Larson Electronics TPM-2XLEDEQ-4X3-CPR User manual

TPM-2XLEDEQ-4X3-CPR
120W LED Pole Light
(2) LED Lamps - 3' to 8.5' Adjustable - 9-64V DC
Instruction Manual
IMPORTANT
READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. THE TPM-2XLEDEQ-4X3-CPR MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL
CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.
WE STRONGLY ENCOURAGE ONLY A LICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS
PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,
CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.
WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE
INSTALLATION OR PERFORMING ANY MAINTENANCE.
RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.
RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.
RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.
The Larson Electronics TPM-2XLEDEQ-4X3-CPR LED Pole Light is a pole lighting solution with outdoor and rugged
applications. This 120-watt unit consists of two high output LED fixtures, which are capable of emitting 8,400 lumens of
white light. The telescoping pole is adjustable at heights between 3 and 8.5 feet. Operators can manage power
connections seamlessly using a 20` wiring harness with a weatherproof quick disconnect.
MOUNTING AND SETUP
The adjustable telescoping pole is designed to be mounted to any vertical surface via an
included mounting plate with four pre-drilled mounting holes. Users can simply attach the
mounting plate to a wall, trailer, the exterior of boat cockpits etc, then slip the pole into the
bracket and lock it into place using the T-handle screw. Once positioned, the aluminum pole can
be collapsed to 3 feet and extended to 8.5 feet by unlatching the locking brackets, extend the
pole to the desired length, and lock the brackets to hold in position. The top of the pole is fitted
with an aluminum mounting plate holding the two LED lamps. Each lamp can be rotated or tilted
to the desired position. Use the screws on the sides of the lamps for vertical adjustments, and
the bolt through the bottom bracket for horizontal adjustments.
WIRING
The TPM-2XLEDEQ-4X3-CPR comes with a 20` 16/2 wiring harness, which features a
weatherproof quick disconnect between the light and harness. Attach the harness to the lights
via the Deutsch connectors as shown.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 1of 2
•Cordis attached via a weatherproof 2-pinDeutsch connector.
•The cord is detachable by depressing the tab on the top of the connectors. This
enables the operator to remove and store the light while leaving the cordconnected to the
power source.
•Additionalor replacement cords canbe ordered from our website. Contact us or visit
LarsonElectronics.com for more information.
QUICK DISCONNECT
DEUTSCH CONNECTOR
Once the harness is connected, complete the connections as appropriate for the cord
option chosen when ordering.
FLYING LEADS
We strongly encourage a licensed electrician install this product, in all locations,
especially in outdoor areas where weatherproofing may be required.
Warning: Check product label for correct input voltage!
Attach supply line wires to the appropriate light fixture wires as shown in the
diagram 

TPM-2XLEDEQ-4X3-CPR
BATTERY CLAMPS OR RING TERMINALS
Complete connection to battery outputting voltage within the fixture's rating, following all local and national electric
codes, and taking precautionary steps for weatherproofing all connections if installed in a location where water may
come in contact with the unit. All outdoor installations and indoor installations near a wet location require the use of a
GFCI device for safety, according to the National Electrical Code® (NEC). Ensure the unit is properly grounded.
CIGARETTE PLUG
Mate cord cap with compatible receptacle outputting voltage within the fixture's rating.
Larson Electronics, LLC Phone: [phone] Fax: [phone] www.larsonelectronics.com 2of 2
THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.
SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT
SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.
PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.
MAINTENANCE
There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the
fixture for proper function.
•Disconnect power running to the lamp and be sure the fixture is cool to the touch.
•Use a non-abrasive glass cleaning solution to clean the lens.
Note: It is not necessary to open the fixture and clean or touch the LED’s.
USE AND CARE
Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.
Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of
children when not in use.Inspect for good working condition prior to storage and before re-use.
REPLACEMENT PARTS
The TPM-2XLEDEQ-4X3-CPR is designed to provide years of reliable performance. Should the need for replacement
parts arise, please contact Larson Electronics.