LAZBOY CHR10085A-C User manual

Executive Chair
ASSEMBLY
Instructions
Model: CHR10085A-C

Should you prefer to
speak with a customer
service representative,
you may call toll free :
1-855-372-2315
0-800-051-6775
U.S. 6am - 5pm PST,
U.K. 2pm -1am
2

FAILURE TO FOLLOW THESE WARNINGS
WHEN IN USE COULD RESULT IN INJURY
• Do not stand on the item or use as a step ladder.
• The piece has been tested and approved for users
weighing up to 275 lbs (125kg) per seat.
• Do not use this item unless all bolts and screws are
firmly secured and fastened.
• Check all bolts and screws every 90 days. As
necessary tighten if any are loose.
• Lift up then move. Pushing over or dragging this
product can result in an injury or cause damage to
the floor and piece.
Guidelines
3

Please read through this instruction booklet before
beginning assembly of this item.
Two adults are recommended for assembly.
• Clear out the space for assembly and lay out all
parts on Parts List, extra room will allow you to
easily determine if all the pieces are present.
• Save all packing materials until assembly is
complete to avoid accidentally discarding smaller
parts or hardware.
• Keep small parts and pieces away from children
and pets until fully assembled.
• Please check for any loose screws and tighten them
before you use.
WARNING :DO NOT LET
CHILDREN PLAY IN OR
AROUND THE UNIT DUE
TO THE POSSIBLE RISK
OF INJURY.
Pre-Assembly Preparation:
4

Parts List
Casters Star BaseGas Lift Seat Plate
D E1C
BA
1-1/2” Big Screws
M
Allen Key
SeatCushion Back Cushion
G
FI
J
Quantity: 5Quantity:1Quantity: 1Quantity: 1
Left Arm
Quantity: 1
Quantity:1Quantity: 1
Plastic Shroud
H
Quantity: 1
Quantity: 1
Quantity: 2
1” Big Screws
Quantity: 2
5
D1
D2
1” Small Screws
K
Quantity:6
1-1/4”Big Screws
Quantity:4
L
E1
Right Arm
Quantity: 1

Step 1 Step 2
Place the Star Base (B) upside down and insert 5 Casters (A) into the holes
on the Star Base (B).
Turn the Star Base (B) over and insert the Gas Lift (C) through the
center hole on top of Star Base (B).
6
A
B
C
B

Step 3 Step 4
Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front
of the seat plate facing the front of seat cushion). Attach by using 1-1/2”
Big Screws (I) for the front holes of the Seat Plate (D) and 1” Big Screws (J)
for the rear holes of the Seat Plate (D) and tighten screws.
*Note: Tighten the screws completely.
Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable
lever receivers on the underside of Seat Cushion (F) (with the front
of the levers facing the front of seat cushion). Push down the key
on the receivers to pull out the levers.
*Note: Fix the cable for the seat plate into the plastic clips
attached to the bottom of the seat cushion.
7
Disassemble the lever
Assemble the lever
Insert Push
M
I
J
F
D
F
D
D1
D2

8
Step 5 Step 6
Tighten the brackets of Arms (E1 & E2) onto the bottom of the Seat
Cushion (F) (with front of arms facing the front of seat cushion) by using
1” Small Screws (K).
*Note: Tighten the screws completely.
Align the Back Cushion (G) with the Seat Cushion (F) by
positioning the back support plate over the Seat Plate (D) with
1-1/4” Big Screws (L).
*Note: Tighten the screws completely.
MM
E2
K
R
L
R
E1
F
F
L
K
L
R
G
R
D

9
Step 7 Step 8
Put the Plastic Shroud (H) over the Seat Plate (D) (with the front of plastic
shroud facing the front of seat cushion). Align shroud posts to holes on
bottom of Seat Cushion (F) and press into position.
Position the assembled chair upright with the seat plate facing
down. Insert the Gas Lift (C) into the center hole of the Seat
Plate (D).
L
R
D
F
H
F
D
C

10
Operating Instructions
Function Instruction - 1
To Adjust Seat Height:
While seated, lean forward and reach under the right side of the chair to
find the lever. Lift the lever and raise your body up slightly to allow the
chair to rise to the desired height. Once desired height is reached,
release lever to lock chair at desired height. To lower the seat, lift the
lever while seated. The chair will descend until the lever is released or
the chair reaches the bottom position.