Larson Electronics EPL-TL-1X10W-C-DF-PA User manual

EPL-TL-1X10W-C-DF-PA
Larson Electronics, LLCPhone: [phone] Fax: [phone]www.larsonelectronics.com
1 of 4
Explosion Proof Signal Light w/ Audible Alarm
C1D1 / C2D1 - Strobe & Steady Burn - Multi Color
Instruction Manual
Thankyou for your purchase of the Larson Electronics EPL-TL-1X10W-C-DF-PA.
WARNING:
READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CRITICAL SAFETY INSTRUCTIONS:
•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY
RELEVANT LOCAL BUILDING CODES.
•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL
SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.
•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP
OBJECTS. SUITABLE FOR DAMP LOCATIONS.
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE EPL-TL-1X10W-C-DF-PA MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
WARNING
TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,
INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL
APPLICABLEELECTRICAL CODES.
TO AVOIDELECTRIC SHOCK:
•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.
•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING
CONDUCTOR.
TO AVOID EXPLOSION:
•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.
•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS
ATMOSPHERE.
•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT
NAMEPLATE.
•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR
DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.
•ALL FASTENERS SHOULD BE PROPERLY SEATED.
The EPL-TL-1X10W-C-DF-PA Class 1 Division 1 and Class 2 Division 1 LED Signal Light with Audible Horn from
Larson Electronics is approved for use in hazardous environments where explosive and flammable gases, vapors,
and dusts exist or stand a potential to exist, as well as wet locations and marine environments. This explosion proof
signal stack light light offers both strobing and steady burn signal operations within industrial refueling stations and
processing status indications in manufacturing facilities.

EPL-TL-1X10W-C-DF-PA
Larson Electronics, LLCPhone: [phone] Fax: [phone]www.larsonelectronics.com
2 of 4
WIRING
Standard pigtail(flying leads) wiring
We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas
where weatherproofing may be required. Universal voltage driver permits operation at 120/240V AC or 24V DC.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown
in thediagram 
Secure each pair of wires according to the diagram. Utilize a junction box or
similar device and take precautionary steps for weatherproofing all
connections if installed in a location where water may come in contact with the
unit. Ensure the unit is properly grounded and that wiring is done according to
all local and national electrical/building codes.
Low Voltage DC
Connect power to power supply outputting low voltage between 9-42Volts DC.
This variable voltage allows greater versatility without affecting light output. Ensure
deutsch connectors are properly connected (If applicable)
MOUNTING
Mounting is provided by a heavy gauge aluminum base with predrilled holes designed to be bolted to walls and flat surfaces
for permanent and secure attachment.
OPERATION
The Strobe/Steady Burn settings for the light can be toggled between each other. There is a 2-position switch that
allows the user to toggle either the Strobe setting or the Steady Burn setting.
INSTALLATION
•Do not install fixture in any classified location where the marked operating temperature exceeds the ignition
temperature of the hazardous atmospheres.
•Consult fixture nameplate for the suitability ambient temperature shown on the nameplate.
•Refer to fixture nameplate for minimum supply wire temperature rating.
•Verify that the supply voltage agrees with fixture rating as indicated on nameplate.
•All local and national electrical/building codes must be followed when installing this fixture. For code interpretation,
consult your local authority.
•Product must be intact and all cap threads fully engaged. Do not use if glass is cracked or damaged.
We strongly recommend that only a licensed electrician install this product. WARNING: Make sure that the power is
disconnected before installing. This fixture is heavyand must be mounted toa surface that can structurally support the
load. Secure the unit firmly to the surface.Failing to comply can result in breakage, allowing the fixture tofall, which can
cause serious injury or death.
It isstrongly suggested to use two licensed electricians to proceed with the final mounting of the fixture toavoid any
possible personnel injury or damage to the fixture. Depending on mounting height and scaffolding, a hydraulic man–lift or
two good quality ladders should be used.
WARNING: Check the fixture label toensure correct input voltage and frequency!
There are mounting holes on either side of the unit for surface mounting to a wall, ceiling or any flat surface. Mount the
unit in any location except hornskyward.
Run 3/4" conduit tothe junction box and wire the unit according to the wire diagram. Wire the horn to your desired sound
according to the wire diagram. Be sure to follow allsafety protocols and codes for the location.
Do not connect hornwires to line voltage. Use onlyvoltage specified on product nameplate.

EPL-TL-1X10W-C-DF-PA
Larson Electronics, LLCPhone: [phone] Fax: [phone]www.larsonelectronics.com
3 of 4
MAINTENANCE
There are no serviceable parts inside the fixture. However, itis good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the unit and be sure the fixture iscool to the touch.
•Use a non-abrasive cleaning solution to clean the fixture.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The EPL-TL-1X10W-C-DF-PA is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
[e-mail] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

MODEL EPSN-HRN-PA
LARSON ELECTRONICS, LLC
9419 US-HWY 175
KEMP, TEXAS 75143
MODEL EPSN-HRN-PA
EXPLOSION PROOF SIREN
INSTALLATION INSTRUCTIONS