LEGRAND HPM Vivo EVM970L Series User manual

EV970L / EVM970L EVM970LIM EVM970LBP
Nominal Input Voltage 250 V a.c.
Rating (Fluorescent/Incandescent) 10 AX 10 AX 10 A
Rating (LED) 100 W -
Switch type 2-way Intermediate Momentary
Terminals 2 x 1.5 mm2 or 1 x 2.5 mm2
■1 x Push-button mechanism
■1 x Pack of buttons (Red or Blue lens) and rings
■Instruction Sheet
■1 x EVM970L push-button mechanism (see opposite for content)
■1 x Grid and Plate
■Instruction Sheet
EVM970L / EVM970LBP
EVM970LIM EV970L
■This product must be installed and used as per these instructions.
■This product must be installed by a licensed electrician or similarly qualified person.
■V90-rated building wire must be used when wiring this product.
■This product has been designed with limited short circuit protection.
■ Repeated short circuits may still damage the product.
■Severe electromagnetic interference from other products may cause malfunction of this product.
■ This product should only be cleaned with a damp cloth. Cleaning agents and solvents should not be used.
■ This product contains no serviceable parts and no attempt should be made to repair this product. If the product
is faulty it should be discarded.
■ Legrand reserves the right to modify the specifications of this product at anytime.
Push-button mechanism
Ring
Grid
Plate
Button
Package Contents
Technical specifications
Important Information
EVM970L
VivoTM
MECHANICAL PUSH-BUTTON
Instruction Sheet
EVM970L / EVM970LIM / EVM970LBP/ EV970L Series
EVM970L series EV970L series

(Note: Laser marking is done on front of mechanism for guidance)
1. Pick the button with the desired coloured LED lens: Red or Blue
2. Check the wall plate orientation: Vertical or Horizontal. See fig. D.
3. Clip the button and press firmly on the mechanism. See fig. A and B.
4. Clip the ring.See fig. C.
5. Clip the assembly into the grid and proceed to wiring (Refer to wiring section below).
Horizontal Plate
Vertical Plate
CLICK
CLICK
A
A
B
D
D
C
C
B
Installation (EVM970L series)

EVM970L
EVM970L
EVM970L
EVM970L
Wiring
One way switching
LED Indicator ON when Load is ON
Active and Neutral at Switch
LED Indicator always ON
Active and Neutral at Switch
LED Indicator ON when Load OFF
(High impedance Load)
Active and Neutral at Switch
LED Indicator ON when Load OFF
(High impedance Load)
Active at Switch, Neutral at Load
LOAD A
N
LOAD A
N
LOAD A
N
LOAD
N
ELE6VA
*
A
LED
LED
LED
LED

EVM970L EVM970L
LED
Two way switching
Three or more way switching
LED Indicator ON when Load OFF
Active and Load at first Switch
LED Indicator ON when Load OFF
Active at first switch and Load at last switch *May be required for High Impedance Loads
A
LOAD
N
ELE6VA
*
LOAD N
ELE6VA
*
A
EVM970L EVM970L
EVM970LIM
LED LED
LED
LED
Warranty
Legrand will honour all statutory guarantees that you as a consumer are
entitled to rely upon under the Australian and New Zealand Consumer
Laws against a manufacturer, including a guarantee that this product is
of acceptable quality.
To make a claim under any statutory guarantee you should first contact
the supplier, or retailer from whom you purchased this product.
Customer Service
For all Customer Service and Technical Support
please call Monday to Friday during business hours.
LE12736AA 02/2021
Legrand Australia
1300 369 777
www.hpm.com.au
Legrand New Zealand
0800 476 009
www.hpm.co.nz
ABN: 31 000 102 661
Paper