LAZBOY 50106M User manual

Mid Back Polyurethane Chair
Assembly Instructions
Model 50106M
300 lbs
Designed to be comfortable,
andbuilt to stay that way.

2
D
C
B
A
EF
IJ
GH
K
Allen Key
Quantity: 1
PARTS
Casters
Quantity: 5 Star Base Quantity:1Gas Lift Quantity: 1 Seat Plate Quantity: 1
Arms
Quantity: 2
SeatCushion
Quantity:1
Back Cushion
Quantity: 1
1” Screws
Quantity: 4
1-1/4”Screws
Quantity: 4
WARNINGS
1. This product should be used by only one person at a time.
2. Do not use this chair unless all bolts, screws and knobs are securely tightened.
3. Save the hexagonal wrench. Check that all bolts, screws and knobs are tight every three months or as needed.
4. Dispose of packing material properly. Do not use the plastic cover as a head covering. It may cause suffocation.
5. Do not use the chair as a stepladder.
6. To clean the product, use only a clean cloth. The use of chemicals or cleaning products may affect the color
fastness.
7. Use this chair for its intended purpose only.
8. The casters sold with this chair are intended for use on carpet. They are not recommended for use on tile or
hard-wood oors. Using these casters on tile or wood ooring may cause damage to the oor surface. Please
consider using a chair mat to protect your oor surfaces.
E1
E2
1-1/2” Screws with Spring Washers
Quantity: 4 Quantity:2
R
L1 L2
R1 R2
L
Arm Inserts
Arm Inserts
Quantity:2

3
B
A
B
C
Step 1
Place the star base (B) upside down and insert 5
casters (A) into the holes on the star base (B).
Step 2
Turn the star base (B) over and insert the gas
lift (C) through the center hole on top of star
base (B).

4
G
F
H
K
Step 3
Align the back cushion (G) with the seat cushion (F) and attach the back support plate onto the bottom of the seat
cushion (F) by using 1-1/4” screws (H).
*Note: Do not tighten the screws completely.

5
F
D
I
I
K
Step 4
Attach seat plate (D) to the bottom of the seat cushion (F) (with the front of the seat plate facing the front of seat
cushion). Attach by using four 1” screws (I) for the holes of the seat plate (D) and tighten the screws using allen key (K).
*Note: Tighten the screws completely.

6
E1
E2
G
F
J
K
Step 5
Insert 1-1/2" screws with spring washers (J) into arm holes attaching arms (E1 & E2) (with front of arms facing the front
of seat cushion) to sides of seat cushion (F) and back cushion (G).
*Note: Tighten all the screws completely. Remember to tighten the back support plate screws.

7
D
C
F
Step 6
Position the assembled chair upright with the seat plate facing down. Insert the gas lift (C) into the center hole of the
seat plate (D).

8
L1
L2
R1
R2
Step 7
Place the arm inserts (L1, L2, R1 & R2) into arm grooves once all screws have been tightened.

Operating Instructions
9
Function Instruction - 1
To Adjust Seat Height:
While seated, lean forward and reach under the right side of the chair to nd the handle. Lift the handle and raise
your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release handle
to lock chair at desired height. To lower the seat, lift the handle while seated. The chair will descend until the
handle is released or the chair reaches the bottom position.

10
Function Instruction - 2
To Operate Tilt Lockout:
Reach under the left side of the chair to nd the handle. Flip the handle down and lean back to allow the chair to
tilt backwards. Flip the handle up to lock the chair angle while the desired position is reached.