LEGRAND Celiane 670 85 User manual

670 85
Setting of minimum
and maximum thres-
holds for compact
fluorescent loads
Product configuration
micro-switch:
- Default setting
- Description page 5
Description
CélianeTM
Universal dimmer switch
www.lum-art.ru
LumArt

22
Characteristics

35°C
0°C
100 V AC
240 V AC
50/60 Hz
2 x 2.5 mm2
(*)
Dimmable Not
dimmable
240 V AC
Max. 300 W 300 W 300 VA 300 VA 160 VA 160 VA 160 VA 160 VA 160 VA
Min. 40 W 40 W 40 VA 40 VA 16 VA 16 VA 8 VA 8 VA 8 VA
110 V AC
Max. 150 W 150 W 150 VA 150VA 80 VA 80 VA 80 VA 80 VA 80 VA
Min. 40 W 40 W 40 VA 40 VA 16 VA 16 VA 8 VA 8 VA 8 VA
(*) Use only with transformers designed to function with electronic switches.
www.lum-art.ru
LumArt

23
Wiring
N
www.lum-art.ru
LumArt

24
Installation




* not supplied with the mechanism
www.lum-art.ru
LumArt

25
Configuration
Reserved for “After-sales Service”
Product configuration (see detail § “End stop setting method” for type
lamps.
Level memory activated deactivated
Selection of the type of load
www.lum-art.ru
LumArt

26
Configuration (cont.)
Capacitive mode 
Not dimmable
(**) According to the lamp manufacturer.
(**)
www.lum-art.ru
LumArt

27
Configuration (cont.)
Lamps of different types must not be mixed in the same product.
When changing lamp type, start by placing the product
in factory configuration by positioning the micro-switches
as follows:
Inductive mode 
(*) Use only with transformers
designed to function with elec-
tronic switches.
(**) According to the lamp ma-
nufacturer.
(*)
Dimmable
(**)
www.lum-art.ru
LumArt

28
Configuration (cont.)
Fluorescent and compact fluorescent lamps:
Minimum and maximum lighting settings, recommended when the lamp flickers. (Before setting, let the lighting
stabilise by leaving the lamp lit for a few seconds).
The right-hand buttons (+/-) can now be used to vary the level in the dimming range set using two potentio-
meters.
Repeat steps 1 to 4 described above to modify the settings.
/01 2
Set the minimum level
of lighting sought
Set the maximum level
of lighting sought
www.lum-art.ru
LumArt

Configuration (cont.)
When first switching on, if the load starts blinking then remains out:
1 - Check that the green and orange LEDs blink in succession.
2 - Reverse the position of switch 1.
3 - The LEDs stop blinking.
4 - The equipment is therefore working correctly.
4
3
2
1
NO
4
3
2
1
4
3
2
1
4
3
2
1
4
3
2
1
NO
NO
NO
4
3
2
1
OR
www.lum-art.ru
LumArt

30
Safety instructions
This product should be installed in line with installation rules, preferably by a qualified electrician. Incorrect installation and
use can lead to risk of electric shock or fire.
Before carrying out the installation, read the instructions and take account of the product’s specific mounting location.
Do not open up, dismantle, alter or modify the device except where specifically required to do so by the instructions. All Le-
grand products must be opened and repaired exclusively by personnel trained and approved by Legrand. Any unauthorised
opening or repair completely cancels all liabilities and the rights to replacement and guarantees.
Use only Legrand brand accessories.
www.lum-art.ru
LumArt