LEGRAND 036 12 User manual

9
Modular scenario switch
036 12
100 - 240 V±
50 - 60 Hz
Voltage
Frequency
Dimensions
2 x 1,5 mm2
1 x 2,5 mm2
EN 50065
IEC 60669-2-1
-5°C à + 45°C
4 modules
Characteristics Description
LEARN indicator
LEARN key
Preset mode
indicators
Control key
1, 2, 3, 4, 5, 6, 7, 8
Auxiliary inputs
Auxiliary inputs

10
Badge reader
- Closing
Badge reader
- Opening
Switch
Pushbutton
036 12
100-240 V
50-60 Hz
NL
1
1
3
234
5678
LEARN
57
2468
L L
L L
N
L
Safety instructions :
This product shouldbe installedpreferablybya qua-
lifiedelectrician. Incorrect installation anduse can entail risk of
electric shock or fire.
Before carrying out the installation, readthe instructions and
take account of the product's specific mounting location.
Do not open up the device. All Legrandproducts must be
exclusivelyopenedandrepairedbypersonnel trainedand
approvedbyLEGRAND. Anyunauthorisedopening or repair
completelycancels all liabilities andthe rights to replacement
andguarantees.
Onlyuse genuine accessories.

11
Operation
As a transmitter :
This product can simultaneouslycontrol groups of receivers linkedto it during learning(1) using buttons 1, 2, 3, 4, 5, 6, 7 or 8.
Products that can be connectedto auxiliaryinputs include :
- Push-buttons
- Switches
- Clocks
- Badge readers
- Etc. (products with drycontact outputs)
(1) Learning : procedure that enables a scenario to be definedandsaved.
(2) Scenario : set of controls executedsimultaneouslyon the various receivers (actors) that have been linkedto the transmitter (leader) during
the learning procedure.

12
1 Preset(*) Scenario 1 / End of Preset No action
2 Scenario 2 No action
4 Scenario 4 No action
5 Scenario 5 Increasing light level
6 Scenario 6
Decreasing light level
7 Scenario 7 No action
8 Scenario 8 No action
3 Preset(*) Scenario 1 / End of Preset No action
1 End preset Scenario 1 Preset Scenario1
2 Scenario 2 no action
4 no action Scenario 4
8 no action Scenario 8
5 Scenario 5 (Dimming + if held) no action
6 Scenario 5 (Dimming if held)
no action
7 Scenario 7 no action
3 Preset Scenario 3 End of preset Scenario 3
Key Short press Longpress
Badge reader
(Closing)
Badge reader
(Opening)
Double pushbutton
Single switch
Auxiliary
Input
Example of
Product Phase present Phase absent
On return of power :
After a break in power supply, the
multi-function pushbutton runs a
status check on all the auxiliary
inputs andregisters anystatus
changes that occurredduring this
break.
(*) Preset => to lock a scenario into the status programmed
Operating auxiliary inputs
Operating local keys

13



Learning a scenario
Key
The indicator light
switches off
Press LEARN Press one of the three control buttons
Press LEARN Press one of the three control buttons
The indicator lights of all products switch off.
The scenario has been saved.
Step 1 : start the learning phase (on the TRANSMITTER)
Step 2 : add an actor to the scenario (on the RECEIVER)
Step 3 : save the scenario (on the TRANSMITTER)
To add several products to the scenario, repeat operations andfor each receiver.
The indicator light
flashes slowly
The indicator light
flashes quickly
The indicator
light flashes

14




Modifying a scenario
Press LEARN Press the control button that controls
the scenario
Press the desired
The indicator lights on all products blinks quickly
Press LEARN
Press
LEARN
Press LEARN
or
To delete the product
from the scenario go to step 3
The indicator lights on all products switch off.
The scenario has been saved.
Step 1 : open the scenario (on the TRANSMITTER)
Step 2 : modifythe status of a scenario receiver (on the RECEIVER)
Step 3 : save the scenario (on the TRANSMITTER)

15


Deleting a scenario (on the TRANSMITTER)
Press LEARN
The scenario is deleted
Press the control buttonandhold
for 10 secs
Press LEARN Press LEARN
andholdfor 10 secs
Product goes back
to factorysettings
Step 1 : delete all the scenarios linkedto the control button
Step : delete all the scenari

Problems and solutions
ProblemCause Solution
The learn indicator light comes on Learning is impossible. Install compatible products.
for 5 seconds.
The learn indicator light comes on The number of saved Delete the unused scenarios.
for 10 seconds. transmitters is more than 32.
During learning the learn indicator The learning mode shuts down Restart the learning.
light stops blinking. after 10 minutes
(if no action).
The programmed function button After pressing the learn button, Restart the learning.
does not work. the learning of the function button
is done in the minute that follows.
On saving the scenario, Incorrect communication Check the cabling (connection).
the learn indicator lights between the products. Look for a possible interference device.
of some receivers do not go off. Insulate with a filter.