Larson Electronics LEDLB-4-IR User manual

QUICK DISCONNECT
DEUTSCH CONNECTOR
LEDLB-4-IR
IR LED Light Emitter
12 watts - 4 LEDs - 90'L X 70'W Beam - 9-42 Volts DC
Instruction Manual
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE LEDLB-4-IR MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL CODE AND
ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOTINSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
INFRARED LIGHT MAY CAUSE DAMAGE TO EYES IN VERY INTENSE CONCENTRATIONS.
RISK OF EYE DAMAGE AT SHORT DISTANCES. TURN LIGHT SOURCE OFF BEFORE SERVICING.
The Larson Electronics LEDLB-4-IR LED Light Bar offers high infrared light output and a compact profile combined with
versatile mounting and power options. This IP67 rated IR LED light bar is waterproof to one meter and produces 750
lumens of infrared light while drawing only 12 watts of power @1 amp from a 12 volt electrical system. This light can run
on any voltage from 9 to 42 volts and produces an infrared light beam that can only be seen through the use of night
vision goggles. 750Nm, 850Nm or 940Nm versions. This light provides a compact and powerful infrared lighting solution
that is ideal for use in commercial and industrial security applications as well as military environments.
Mounting
This fixture offers aluminum mounting blocks which slide within the
aluminum housing to allow users to adjust their positioning to match
existing or user drilled mounting holes. Each aluminum mounting
block has an integrated rubber bushing to absorb vibrations and
shocks. To secure the lights in place, simply slide the mounting bolts
through the aluminum mounting block and rubber isolator, through to
the mounting surface, then secure the bolt with a locking nut on the
opposite side of the mounting surface. This mounting system
enables mounting to flat or round surfaces and allows for minimal 7
degrees of flexibility of angle placement of the light. In this LED
emitter light bar model, an additional mounting option is provided.
The adjustable, shock insulated mounts are attached to a simple,
inverted u-bracket type mount. The LED light bar can then be
mounted via a single 3/8 bolt through the center of the bracket. To
adjust, loosen bolts on either side just enough to adjust light head.
Tighten bolts once desired position is achieved.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
POWER
Connect power to power supply outputting low voltage between 9-42 volts DC.
This variable voltage allows greater versatility without affecting light output.
Ensure deutsch connectors are properly connected.
DETACHABLE CORDS
•Cordis attached via a weatherproof 2-pinDeutsch connector.
•The cord is detachable by depressing the tab on the top of the connectors.Thisenables the operator to remove
and store the light while leaving the cordconnected to the power source.
•Additionalor replacement cords canbe ordered from our website. Contact us or visit LarsonElectronics.com for more
information.

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
LEDLB-4-IR
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before
performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void
the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine
checks to be made on a yearly basis. Frequency of use and environment should determine this. It is
recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric performance.
Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid
cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The LEDLB-4-IR is designed to provide years of reliable performance. Should the need for replacement parts arise,
please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.