LDARC GT Series User manual

User manual and video please visit：WWW.LDARC.COM
PRODUCT>>MULTROTOR>>GT SERIES>>90/130GTI PNP
90/130GTI manual Video manual
90/130GTI
Manual
190805

-1-
Configuration
F411+OSD
4in1 20A BLheliS
0/25/100/200mW 48CH
AC2000 DUAL-CORE TRI-MODE RSSI(S-FHSS+D16 non-EU+D16 EU-LBT)
Caddx.US turtle V2(1080P)
98mm
XT1105-5000KV
2035 & 2045
11.4V 530mAh 80C(XT30)
3S(Recommend voltage)
83.7g
1080P/60fps 16:9 64G
C1200(1200TVL 1/3’COMS NTSC)
98mm
XT1105-5000KV
2035 & 2045
11.4V 530mAh 80C(XT30)
3S(Recommend voltage)
74.1g
-
133mm
XT1406-3600KV
3050
3-4S 600-800mAh
4S(Recommend voltage)
139.1g
1080P/60fps 16:9 64G
133mm
XT1406-3600KV
3050
3-4S 600-800mAh
4S(Recommend voltage)
128.4g
-
Name
FC
ESC
VTX
Receiver
Camera
Wheelbase
Motor
Prop
Battery
Voltage
Weight
Video
90GTI(HD) 90GTI(FPV)130GTI(HD) 130GTI(FPV)
The weight not include receiver,battery,prop and bumper;130GTI recommend battery LDARC 14.8V 650mAh 50C
90GTI(HD) 90GTI(FPV)
130GTI(HD) 130GTI(FPV)

-2-
Package list
90GTI(FPV)
+
+
+
+
+ +
90GTI(FPV)*1
Sticker*1 Receiver manual*1
90GTI(HD)
+
+
+
+
+ +
90GTI(HD)*1
Canopy*1
Canopy*1
Sticker*1 Receiver manual*1
Racing booth*1 Set
Racing booth*1 Set
Bumper(half surround)*1 Set
Bumper(all surround)*1 Set
11.4V 530mAh 80C*1
11.4V 530mAh 80C*1
130GTI(FPV)
+ + + +
130GTI(FPV)*1
Receiver manual*1
TPU*2 3050*10 Pairs
3050*10 Pairs
Canopy*1
130GTI(HD)
+ + + +
130GTI(HD)*1
Receiver manual*1
TPU *2 Canopy*1

-3-
BUZZER-
GND
LED STRIP
5V(BUZZER+)
TX2
VIDEO
CAM
5V
GND
VIDEO
AUDIO
VCC
GND
SIGNAL
AUDIO
5V
GND
PPM+RX2-INV
3V3
BATTERY+ RX2
5V GND
TX2
VIDEO
BATTERY+ RX2
5V GND
RX2-INV
TX2-INV
CURRENT
PWM4
GND
PWM3
GND
PWM2
GND
PWM1
BATTERY+
BATTERY+
Supply voltage is 5V
NOT invert RX1 signal input
GND
5V RX1
TX1
BETAFLIGHT
USB
Supply voltage is 3.3V
NOT invert RX2 signal input
5V
GND
PPM+RX2-INV
3V3
DSM2/DSMX
GND
5V RX1
TX1
5V
GND
PPM+RX2-INV
3V3
iBUS etc.
GND
5V RX1
TX1
5V
GND
PPM+RX2-INV
3V3
SBUS/PPM
Supply voltage is 5V
PPM or invert RX2 signal input
S.BUS and PPM receiver connection
Pin definition
DSM2 and DSMX receiver connection
iBUS receiver connection
GND
TX1
GND
VIDEO
GND
AUDIO
GNDBATTERY+
BATTERY+
Only KKT-F411(20x20)-90214 version

-4-
M4(CW) M2(CCW)
M3(CCW)
Note:pay attention to the direction of rotation
of the motor when installing the prop
M1(CW)
+-
M1
M2
M3
M4
VTX
ESC Motor
LED
AV5V GND B+ B-
BAT
CH BD PW
Frequency button Frequency button
Connect FC
CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8
5865 5845 5825 5805 5785 5765 5745 5725
5733 5752 5771 5790 5809 5828 5847 5866
5705 5685 5665 5645 5885 5905 5925 5945
5740
5362
5658
5760
5400
5695
5780
5436
5732
5800
5473
5769
5820
5510
5806
5840
5547
5843
5860
5584
5880
5880
5620
5917
Band A
Band B
Band E
Band F
Band H
Band R
Bule LED is channel (CH) indicator,flash 1~8 times mean CH-1~8.Green LED is band(BD) indicator,flash 1~6 times
mean BAND-A~F,Red is output power(PW)indicator,flash 1~3 times mean 25mW/100mW/200mW output power.
In normal working state,quickly double-click button,R/G/B sync flash mean VTX turned off,and also quickly double
-click can turn on the VTX.in normal working state,press and hold the key for 3s,only blue led flashes,now click the
key change channel(CH).press and hold the key for 3s,only blue green flashes,now click the key change band(BD) .
press and hold the key for 3s,only red led flashes,now click the key change output power(PW).

-5-
Receiver bind
AC900(S-FHSS+D16) bind,transmitter(FRSKY X9D/Futaba T18SZ)
Bind:Check receiver mode before bind,the first blink after power on indicate the setting, is S-FHSS, is D16
FUTABA S-FHSS BIND:Turn on the TX then power on AC900 while pressing the key, green LED fast blink meaning already in bind
mode, user can release the key. Bind procedure is completed and the receiver is working normally when green LED is solid
FRSKY D16(NO Telemetry) BIND:Power on AC900 while pressing the key, green LED fast blink meaning already in bind mode,
user can release the key, then set your TX into D16 bind mode. red LED solid meaning bind finished, exit TX from bind mode,
receiver’s green LED solid meaning working normally

-6-
BIND:Power on the receiver while pressing the key,green LED fast blink meaning already in bind mode,
user can release the key,then set your TX into bind mode.Green LED turn off and red LED solid mean bind finished,
exit TX from bind mode,receiver’sgreen LED solid mean working normally.
RX2A PRO Bind(S.BUS),transmitter(FLYSKY FS-i6)

-7-
5.Select ESC protocol is DSHOT600,then follow the steps to set up
(1)
(1)
(2)
(3)
(2)
(3)
Connect
MATEKF411
3.5.3- MATEKF411 -15-11-2018 13:35(stable)
BETAFLIGHT firmware allready flash before leave the factory,user just need connect PC to adjust the parameter
1.Open betaflight configuration ,then click ,select FW version
2.Click ,then click to download FW to FC, click after FW
updating finish into setting menu
3.Calibration“Calibrate Accelerometer”
4.Selected UART6,then open“Serial RX”switch and saved
Firmware Update

-8-
6.PID set
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(1)
(2)
(3) (4)
(5)
(6)

-9-
(1)
(2)
(3)
(1)
(2)
7.Mode set
7.LED set

-10-
Name
90GTI(HD) NO RX
90GTI(FPV) NO RX
90GTI(HD) AC2000
90GTI(FPV) AC2000
130GTI(HD) NO RX
130GTI(FPV) NO RX
130GTI(HD) AC2000
130GTI(FPV) AC2000
90GTI KIT
130GTI KIT
电池11.4V 530mAh 80C
电池14.8V 650mAh 50C
C1200
90GTI protector bumper(half)
90GTI protector bumper(all)
3.1 inch protector bumper(half)
Factory code
PNP.90GTI(HD).NO RX
PNP.90GTI(FPV).NO RX
PNP.90GTI(HD).AC2000
PNP.90GTI(FPV).AC2000
PNP.130GTI(HD).NO RX
PNP.130GTI(FPV).NO RX
PNP.130GTI(HD).AC2000
PNP.130GTI(FPV).AC2000
KIT.90GTI
KIT.130GTI
BAT.11.4V 530MAH 80C
BAT.14.8V 650MAH 50C
CAM.C1200
PART.90GTI PROTECTOR BUMPER(HALF)
PART.90GTI PROTECTOR BUMPER(ALL)
3.1 INCH PROTECTOR BUMPER(HALF)
Factory code
PROP.2035.4.WHITE
PROP.2045.4.WHITE
PROP.3050.3.WHITE
MOTOR.XT1406-3600KV
MOTOR.XT1105-5000KV
ESC.KK TOWER 20A
FC.F411+OSD(V2)
VTX.KK TOWER
PART.KK TOWER SCREW(3 LAYER)
PART.KK TOWER WIRE
PART.90/130GTI CANOPY
PART.90GTI BOTTOM PLATE
PART.130GTI BOTTOM PLATE
PART.90GTI PLASTIC PART
PART.TPU SMALL LANDING GEAR
PART.KK TOWER ANTENNA
Name
2035 Prop
2045 Prop
3050 Prop
XT1406-3600KV
XT1105-5000KV
4in1 ESC 20A
F411+OSD FC
VTX
3-Layer tower screw
Wire
90/130GTI Canopy
90GTI Bottom plate
130GTI Bottom plate
90GTI Plastic part
TPU small landing gear
Antenna
Product and Factory Code
1.Provide free reparation service when find the product defect after purchase.
2.Provide pay-needed reparation service when product damage because improper operation.
3.China customers please contact with the after-sales service,overseas client please contact the dealer.
PNP/RTF Test report ID :
Flight test
Transmitter functions properly
Flying in good condition
Camera OK
VTX OK
QC:
Package check
PNP
RTF
Frame
Transmitter
ID is the same
All parts of the installation
Insulating sleeves have been installed manual
Complete accessories,total packages
QC:
After Sale Service