LeapFrog Interactive Learning Easel User manual

Instruction Manual
This manual contains important information. Please save it for future reference.
Interactive Learning Easel
Interactive Learning EaselInteractive Learning Easel Interactive Learning Easel

2
INTRODUCTION
Thank you for purchasing the Interactive Learning Easel!
This 2-in-1 blackboard/whiteboard easel comes with 26
letter tiles, six shape tiles, chalk and an erasable marker. The
interactive learning panel teaches letters and encourages
creative play through drawing. The touch-sensitive pictures in
the book describe how to use the magnetic shape tiles to draw
pictures. The letter tile reader helps kids explore letter sounds,
letter writing and new words.
Board Clip
Release
Activity
Buttons
Music Button
Letter Tile Reader
Letter Tiles
Shape Tiles
Storage Tray
Off/Low/High
Volume Switch
Board Clip
Artwork Clip
Whiteboard
/Blackboard
Touch Book
Chalk
Erasable Marker

3
Connector (1)
Learning Panel (3)
A-Frame (1/2)
Connector (2) Upper Rear Leg (4)
Storage Tray (1/2)
Brace (5)
INCLUDED IN THE PACKAGE

4
Lower Rear Leg
Rear Leg Base (8)
Lower Front Leg (7)
Lower Front Leg (6)
6 Nuts
10 Screws 6 Bolts

5
• Quick Start Guide
Whiteboard/
Blackboard
26 Magnetic
Letter Tiles
6 Magnetic Shape
Tiles
3 Chalk Pieces 1 Erasable Marker

6
CAUTION:
Adult assembly required.
Small fasteners included.
CHOKING HAZARD—small parts.
Not for children under 3 yrs.
WARNING:
This product contains small magnets. Swallowed
magnets can stick together across intestines causing
serious infections and death. Seek immediate medical
attention if any magnet is swallowed or inhaled.
WARNING
All packing materials such as tape, plastic sheets, packaging
locks, removable tags, cable ties, cords and packaging screws
are not part of this toy and should be discarded for your child’s
safety.
NOTE
Please save this Instruction Manual as it contains important
information.
NOTE
Please ask us about the availability of FSC Products.

ASSEMBLY
With the Interactive Learning Easel, safety comes first. To
ensure your child’s safety, adult assembly is required.
ADULT ASSEMBLY REQUIRED:
Tool needed: Phillips-head screwdriver (not included).
Note: Numbers referenced below refer to the moulded
plastic numbers on assembly parts. See INCLUDED IN THE
PACKAGE pages for reference.
1. Locate the marking of numbers 1 and
2 on the A-Frame and on the Storage
Tray separately. Align A-Frame 1 with
Storage Tray 1 and A-Frame 2 with
Storage Tray 2. The legs will rest in
the slots until they are secured.
2. Lay the pieces face down on a flat
surface so that the back of the
Storage Tray 1/2 and the back of the
A-Frame 1/2 are facing up.
7

3. Slide Connector 1 into the slot formed
by the aligned pieces A-Frame 1 and
Storage Tray 1 with the number 1 on
Connector 1 facing up.
4. Use three Screws and your Phillips-
head screwdriver to secure.
5. Slide Connector 2 into the slot
formed by the aligned pieces
A-Frame 2 and Storage Tray 2 with
the number 2 on Connector 2 facing
up.
6. Use three Screws and your Phillips-
head screwdriver to secure.
8

7. Slide the four studs on the back of the
Learning Panel 3 into the slots on the
A-Frame 1/2. The Learning Panel 3 will
rest in the slots until it is secured.
8. Secure Learning Panel 3 to A-Frame
1/2 with two Screws on each side as
shown.
9. Snap Upper Rear Leg 4 into the top
of A-Frame 1/2 as shown with the
number 4 facing out.
10. Snap Brace 5 into the back of Learning
Panel 3 as shown with the number 5
facing up.
9

10
11. Firmly snap the other end of Brace
5into the yellow slot in the back of
Upper Rear Leg 4 as shown. (Note:
Once inserted, this piece cannot be
removed.) You have now assembled
the upper easel.
12. Lay the assembled upper easel face
down on a flat surface.
13. Fit Lower Front Leg 6 into Connector
1 with the curved side of the leg
facing down and the number 6 facing
up. Secure with two Nuts and two
Bolts, inserting the Nuts from the
bottom.
14. Fit Lower Front Leg 7 into Connector
2with the curved side of the leg
facing down and the number 7 facing
up. Secure with two Nuts and two
Bolts, inserting the Nuts from the
bottom.