Larson Electronics HALD-EMG-24-1X150LED-V3 User manual

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 4
Low Profile Explosion Proof Emergency LED Light
2x2 Lay-In Troffer - Class I, Divisions 1 & 2, Class II Divisions 1 & 2 - Paint Spray
Booth - 90 Minute Emergency Backup
Instruction Manual
Thankyou for your purchase of the Larson Electronics HALD-EMG-24-1X150LED-V3.
\
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE HALD-EMG-24-1X150LED-V3 MUST BE WIRED IN ACCORDANCE WITH NATIONAL
ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING
TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL
APPLICABLEELECTRICAL CODES.
TO AVOIDELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
HALD-EMG-24-1X150LED-V3

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 4
WARNING
To avoid the risk of fire, explosion,or electric shock, this product should be installed, inspected, and maintained by a
qualified electrician only, in accordance with all applicable electrical codes.
To avoid electric shock:
• Be certain electrical power if OFF before and during installation and maintenance.
• Luminaire must be connected to a wiring system with an equipment-grounding conductor
To avoid explosion:
• Make sure the supply voltage is within the luminaires’ voltage rating.
• Ensure the marked T rating is less than the ignition temperature of the Hazardous Atmosphere.
• Do not operate in ambient temperatures above those indicated on the Luminaire nameplate.
• Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.
• Substitution of components may impair suitability for Class I, Division 2, Class II Division I.
• Do not disconnect equipment unless power has been switched off or the area is known to be non-hazardous.
• Do not let the power cord touch hot surfaces.
• Do not mount near gas or electric heaters.
• Equipment should not be mounted in locations and at heights where it will not be subjected to tampering by
unauthorized personnel.
• The use of accessory equipment is not recommended by the manufacture and may cause an unsafe condition.
• Do not use this equipment for other than intended use.
The technical data indicated on the luminaire are to be observed.
• Changes to the design and modifications of the luminaire are not permitted
• Only genuine replacement parts are to be used when unforeseen maintenance is required. Consult the factory
at www.larsonelectronics.com or an authorized representative.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as
shown in thediagram 
Secure each pair of wires according to the diagram. Utilize a junction box
or similar device and take precautionary steps for
weatherproofing all connectionsif installed in alocation where
water may come in contact with the unit. Ensurethe unit is properly
grounded and that wiring is done according to all local and national
electrical/building codes.
The Larson Electronics HALD-EMG-24-1X150LED-V3 Hazardous Area LED Emergency Light Fixture is designed to
provide operators with a powerful and energy efficient alternative to traditional hazardous location luminaries and is
equipped with an added battery backup providing 90 minutes of emergency runtime. This LED panel mount fixture is ETL
listed Class I Divisions 1 & 2, Class II Divisions 1 & 2, and is approved for use within paint spray booths. Cree LED
technology and compact design makes this lamp an excellent replacement upgrade option for paint booths and hazardous
locations where flammable chemical/petrochemical vapors are present.
WIRING
This unit comes preconfigured with cord whip and selected color temp. Once mounted, plug cord into compatible
receptacle with correct voltage. Fixture available in 100-277 Volts AC, 50/60Hz or 11-25 Volts AC/DC and are not
interchangeable. Please check product nameplate for correct voltage!
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz
except those factory ordered with low voltage 11V to 25V AC/DC.
WARNING: CHECK NAMEPLATE FOR
PROPER VOLTAGE. DAMAGE FROM
IMPROPER VOLTAGE WILL VOID
WARRANTY. FIXTURE AVAILABLE IN
VARIOUS VOLTAGES SELECTED
UPON PURCHASE.
HALD-EMG-24-1X150LED-V3

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 3of 4
MOUNTING
This fixture offers recessed panel mounting. Fixture is not intended to be suspended.
1. Make sure power is turned off at the source to the location at
which you are installing the fixture.
2. Remove existing troffer if applicable.
3. Place the troffer in the drop-ceiling or flat surface cut-out. If
utilizing drop ceiling installation, operators may choose to
penetrate the flanges of the fixture to secure to the ceiling.
When installing on flat surface cutouts, operators will be
required to drill holes in the fixture flange to secure the fixture
to the surface. Use minimum of 3/8" anchor bolts to secure the
fixture to flat surfaces. When drilling holes, ONLY drill holes in
the outer flange of the fixture, minimum 2" distance between
LED assembly and drilled holes. Drilling holes for anchor bolts
does not void certification.
4. Using approved wire, connect power supply to the wire leads
on back of the fixture inside of 3/4" rigid conduit. Secure the
3/4" conduit to the back of the 3/4" NPT hub provided on the
back of the light fixture. Make remaining electrical connections
within a junction box that is approved for the environment
where the light fixture is being installed. This light fixture
requires a seal-off within 18" of the connection point on the
back of the fixture. Refer to wire diagram. All local and national
electrical/building codes must be followed when installing this
fixture in hazardous areas. If unaware, contact local authority.
5. When complete, ensure voltage matches fixture nameplate
and return power back to the source.
Installation is complete.
HALD-EMG-24-1X150LED-V3
BLACK (120/277 VAC UNSWITCHED)
WHT/RED (120/277 VAC SWITCHED)
Note: Make sure the
necessary branch circuit
wiring is available. An
unswitched source of
power is required.The
unswitched and switched
power sources must be
fed from the same
branch circuit.
WHITE (NEUTRAL)
WALL
SWITCH
AC
BALLAST/DRIVER
WITH LAMP
TEST
SWITCH
BACKUP
MICRO INVERTER
VIOLET
BROWN
CHARGING
INDICATOR
LIGHT
ORG/BLK (AC BALLAST/DRIVER HOT 120/277 VAC)
YEL/BLK (AC BALLAST/DRIVER NEUTRAL)
Note:Wire AC electronic
ballast according to
manufacturers
installation instructions.
INVERTER
CONNECTOR
RED WHITE
WIRING DIAGRAM
WARNING: CHECK NAMEPLATE FOR
PROPER VOLTAGE. DAMAGE FROM
IMPROPER VOLTAGE WILL VOID
WARRANTY. FIXTURE AVAILABLE IN
VARIOUS VOLTAGES SELECTED
UPON PURCHASE.

Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 4 of 4
HALD-EMG-24-1X150LED-V3
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The HALD-EMG-24-1X150LED-V3 is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
MAINTENANCE
Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before
performing maintenance.
Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void
the warranty.
1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine
checks to be made on a yearly basis. Frequency of use and environment should determine this. It is
recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:
Recommended practice for Electrical Equipment.
2. The lens should be cleaned periodically as needed to ensure continued photometric performance.
Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid
cleaner.
3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or
contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.
4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.