Leica Sprinter 250M User manual

LEICA SPRINTER Quick Guide English
Instrument Components
a) Horizontal fine motion screw
b) Battery compartment
c) Circular level
d) Gunsight
e) Focusing knob
f) Handle
g) Eyepiece
h) LCD display
i) Base plate
j) Levelling footscrew
Operating Keys and Functions
*) when in Menu mode
a
j
i
h
g
f
e
d
b
c
Sprinter_01
Key Symbol 1st level funct. 2nd level funct.
On/Off Power On/Off
switch
NONE
MEAS Measuring
trigger key for
measuring
height and
distance
2nd function
(Continuous meas-
urement) with
prolong key press of
2 seconds
Height
/ Dist.
Alternating bet-
ween Height and
Distance display
Cursor up *
dH Height Differ-
ence measure-
ment and RL
computation
Cursor down *
MENU Activation and
selection of
settings
ENTER key for
confirmation
purpose *
Back-
light
LCD backlight
illumination
ESC key for termi-
nation of program or
setting *

2
Measurement Modes and Icons
Modes
Icons
Measurement
Height and Distance measurement
Symbol Mode
Measurement Mode
MENU selection Mode
Adjustment Mode
Tracking Mode
Icon Description
LCD backlight on
Staff upright measuring mode
Inverted Staff measuring mode
Different levels of LCD contrast display
(10% change per step)
Battery icon at various capacity (0%, 25%,
50%, 75%, 100%)
External power utilized *
Data stored to internal memory
MEAS
MENU
ADJ
TRK
Step Key Description
1. Press to switch on the instrument,
Leica logo is displayed follow by the
default measurement standby mode.
2. Aim at staff and focus. Lightly trigger
the measurement key to activate
measurement.
3. Height and distance measurement
are displayed.
: 1.235m
: 5.68 m

3
Reduced level, Height difference, Height and Distance measurement
In MENU setting (for SPRINTER 100M/200M):
• In submenu Recording > select Memory or Ext. if captured data to be stored.
• In submenu Input PtID > edit/input PtID as desired. Point ID only display when memory is ON.
Step Key Description
1. Press to start height difference and reduced level function.
2. Press, choose Input RL to change/input desired reference/benchmark level.
3. Press to complete input.
4. Aim at reference staff press key to initiate measurement.
5. Reference height & distance displayed follow by message Meas. Target!
6. Aim at target point press key again to display the result.
Display with active
internal memory
RL:
dH:
99.138
m
- 0.900 m
2.135 m
31.11 m
:
:
2
PtlD :
2.135 m
31.11 m
:
:
99.138
m
- 0.900 m
RL:
dH:

4
MENU Setting
*) Applicable to SPRINTER 100M/200M only
740359-1.1.0en • Leica Geosystems AG • CH-9435 Heerbrugg (Switzerland) • Phone [phone] • Fax [phone] • www.leica-geosystems.com
No. Sub Menus Selections Descriptions
1. Input PtID * To input user point ID
2. Input Reduced
Level (RL)
Input for Benchmark value / Reference Reduced Level
3. Data
Manager *
View, Delete, Down-
load
Viewing of individual recorded data and deleting of specific measuring data,
Deleting of all data, Transferring of data via PC software.
4. Recording * Memory, External,
OFF
Data can be recorded in the internal memory of the instrument or externally to
the external device such as data collectors. If the recording is set OFF, then the
captured data will not be stored.
5. Adjustment None Adjustment program
6. Inverse Staff ON=Inverted mode
OFF=Upright mode
Setting of measurement to Inverted Staff. By default or on power on, the mode
is always set to OFF.
7. Contrast 10 levels of select. Optimum contrast setting for LCD display. Contrast is set to 50% ex factory.
8. Unit M, INT ft, US ft, Ft in
1/8in
Display Unit setting in meters, international feet, US feet, and ft in 1/8in
9. AutoOFF ON 15 min / OFF Power saving function. If set to ON 15 min, the instrument will switch off about
15 minutes after the last key press. In the case of OFF, the instrument will be
permanently switched on
10. Rounding Standard/Precise Standard = 0.001m / 0.01ft for height and 0.01m / 0.1ft for distance.
Precise = 0.0001m / 0.001 ft for height and 0.001m / 0.01 ft for distance.
In Ft in 1/8 inch; Precise/standard = ft-inch-1/8 inch for height & distance.
11. Beep ON/OFF Acoustic signal trigger key ON or OFF
12. RS232 * Baudrate
Parity
Stop Bit
Data Bit
1200, 2400, 4800, 9600, 19200, 38400
None, Odd, Even
1, 2
7, 8