LEGRAND HKRL10 User manual

installation guide
Smart Switch
Room . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HKRL10
with HomeKit Technology

2
table of contents
before you start..................................3
what you need ...................................4
getting to know your switch ..........6-7
installation and setup ................ 8–23
specifications.............................24-25
faqs ....................................... 25–29
regulatory information ......... 30–33
warranty.......................................34
support ........................................35

3
before you start
Review this guide in its entirety before beginning device installation. Consult an
electrician with any questions or if you are unsure of your abilities.
DWarning: Incorrect installation could
result in death, serious injury, and/or
damage to your home or devices.
DCaution: To reduce the risk of injury
and/or overheating and damage to other
equipment:
• For dry, indoor use only.
• Do not use to power medical equipment.
• Not suitable as a disconnecting means.
• Do not use with loads exceeding the
device load rating (see page 24).
• Connect the smart switch to a
120 VAC, 60 Hz power source ONLY.
• Always use copper wire to install the
smart switch and follow all applicable
local and national electrical codes.
• Install in a non-metallic electrical box
to protect wireless signal strength.
Visit the Legrand website at www.legrand.us/radiant/homekit.aspx to learn more about
your smart device.

4
what you need
REQUIRED:
Phillips-head screwdriver
Flat blade screwdriver
YOU MAY ALSO NEED:
Non-contact voltage tester, pliers, wire cutter, wire stripper, electrical tape,
flashlight, radiant®screwless wallplate (included), wiring leads (included), and
wire nuts (included)
NOTE: Exercise caution when using power tools. Overtightening the screws can
damage the device.

5

6
getting to know your switch
Item Name Description
1 Paddle Switch
• Press the top of the paddle to turn the light on
and the bottom to turn the light off.
• To return the switch to factory default, press and
hold the top of the paddle for 15 seconds. Then,
remove the device from the Legrand Home app
(or Apple Home app).
2 LED Locator Light Indicates the current state of the device. Refer to
“LED Locator Light Explanations” for detail.
NOTE: For in-wall control of this switch in a three-way application, refer to the installation
instructions for the HomeKit Remote Switch (HKRL20).

7
1
2
LED LOCATOR LIGHT EXPLANATIONS
LED
Color State of Light Explanation
Slowly Flashing
Amber
Device is attempting to connect to
the network
Solid White Connected to Wi-Fi and turned off
No Light Device is on
Rapidly Flashing
Amber
N-Way Pairing mode: device is
ready to pair with the remote(s)

8
installation & setup
step one
|
turn off the power for your device at the
circuit breaker
Flip the existing light switch multiple times to confirm the power is off.
NOTES:
• If there are multiple devices next to your existing light switch, make sure power is
off at the circuit breaker for all of those devices.
• For multi-way installations using a remote switch, follow the instructions for the
remote device (HKRL20).

9
OFF
ON
OFF
ON
OFF
ON
OFF
ON
OFF
ON

10
installation & setup
step two
|
remove the existing device
Check for the following wires:
1HOT or LINE: Receives power from the circuit box. Referred to as “hot” for the
purposes of this guide. Do not touch or let “hot” wires contact other wires.
2LOAD: Directs power to your light(s).
3NEUTRAL: Creates a path to return current to the power source when the
device is off. Required for your switch installation.
4GROUND: Provides a safe path for electricity in the event of a short circuit.
NOTE: Refer to the “faqs” on page25 if you are unsure of your wiring.