Lefroy Brooks M2-5341 User manual

Size: 215.9*279.4mm K 100%
INSTALLATION INSTRUCTIONS
M2-5341
FLEETWOOD ROBE HOOK

2

3
Dimensions in Inches (& Millimetres)
Whilst every effort is made to ensure accuracy, design and dimensions are subject to
change without notice as part of the company’s product development process.
Ø1 15/16"
Ø1 1/16"
Ø1/2"
Ø1 3/8"
5/8"
1 5/8"
1/8"
5/16"
(Ø50mm)
(Ø27mm)
(Ø12mm)
(Ø35mm)
(15.9mm)
(42mm)
(3mm)
(8mm)

4
What you need to know
Adjustable Wrench
Groove Joint Pliers
Hacksaw
Phillips Screwdriver
Pipe Tape
Spatula
Spirit Level
Your new bathroom faucet is designed for years
of trouble-free performance.
Keep it looking new by cleaning it periodically with
a soft cloth. Avoid abrasive cleaners, wire wool and
harsh chemicals as these will dull the finish and
void your warranty.
If you are soldering during faucet installation,
remove cartridges, seats, gaskets and washers
prior to applying flame, otherwise you will void
the warranty.
Cover drain openings to avoid losing small parts.
When cutting or soldering pipe, use safety glasses
to protect your eyes.
Correct installation may vary depending on previous faucet installation. All necessary supplies required for
faucet installation are not included, but may be found where plumbing supplies are sold. It is suggested that
IAPMO and/or CSA approved plumbing supplies are used during installation.
Prior to beginning installation. turn off the cold and
hot water lines and open the old faucet to release
built-up pressure.
Overtightening nuts may cause damage.
Wrap all threaded connections with pipe tape
available at your local plumbing supply store.
Always wrap in a clockwise direction. The fittings
should be installed by a state-licenced plumber.
Tools: Maintenance
SafetyTips
ThingsYouMayNeed
ImportantPoints
Meets A112.18.1
Standards

5
Steps 1-3
InstallationProcedure
Lefroy Brooks always recommends that plumbing products be installed by a licensed professional.
Shut off main water supply before installation.
3Place assembly over the mounting bracket
with set screws facing down. Tighten the
set screws.
1Position the mounting bracket on the wall
where required. Please note the direction of
the bracket should be as shown. Mark the
location of mounting screws. Drill holes in
the wall to fit the anchors. Tap the plastic
anchor into the hole with a hammer.
2Position the mounting bracket to be
mounted on the wall, then thread the fixing
screws through the mounting hole into the
plastic anchor. Turn the screws slowly until
they are tight.
3
21

6
E ploded View
PartsList
Decorative head (243056)
Bracket (245027)
Screw (008715)
Mounting bracket (293014-3)
Anchor bolt and screw (290411)
Set screw (292547)
Allen key (031003)
1
2
3
4
5
6
7
1
2
3
4
5
6
7

7

The use of trademarks, product design and artwork is subject to licence or agreement with Christo A. Lefroy Brooks. The design
registrations, trademark registrations and copyrights are protected by law and the use or reproduction outside the terms of an agreement is prohibited.
The right to modify designs and dimensions is reserved. Christo Lefroy Brooks is a member of ACID (Anti Copying in Design).
LEFROY BROOKS INC, 1828 TROUTMAN STREET, RIDGEWOOD, NY, 11385
TELEPHONE: [phone]. FAX: [phone]
©CHRISTO A. LEFROY BROOKS 2009
For additional assistance or service call
718-302-5292
9am to 5pm EST Monday to Friday
www.lefroybrooks.com