LeapFrog On-the-Go Story Pal User manual

Instruction Manual
This manual contains important information. Please keep it for future reference.
91-003934-006 US

2
INTRODUCTION
Thank you for purchasing the On-the-Go Story Pal™ device!
Get ready to enter a magical world of storytelling, music
and learning!
Back Button
Micro USB
(cable not
included)
Microphone
Speaker
Off
On/Off/Mode
Selector Dial
Stories Music & Poems
LED Screen
Play/Pause
Button
Headphone Jack
(headphones not
included)
Recorded Story
Star Button
Next Button Volume Control
Sleepy Time Lullabies
Battery Door
Hand Strap

3
INCLUDED IN THE PACKAGE
On-the-Go Story Pal™ device
• Instruction Manual
WARNING
All packing materials such as tape, plastic sheets, packaging locks,
removable tags, cable ties, cords and packaging screws are not
part of this toy, and should be discarded for your child’s safety.
NOTE
Please keep the Instruction Manual as it contains
important information.
ATTENTION
Pour la sécurité de votre enfant, débarrassez-vous de tous
les produits d’emballage tels que rubans adhésifs, feuilles de
plastique, attaches, étiquettes, cordons et vis d’emballage. Ils ne
font pas partie du jouet.
NOTE
Il est conseillé de conserver ce guide des parents car il comporte
des informations importantes.
This toy is only to be connected to equipment bearing either the
following symbols: or .
Le jouet doit uniquement être connecté à des équipements
portant l’un des symboles suivants ou .
Unlock the Packaging Locks
Rotate the packaging locks 90
degrees counterclockwise.
Pull out the packaging locks
and discard.

4
INSTRUCTIONS
Battery Removal and Installation
1. Make sure the unit is turned Off.
2. Find the battery cover located
on the back of the unit, use a
screwdriver to loosen the screw
and then open the battery cover.
3. Remove old batteries by pulling up
on one end of each battery.
4. Install 3 new AA (AM-3/LR6)
batteries following the diagram
inside the battery box. For best
performance, alkaline batteries or
fully charged Ni-MH rechargeable
batteries are recommended.
5. Replace the battery cover and
tighten the screw to secure.
WARNING:
Adult assembly required for battery installation.
Keep batteries out of reach of children.
ATTENTION :
Les piles ou accumulateurs doivent être installés par un adulte.
Tenir les piles ou accumulateurs hors de portée des enfants.

5
IMPORTANT: BATTERY INFORMATION
• Insert batteries with the correct polarity (+ and -).
• Do not mix old and new batteries.
• Do not mix alkaline, standard (carbon-zinc) or
rechargeable batteries.
• Only batteries of the same or equivalent type as
recommended are to be used.
• Do not short-circuit the supply terminals.
• Remove batteries during long periods of non-use.
• Remove exhausted batteries from the toy.
• Dispose of batteries safely. Do not dispose of batteries in fire.
RECHARGEABLE BATTERIES
• Remove rechargeable batteries from the toy before charging.
• Rechargeable batteries are only to be charged under
adult supervision.
• Do not charge non-rechargeable batteries.
ACTIVATE NORMAL PLAY MODE
This product is in Try-Me mode in the packaging. To activate
normal play mode, please complete the following steps:
1. Rotate the On/Off/Mode Selector Dial
to the Off position.
2. Rotate the On/Off/Mode Selector Dial to
the Stories position to activate normal
play mode.

6
PRODUCT FEATURES
1. On/Off/Mode Selector Dial
Rotate the On/Off/Mode Selector
Dial to choose a category. Categories
include: Stories; Music & Poems; Sleepy
Time Lullabies and Recorded Story.
Rotate the On/O/Mode Selector Dial to
the O position to turn the toy off.
2. Play/Pause Button
Press to pause the story, song or poem.
Press again to play.
3. Back Button
Press to select the previous story, song
or poem.
4. Next Button
Press to select the next story, song
or poem.

7
5. Star Button
In the Recorded Story mode, follow the
audio instructions and press the Star
Button to begin recording.
In other modes, quickly press the Star
Button to hear your playlist. To save a
story/song to the playlist, press and hold
the Star Button until it beeps.
6. Volume Control
Turn the dial up or down to adjust the
volume level.
7. USB Port
To download additional free stories,
follow the instructions in the
Downloadable Content section later in
this guide.
8. Set Timer
Press and hold the Play/Pause Button for 5 seconds, then
follow the audio instructions to set the timer.
9. Automatic Shut-Off
To preserve battery life, the On-the-Go Story Pal™ will
automatically shut off after approximately 60 seconds if a
story or song is not playing. The unit can be turned on by
pressing any button.

8
ACTIVITIES
Listen to a Story, Poem or Song
Rotate the On/O/Mode Selector Dial to choose a category.
After selecting a category, press the Next Button to toggle
through the story options. Stories will play automatically after
their titles are announced.
Stories
1. The Tale of Peter Rabbit
2. The Little Mermaid
3. The Tortoise and the Hare
4. Peter Pan
5. Jack and the Beanstalk
6. The Elves and the Shoemaker
7. Rapunzel
8. The Midas Touch
9. The Three Little Pigs
10. The Ugly Duckling
11. The Wind and the Sun
12. Puss in Boots
13. Briar-Rose
14. The Legend of John Henry
15. The World of Dinosaurs
16. Beauty and the Beast
17. The Emperor’s New Clothes
18. Cinderella
19. Rumpelstiltskin
20. The Gingerbread Man
21. Robin Hood and the Golden Arrow
22. Hansel and Gretel
23. Paul Bunyan and Babe the Big Blue Ox
24. The Little Red Hen

9
25. Chicken Little
26. The Three Billy Goats Gruff
27. The Lucky Drum
28 Little Red Riding Hood
29. The Little Engine That Could
30. The Fox and the Crow
31. Snow White
32. Anansi and the Turtle
33. Riki Tiki Tavi
34. Jacob and the Wise Man
35. Goldilocks and the Three Bears
36. The Boy Who Cried Wolf
37. The Frog Prince
Music and Poems
1. Old MacDonald Had a Farm
2. A Wise Old Owl
3. The ABC Song
4. The Owl and the Pussy Cat
5. Counting 1 to 10
6. I’m a Little Teapot
7. All the Colors of The Rainbow
8. Itsy Bitsy Spider
9. Rock-a-Bye Baby
10. If You Are Happy and You Know It
11. Round and Round the Garden
12. Twinkle, Twinkle Little Star
13. The Noble Duke of York
14. The Wheels on the Bus
15. Pease Porridge Hot
16. Every Letter Makes a Sound
17. Down by the Bay

10
18. Jack Be Nimble
19. Bingo
20. Star Light, Star Bright
21. The Muffin Man
22. Pat-a-Cake Baker’s Man
23. Five Little Speckled Frogs
24. My First Counting Song
25. Hey Diddle, Diddle
Sleepy Time Lullabies
1. Hush Little Baby
2. Beethoven’s “Ode to Joy”
3. Brahms’ “Lullaby”
4. Ocean Waves - Music of the Sea
5. Pachelbel’s “Canon in D”
6. Bach’s “Minuet in G”
7. Earth’s Song
8. Vivaldi’s “Spring”
9. Frère Jacques
10. Beethoven’s “Für Elise”
Recorded Story
The toy is capable of recording one story. Maximum recording
time is 10 minutes.
Timer
Choose up to three stories, 25 songs or 10 lullabies to be played
before the unit automatically turns off.

11
Playlist
Choose your top five stories, songs, poems or lullabies to listen
to in your playlist.
To Add an Item to Your Playlist
1. Use the On/Off/Mode Selector Dial to choose a category.
2. Use the Next/Back Buttons to navigate to a story or song.
3. Press and hold the Star Button for three seconds to add
the item to your playlist.
4. Audio will confirm when the item has been added.
To Delete an Item From Your Playlist
1. Use the On/Off/Mode Selector Dial to choose a category.
2. Use the Next/Back Buttons to navigate to a story or song
in your playlist.
3. Press and hold the Star Button for three seconds to delete
the item from your playlist.
4. Audio will confirm when the item has been deleted.
To Listen to Your Playlist
1. Quickly press the Star Button to enter your playlist.
2. Your playlist will automatically begin playing. Use the arrow
buttons to navigate to a particular story in your playlist.
Note: To preserve battery life, you may want to limit the amount
of stories in your playlist to three or less.

12
Downloadable Content
Download additional free stories, songs and poems using your
computer and add them to your On-the-Go Story Pal™ device.
1. Power Up and Connect
Locate the On/O/Mode Selector Dial on the back of your
On-the-Go Story Pal™ device and rotate it to the Stories
category. Then, connect the device to your computer using
a micro USB cable (micro USB cable not included).
2. Set Up
Install the LeapFrog®Connect application for the On-the-Go
Story Pal™ onto your PC or Mac computer
from leapfrog.com/connect
3. Download
Follow the on-screen instructions to download and install
additional content.
4. Play and Learn!
Eject the On-the-Go Story Pal™ device and your child is ready
to play!
Warning: Do not power off the device or disconnect the
micro USB cable while the device is being updated.
System Requirements for Computer Connection
High-speed Internet connection; parent account registration;
monitor resolution of 1024 x 768; available USB port; 1 GB of
RAM; 500 MB free disk space.
PC Requirements: Pentium®4 or equivalent (2 GHz processor
or faster recommended); 64-bit version of Windows®8 or
Windows®10 operating system with latest service pack.
Mac Computer Requirements: Apple computer (1 GHz processor or
faster recommended); Mac OS X 10.13+ operating system software.
WINDOWS is a trademark of Microsoft Corp., registered in the
U.S. and other countries. PENTIUM and INTEL are trademarks of
Intel Corp., registered in the U.S. and other countries. Macintosh
and Mac logos are trademarks of Apple Inc. in the United States
and other countries. All other trademarks are the property of
their respective owners.

13
CARE & MAINTENANCE
1. Keep the unit clean by wiping it with a slightly damp cloth.
2. Keep the unit out of direct sunlight and away from any direct
heat sources.
3. Remove the batteries if the unit will not be in use for an
extended period of time.
4. Do not drop the unit on hard surfaces and do not expose
the unit to moisture or water.
IMPORTANT SAFETY INSTRUCTIONS
Adult supervision required at all times while children are playing
with this product.
Not suitable for children under 18 months.
Routinely check this toy for proper and safe condition. If there
is any damage or broken parts, remove toy from use.
Long-term exposure to loud sounds, at high volume, may result
in permanent hearing loss. When using headphones or ear
buds, it is recommended that the product is listened to at lower
volumes for shorter periods of time. Set the volume while in a
quiet environment; turn the volume down if you cannot hear
people speaking near you. The louder the volume, the less time
required before your hearing may be affected. If you experience
ringing in your ears or hear muffled speech, stop listening and
have your hearing checked.
Headphones should not be used by children under the age of
36 months.

14
TROUBLESHOOTING
If for some reason the unit stops working or malfunctions,
please follow these steps:
1. Turn the unit Off.
2. Interrupt the power supply by removing the batteries.
3. Let the unit stand for a few minutes, then replace the batteries.
4. Turn the unit On. The unit should now be ready to use again.
5. If the unit still does not work, install a new set of batteries.
Problem Possible Cause Correction
The On-the-Go
Story Pal™
device has
stopped working
or does not turn on
Incorrect battery
polarities
Ensure that the batteries are
installed correctly
Weak batteries Replace with new batteries
Cannot download
additional stories
The LeapFrog®
Connect
application is not
installed
Install the LeapFrog®Connect
application on your PC or Mac at
leapfrog.com/connect
The LeapFrog®
Connect
application is not
working
Disconnect the On-the-Go Story
Pal™ device and restart the
LeapFrog®Connect application.
Then, reconnect the On-the-
Go Story Pal™ device to your
computer again using a micro USB
cable.
Cannot find any
story in the device
The data in the
On-the-Go Story
Pal™ device has
crashed
Connect the On-the-Go Story
Pal™ device to your computer, run
the LeapFrog®Connect application,
select Reset under Settings and
your On-the-Go Story Pal™ device
will be restored. Your recorded story
will be erased.

15
Environmental Phenomena
The unit may malfunction if subjected to radio-frequency
interference. It should revert to normal operation when the
interference stops. If not, it may become necessary to turn the
power OFF and back ON, or remove and reinstall the batteries.
In the unlikely event of an electrostatic discharge, the unit may
malfunction and lose memory, requiring the user to reset the
device by removing and reinstalling the batteries.
Impact de l’environnement
Une défaillance de fonctionnement de l’appareil peut
survenir s’il est sujet à des interférences avec les fréquences
radioélectriques. Le fonctionnement normal de l’appareil devrait
reprendre avec l’arrêt des interférences. Si ce n’est pas le cas, il
peut s’avérer nécessaire d’éteindre et rallumer l’appareil ou de
retirer et réinstaller les piles. Dans l’éventualité peu probable
d’une décharge électrostatique, un mauvais fonctionnement
et une perte de mémoire de l’appareil peuvent se produire.
L’utilisateur doit alors retirer et réinstaller les piles pour
réinitialiser l’appareil.
IMPORTANT NOTE:
If the problem persists, please call our Consumer Services
Department at 1-800-701-5327 in the U.S. or email
[e-mail]. Creating and developing LeapFrog®
products is accompanied by a responsibility that we take
very seriously. We make every effort to ensure the accuracy
of the information, which forms the value of our products.
However, errors sometimes can occur. It is important for you
to know that we stand behind our products and encourage
you to contact us with any problems and/or suggestions
you might have. A service representative will be happy to
help you.

16
DISCLAIMER AND LIMITATION OF LIABILITY
LeapFrog Enterprises, Inc. and its suppliers assume no
responsibility for any damage or loss resulting from the use of
this guide. LeapFrog Enterprises, Inc. and its suppliers assume
no responsibility for any loss or claims by third parties that may
arise through the use of this product. LeapFrog Enterprises,
Inc. and its suppliers assume no responsibility for any damage
or loss caused by deletion of data as a result of malfunction,
dead battery, or repairs.
NOTE
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved
by the party responsible for compliance could void the user’s
authority to operate the equipment.

17
Supplier’s Declaration of Conformity
47 CFR § 2.1077 Compliance Information
Trade Name: LeapFrog®
Model: 6137
Product Name: On-the-Go Story Pal™
Responsible Party: LeapFrog Enterprises, Inc.
Address: 2200 Powell Street, Suite 500,
Emeryville, CA 94608
Website: leapfrog.com
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY
INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT
MAY CAUSE UNDESIRED OPERATION.

LeapFrog Enterprises, Inc.,
A subsidiary of VTech Holdings Limited.
TM & © 2021 LeapFrog Enterprises, Inc.
All rights reserved.
91-003934-006 US
Visit our website for more
information about our products,
downloads, resources and more.
leapfrog.com
leapfrog.ca
Read our complete warranty and
policies online at:
leapfrog.com/legal