Larson Electronics LEDLB-12E-F-M-1227 User manual

LEDLB-12E-F-M-1227
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
1of 2
LED Machine light - 2, 150lbs. Magnetic Bases - 120'L x 100'W Beam
Instruction Manual
Thank you for your purchase of the Larson Electronics LEDLB-12E-F-M-1227 series LED machine light. This
light is completely assembled, tested and ready for installation when shipped from the factory. Please follow
the steps below in order to operate and maintain this product.
IMPORTANT
READ CAREFULLY BEFORE OPERATING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. IF
UNSURE ABOUT ANY PART OF THESE INSTRUCTIONS, CONSULT A QUALIFIED ELECTRICAL PROFESSIONAL.
WARNING: OPERATE ONLY AT THE VOLTAGE LISTED ON THE PRODUCT. DO NOT OPERATE IN CLOSE PROXIMITY OF
COMBUSTIBLE OR FLAMMABLE MATERIALS. NEVER LOOK DIRECTLY AT LIGHT WHEN ON. DO NOT SHINE LIGHT INTO THE
FACE OF SOMEONE ELSE.
WARNING: CONSULT A QUALIFIED ELECTRICAL PROFESSIONAL/ELECTRICIAN TO INSTALL THIS DEVICE IN
ACCORDANCE WITH APPROPRIATE LOCAL AND NEC CODES AND REGULATIONS.
WARNING: DEVICE IS SUITABLE FOR INSTALLATION IN WET LOCATIONS; GFCI PROTECTION RECOMMENDED.
WARNING: ALTHOUGH FIXTURE IS WATERPROOF, IT IS NOT DESIGNED OR INTENDED TO BE SUBMERGED.
WARNING: DO NOT ALLOW LINE VOLTAGE WIRES TO BECOME SUBMERGED!
•IP68 RATED; SUITABLE FOR WET LOCATIONS (ALTHOUGH FIXTURE IS WATERPROOF, IT IS NOT DESIGNED OR
INTENDED TO BE SUBMERGED).
•ALL OUTDOOR INSTALLATIONS AND INDOOR INSTALLATIONS NEAR A WET LOCATION REQUIRE THE USE OF A
GFCI DEVICE FOR SAFETY, ACCORDING TO THE NATIONAL ELECTRICAL CODE® (NEC).
•KEEP AWAY FROM FLAMMABLE OBJECTS. DO NOT POSITION WITHIN ONE (1) INCH OF ANY COMBUSTIBLE
MATERIALS.
•IF DROPPED OR DAMAGED, THE UNIT MAY NO LONGER BE WATERPROOF AND SHOULD BE REPLACED.
•TO AVOID HAZARDS TO CHILDREN, ACCOUNT FOR ALL PARTS AND DESTROY PACKING MATERIALS.
•PEOPLE WITH PACEMAKERS SHOULD CONSULT THEIR PHYSICIAN(S) BEFORE USE. ELECTROMAGNETIC FIELDS
IN CLOSE PROXIMITY TO HEART PACEMAKER COULD CAUSE PACEMAKER INTERFERENCE OR PACEMAKER
FAILURE.
•KEEP FINGERS AWAY FROM MAGNET WHEN MOUNTING AS INJURY COULD OCCUR.
INSTALLATION
MOUNTING
Mount via the two, 100lb. magnets. This allows for easy fixture
placement and removal. Please note: The magnetic base on this
unit increases the units` overall height.
When removing, do not drag the magnets to disconnect, as it
may scratch the surface/paint. Each magnet provides 200lb. grip
magnetic force.
WIRING
Once mounted, check to ensure the deutsch connector from the transformer is plugged into the back of the
light. Run cord and transformer near power source. Connect the transformer into the proper voltage listed on
its product label. Improper voltage could cause the unit to fail, voiding warranty. The light is “instant-on” and will
turn on once power is supplied.
Voltage: 110V with transformer. 9-42 VDC Without transformer.
TRANSFORMER
DEUTSCH CONNECTOR
MAGNETS
CORD CAP
DEUTSCH CONNECTOR

LEDLB-12E-F-M-1227
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com
2of 2
LIGHT ADJUSTMENT
The light can adjust up or down by loosening the screws on each side of the
light. Loosen both screws to move the light up or down and tighten when
complete. Tighten all bolts once desired position is achieved.
Light can be easily readjusted by lifting off the metal surface and re-attaching
to the desired position on the magnetic surface.
MAINTENANCE
If the lens becomes dirty, wipe down with a mild soap and water solution.
It is recommended to occasionally inspect the unit for any defects and to ensure the cable is not frayed and is
gripping tightly in all points of cable contact.
TROUBLESHOOTING
Refer to the guide below or contact the manufacturer if the fixture does not function properly.
Is the correct line voltage supplied?
Is the line active?
Is the Deutsch connecter properly attached?
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS. SHOULD FURTHER
INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT [e-mail] OR BY PHONE AT
1-800-369-6671 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.