Larson Electronics HAL-SL-10-20X-LED User manual

HAL-SL-10-20X-LED
200ft Hazardous Location LED String Lights
10 Lamps - Non-Metallic - Chemical Resistant - CID2
Instruction Manual
Thank you for your purchase of the Larson Electronics HAL-SL-10-20X-LED string lights.
WARNING
TO AVOID THE RISK OFFIRE, EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTED AND MAINTAINED BY A QUALIFIED ELECTRICIAN ONLY, IN ACCORDANCE WITH ALL
APPLICABLE ELECTRICAL CODES.
TO AVOID ELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTEDTOA WIRING SYSTEM WITHAN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
The HAL-SL-10-20X-LED from Larson Electronics is an Explosion Proof 200` LED String Light Set that is UL Listed Class I
Division 2 Groups A, B, C and D and is ideal for temporary work lighting and inspection activities in hazardous locations
requiring explosion proof protection. This 100 watt explosion proof LED string light set from Larson Electronics produces a
total combined output of 10,500 lumens of bright white light.
MOUNTING
USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OFTHIS DEVICE. WHEN EXTENSION
CORD IS CONNECTED TO A POWER SOURCE IN HAZARDOUS AREA, PLUG AND MATCHING RECEPTACLE MUST
BE SUITABLE FOR HAZARDOUS LOCATION INVOLVED. IMPROPER USE OF THIS DEVICE, ASSOCIATED PLUG,
RECEPTACLE, AND CORD CAN LEAD TO SERIOUS INJURIES OR DEATH TO PERSONNEL.
PERIODIC INSPECTION OF THE RECEPTACLE AND CORD IS NECESSARY.
THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, ORANY SEVERE ABRASIONS, AND IFANY ARE
FOUND, THE CORD MUST BEREPLACED BEFORE RESUMING USE OFTHE UNIT.
ELECTRICAL POWER SUPPLY MUST BE “OFF” BEFORE AND DURING INSTALLATION ANDMAINTENANCE.
INSTALLATION ANDMAINTENANCE PROCEDURE MUST BE PERFORMED BY A TRAINED AND COMPETENT
ELECTRICIAN.
IF ANY PARTS OF THE RECEPTACLE OR PLUG APPEAR TOBE MISSING, BROKEN, ORSHOW SIGNS OR
DAMAGE, DISCONTINUE USE IMMEDIATELY. REPLACE WITH THE PROPER REPLACEMENT PART(S) BEFORE
CONTINUING SERVICE.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
The HAL-SL-10-20X-LED from Larson Electronics is comprised of 10 LED
work lights equipped with hanging eye-bolts or quick links attached to the rear
mounting plate of each light. Open the eye bolt on each light and hang in the
desired location as needed, closing each eye bolt securely once the light is in
the desired location. The receptacle at the end of the string is also equipped
with a hanging eye-bolt that facilitates mounting in the same way. This allows
the user to attach another string light if needed for added distance, or any tools
rated for the same voltage and equipped with a compatible explosion proof
plug. See below for specifics on operating the explosion proof receptacle and
plug within the hazardous area.

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
HAL-SL-10-20X-LED
WIRING
We strongly encourage a licensed electrician install this product, in all locations, especially in outdoor areas where
weatherproofing may be required.
Warning: Check product label for correct input voltage!
This unit comes pre-wired from factory with the selected cord cap. Take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the unit. All outdoor installations and indoor
installations near a wet location require the use of a GFCI device for safety, according to the National Electrical Code®
(NEC). Ensure the unit is properly grounded. Follow all applicable local and national electrical and building code when
installing to maintain safety within the hazardous area. This explosion proof LED string light is equipped with a 25 foot
whip of 16/3 chemical and abrasion resistant SOOW cord that is fitted with an explosion proof cord cap for easy
connection to explosion proof outlets. Plug option is selected when ordering, check product labels for specifications
before connecting to power source.
**PLEASE NOTE** voltage ratings on plugs and outlets are MAXIMUM voltage. For low voltage applications, proper
voltage must be applied to the outlet or damage to the light fixture will occur.
Position device near work area for operation. Run cable to nearby power source outputting the correct voltage as
identified on the product label. Insert and twist-lock explosion-proof plug into a compatible receptacle within the
hazardous environment. See plug operation below.
PLUG OPERATION
Electrical connection between plug and compatible receptacle is accomplished after plug fully inserts into receptacle and
is rotated clockwise.
1. Lift receptacle door and locate polarization on mating plug pin and receptacle face. Insert plug straight all
the way into receptacle until it cannot go further.
2. Rotate plug clockwise limit (37º), this closes internal contacts and completes circuit. This also mechanically
locks plug into receptacle so it cannot be pulled out.
3. To remove plug, push plug inward and turn to counterclockwise, pull plug straight out.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
OPERATION
The lamps are“instant-on” and will illuminate once power issupplied.
LAMP REPLACEMENT
1. Loosen and remove guard (Turn counter-clockwise).
2. Unscrew globe (Turn counter-clockwise).
3. Remove and replace bulb with matching lamp.
4. Inspect gasket(s). If worn or damaged, it must be replaced to insure watertight seal.
5. Screw globe completely onto lamp base (Turn clockwise).
6. Replace guard (Turn clockwise).
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the
life of the equipment. Perform visual, mechanical and electrical inspections on a regular basis. We
recommend routine checks to be made on a yearly basis. Frequency of use and environment
should determine this. It is recommended to follow an Electrical Preventive Maintenance Program
as described in NFPA 70B: Recommended practice for Electrical Equipment. Always check for
damaged or worn out parts before using the device. Inspect for good working condition prior to
storage and before re-use.
REPLACEMENT PARTS
The HAL-SL-10-20X-LED is designed to provide years of reliable performance. Should the need
for replacement parts arise, please contact Larson Electronics.