LAZBOY Sears Ashton User manual

Page 1 of 5
OWNER’S MANUAL
Sears Ashton Side Table
Product Code: 12779
UPC Code: 7-22938-08624-5
Date of Purchase: __ / __ / __
If you have any problems with this product, DO NOT RETURN IT TO THE STORE.
CALL OUR CUSTOMER SERVICE HOT-LINE AT
866-391-4868
8am-5pm (EST), Monday-Thursday
8am-4pm (EST), Friday.
View the expanded assortment of outdoor living product on-line at
WWW.lazboyoutdoor.com and WWW.sears.com

Page 2 of 5
WARRANTY
In order to activate your warranty please register at www.bji.com. There you can review our full warranty details
and other helpful information. Or, you may call us at 866-391-4868, 8am - 5pm (EST), Monday – Thursday, 8am –
4pm(EST), Friday.
Care and Maintenance
Be careful to never allow water to build up in frames as this will cause corrosion and freeze damage in cold climates. Wash
all frames with a solution of mild soap and water. Rinse with clean water and dry with a soft absorbent cloth towel. Frames
can be treated with a liquid wax for maximum protection against UV rays and/or salty damp air. If your set includes
cushions, slings, and/or an umbrella they may be cleaned by hand with a solution of soap and water with a clean water
rinse. (Never machine wash cushions, slings or umbrella covers as this will result in shrinkage or damage).
After cleaning cushions tip on end and allow to drip dry. (Never use a commercial or home dryer to tumble dry fabric
goods).
Do not use bleach or solvents to clean any product! This will void the warranty.
Lack of original receipt will void warranty!
CAUTION: Read all the instruction before assembly.
Failure to do so may result in faulty assembly and potential injury!
Assemble the item on a soft, non-abrasive surface such as a carpet or cardboard to avoid damaging
the item. Seek assistance to assemble bulky or heavy items.
After final alignment, make sure all bolts, nuts and nut covers are securely tightened.
Assembly Instruction:
Note: 1. DO NOT tighten completely until all bolts are in place.
2. Paint Not provided with all furniture.
PARTS LIST
Item Part Name Picture Qty
A Table Rim
1
B Table Leg
2
C Panel 2
D Connector Ring 1
E M6x20mm Hex Head
Bolt
12

Page 3 of 5
F M6 Washer 12
G Bolt Cap 12
H Hex Wrench
2
I Glass 1
Assembly Steps:
Step1: Turn the table rim (A) upside down on a soft, non-abrasive surface carefully. Attach the table
legs (B) to table top (A) with M6 x 20mm hex head bolt (E), M6 washer (F). (See Figure 1)
Figure 1
Step2: Attach one panel (C) to table leg (B) with M6 x 20mm hex head bolt (E), M6 washer (F).
(SeeFigure2)
Figure 2

Page 4 of 5
Step3: Insert the connector ring (D) to the holes in panels (C), repeat step 2 attach the other panel(C)
to table leg (B) with M6 x 20mm hex head bolt (E), M6 washer (F). Tighten all bolts with hex
wrench (H). Cover all the bolts with bolt caps (G) (See Figure 3)
Figure3
Step 4: Then turn your table right side up. Place the glass (I) on the table rim (A). (See Figure 4)
Figure 4
Now your table is ready for your enjoyment!

Page 5 of 5
WARNING:
1. Do not crawl, stand or sit on the glass table tops.
2. Do not set or lay heavy items on glass table tops.
3. Avoid extreme hot and cold items being placed on glass table tops.
4. This glass table top is produced with tempered glass which is designed to safely shatter
in small pieces when impacted or stress beyond strength limitations.