internal heat.
During operation or insertion of laminate, be careful about clothes such as neck tie and necklace and body parts from entering the
device.
When film glue is attached to the laminate roller, squeeze cloth stained with neutral detergent and wipe out. (※Do not
clean with benzene, thinner, or sponge.)
Lift the roller for laminate processing.
When the machine is not used, cover with a cloth to keep away from direct light or fluorescent light. Light can result in
rapid degeneration of the laminate roller rubber.
For safety, transport this product after turning the power switch off and removing power cable from the outlet.

4
more than 1000mm
more than 500mm
more than 500mm
more than 500mm
Place for Installation
This device shall be installed in the following places.
●Horizontal and stable place
Use as slanted or in unstable state may result in adverse effects such as paper return.
Also, unexpected accidents can occur.
●Place where exclusive power outlet is available
Do not use power types other than the rated voltage regulated on this Manual.
Grounding and earth leakage breaker must be installed.
●Place with low humidity and sound ventilation
Installation of this product in place with high humidity can result in short circuit or failure.
Avoid outdoor places and places with direct light or air conditioner wind.
●Workability
Secure sufficient space for workability.
Do not install the product too close to walls. If possible, space between the product and wall should be wide
enough to allow human passage.

5
Instruction manual
（this document）
Hex wrenchFoot switch
Stand（assembly type）
Assembly type film shaft １prevents set
ROSE-63CL main body
Characteristics
●Large diameter roller
●Speed of laminate processing can be adjusted steplessly
●Shaft with scale which easily adjust center of processing material
Confirmation of Parts
The following parts and documents are included in the main body.
If there is a missing part, contact a nearby business office of our company or store from which the product was
purchased.

6
Attach to the left side of the body. Attach to the right side of the body.
Attach the underfilm shaft unit in the front part of the machine.
Each shaft holder has different shape. Attach them to the machine correctly,
and attach the shaft correctly.Scale of the shaft is in the front part.
Underfilm Shaft Installation Method
There is an insertion hole of foot switch at the rear part of the
machine. If cap is attached, remove it and insert foot switch plug
carefully. Be sure to take care of convex part. Convex surface
prevents from insertion in incorrect direction. Check the shape
of the insertion hole before inserting. It may cause failure
to insert the plug in an incorrect direction
When not using foot switch, you can disconnect the cable
by pulling the lock.
Foot Switch Installation Method
Stand is assembly type.
①Be dented area of the stands forward inside,and attach the center pillar.
②Attach casters with brake to the front part of the stand.
③attach casters without brake to the rear part of the stand.
②
②
③
③①
①
Stand Assembly Method
Installation of the Machine

7
※If displayed password requirement, press the set button.
This mode is used for maintenance.
①Cold LED
LED is lit up during cold laminating
②Heater LED
LED is lit up during heater is ON
③Prepare LED
LED is lit up when heater temperature reaches set temperature
④LCD Display Panel（Displayed when heater switch is ON）
Left:set temperature Right:present temperature
⑤Set Button
For setting of heater temperature
⑥Up Button (Temperature)
⑦Down Button (Temperature)
⑧Enable/disable switch for foot switch
Continue:Foot switch operation is disable
Inching:Foot switch operation is enable and roller works during pressing it.
⑨Forward/Reverse Switch
You can change the direction of roller rotation
⑩Heater Switch
When this switch is ON, heater temperature rise to set temperature.
When not using heater, please turn this switch OFF.
⑪Speed Control Dial
Turning this dial to the right direction increase rotation speed.
Operation panel
①Stand
②Film shaft for under-film
③Signboard
④Emergency stop button
⑤Laminate roll
⑥Film shaft for release paper
⑦Laminate film shaft
⑧Brake
⑨Operation panel
⑩Roller UP-DOWN lever
Main Body of ROSE-63CL
Name of Each Part

8
About Laminate Film
Before Processing Laminating
There are two types of laminate film including 「roll type」and 「pouch type」.
This product uses 「cold roll film」type.
※ 「Pouch type」and 「hot roll film」cannot be used.
Thickness (μ)Thickness of the laminate film is selected according to the use.
Thickness of the cold roll film used by this product ranges from 20 μto 300 μ.
Size of Branch Pipe
(Inner Diameter)
Size of installable paper tube differs according to the laminate structure.
This product uses a 3-inch (about 77 mm) branch pipe.
Type of Roll Film
Hot roll film
Apply heat to melt glue and attach the film.
Cold film
Parting paper (release paper) is attached on the surface applied with glue.
Release the film with the Re-winding device and compress with the roller for use.
Precautions for Handling Laminate Film

Do not place the laminate film in places with high temperature and humidity.
When lamination is not being done, store the film on the exclusive film shelf or in a box.
Use film appropriate for the laminator.
If a problem is found in the
film before use, do not use and contact the store. Reckless use may result in
failure of the laminator.

9
Paper core of release paper Laminate film
Install the laminate film same as underfilm,
and adjust center of it by referring to the scale of shaft.
【２】Install the laminate film and paper core of release paper
Insert the underfilm to the underfilm shaft and set the shaft to the machine.
【１】Install the underfilm
Installation and Processing of Cold Laminate Film
Cold Laminate Processing
Be sure to take care of convex part of the bracket and shaft.

10
①Turn on the power switch in the back of the machine.
②Turn the handle to the left side and pull down the laminate roller.
③Insert the test scripts toward the laminate roller for test laminating processing.
Adjust the wanted speed using speed control dial.
If wrinkles are formed in the processing material, set the film again or,
adjust the pressure or speed again.
④After completion of test laminate processing, start to laminate original scripts.
■In case using low temperature function
①Turn on the heater switch which is in the most right in operation panel.
When turning on the button, heater LED is lit up and lump in the left part of the machine
is illuminated.
②Press the Set button and set the adequate temperature 0 ～ 60 ℃.
When present temperature reaches set temperatur, Prepare LED is lit up and
lump in the left part of the machine is extinguished.
This mode means ready for laminate processing.
After test laminate processing, start to laminate original sctripts.
【４】Perform laminate processing
③Turn the handle and pull down the laminate roller.
※When using winding device,attach finish material with sticky tape.
Laminate film
Release paper
Insert Direction
Underfilm
Figure seen from right side
①Underfilm is passed through, Signboard→Laminate roller→Winding device
②Laminate film is passed through Laminate roller and set release paper on the paper core.
【３】Install the laminate film by referring to the figure below

11
Maintenance
This product is composed of many rollers, and they must be cleaned according to usage.
The laminate can be maintained in desirable state by cleaning the rollers.
Clean each roller since rollers have paper scraps and dusts attached.
Cleanly wipe the paper tube holder using soft and dry cloth or wipe the contaminated part using cloth with water
completely squeezed out. Here, applying force on wiping or cleaning with materials other than cloth can rip or damage
the pipe.
After using the product, cover the main body with a large cloth to avoid dusts from entering.
Cover the product with cloth after use
Cleaning of Branch Pipe Holder
Cleaning of Roller
Caution
The roller must be stopped when cleaning.
Do not clean the roller using hard objects such as steel wool. They can damage the roller.
Do not apply force on the roller for long time.
Do not clean using thick paper, which is sometimes seen in pack type laminato
r. Thick paper can block the
device and result in damage or failure.
Likewise, do not clean using thin paper. Paper can roll into the roller and the roller cannot be used.

12
Troubleshooting
The following measures are taken for troubleshooting.
Insert outlet plug and check power switch
This product is used at AC240V . Make sure that the outlet plug is correctly connected.
Check that the power switch on the back of the main body is turned on.
If power cable is disconnected, it must be replaced. Contact our company or store.
Heater or light projector is used nearby or long drum (cord reel) is used
If such objects are in use, use power from a different system.
If a drum is used, remove the drum before connecting.
Overload
Motor protection circuit may be functioning.
First remove power supply and wait for 10 seconds before resupplying power.
Abnormal noise from the motor
If an abnormal noise is created by the motor, saw-tooth wheel is damaged or screw is loose.
Contact our company or store.
There is a problem in wiring
Contact our company or store.
PCB malfunctions because of static electricity generated inside the machine
Turn the power off and then turn it on again.
Laminate film and under-film are not installed properly
Refer to P 9 ~ 10 of this document to install them properly.
Tension is too weak
Strengthen tension.
The machine is slanted
Reinstall it on a flat surface.
Is the script too thick?
Thickness of the script that can be processed by this product is 30 mm,including thickness of the film. If a thicker material
is inserted, the roller may not rotate or get damaged. Do not try to process anything thicker than the regulated thickness.
Even if thickness is within 30mm, do not insert hard materials like metals.
Is film or script rolled into the roller?
If the script remains in the insertion hole, press reverse button to pull the script out. Do not pull it too strong because
excessive pulling can cause failure of the machine.
If the script is not caught in the insertion hole, contact our company or store.
Processing material cannot be inserted
·
does not come out
Wrinkles are formed in the processing material
Product malfunctions or power is immediately turned off
Power does
not turn on
·
machine does not function

13
※ Details in this document can be changed without notice to make improvements on the product.
Max.laminating width
Max.substrate thickness
Paper tube size
Max.laminating speed
Heating system
Processing temperature
Roller clearance
Power requirement/consumption
Size（W×D×H）
Weight
1520 mm
23 mm
3 inch
6.0 m/min
Infrared inside heating system
0 ～ 60℃
Manual non step settings
AC220V 1400W
130kg
Product Specification
Others
1880×680×1140 (mm)