Leisure Concepts Smartop SwimSpa Upright 3.0 User manual

Installation Instructions - Updated as of 07/09/20
Page 1
Smartop SwimSpa Upright 3.0 200709
SwimSpa Upright 3.0
Figure 2
Step #1
Position the Smartop (in the closed position) on the spa making sure that all
four corners are properly positioned and square on the spa with the two cover
halves meeting in the middle with no gap between the covers.
Step #5
While pressing downward on the Smartop cover mounting bracket, swing the
Smartop cabinet mounting bracket up until it is parallel with the spa acrylic
and attach to the spa cabinet using the supplied #10 x 2” mounting screws
(see Fig. 3).
Step #4
Attach the Smartop 3.0 cabinet mounting bracket to the Smartop 3.0 cover
mounting bracket, in the bottom hole, using the supplied 3/8 x 2” button
head socket bolt, washer and locknut (see Fig. 3). Note: You are supplied with
(7) plastic spacers per bracket, so make sure to use equal amounts on either sides
of the Smartop cabinet mounting bracket where the bolt goes through.
Figure 1 EAS Bracket
EAS Handle
Button Head
Socket Bolt
Step #2
Attach the EAS handle to the EAS bracket using the supplied 5/16 x 1-1/4”
button head socket bolt (see Fig. 1).
J
K
Washer
Locknut
Figure 3
Button Head
Socket Bolt
F
G
E
Step #3
Insert the 3/8 x 2” button head socket bolt into the top hole in the back of
the Smartop cover mounting bracket. Make sure to install the rubber stop
on the button head socket bolt once you insert the bolt through the outside
flange of the Smartop cover mounting bracket. Secure the 3/8 washer and
locknut to the opposite end of the button head socket bolt (see Fig. 2). Note:
Do not overtighten locknut.
Washer
Locknut
Plastic
Spacers
Mounting
Screws
Button Head
Socket Bolt
F
G
E
L
H
Rubber
Stop
I
Cover
Mounting
Bracket
Step #6
Repeat steps 2 through 5 for the 2nd cover before proceeding to step #7.
Step #7
Gently raise the Smartop into the upright position making sure to keep a firm
grip on the cover and attach the shocks to the ball studs (see Fig. 4). Note:
When attaching the shocks, make sure the black body of the shock is on top. The
ball studs are pre-installed in the hole closest to the back of the bracket. If the
Smartop doesn’t lift off the spa easily, start by moving the ball stud on one of the
sides of the spa to the front hole and re-attach the shock. If the Smartop still
doesn’t lift off the spa easily, move the ball stud on the opposite side of the spa and
re-attach the shock.
Figure 4
Shock
(Black Body)
N
Cabinet
Mounting
Bracket
A

Page 2
Latch Catch
Smartop SwimSpa Upright 3.0 200709
Step #8
Connect the Sure Lock latch assembly to the latch catch. While
pushing down on the Smartop, position the Sure Lock latch on
the side of the spa and mark where the latch base rests against the
spa skirting. Attach the Sure Lock latch to the spa skirting, where
marked, using the supplied #8 x 3/4” self-tapping screws (see
Fig. 5).
Figure 5
Sure Lock
Latch Assembly
(Side of Spa)
O
Press down to
compress thermal
seal when installing
the Sure Lock
Self-Tapping
Screws
P
Operation of your Smartop Cover
1) Fold the first half of the Smartop cover off the spa. While gripping the
EAS handle, motion the Smartop cover into it’s vertical upright position.
CAUTION! Do not use the Smartop in high wind conditions. Injury from the spa cover being blown over
and impacting the spa user can occur.
For additional information on our Smartop product, please visit our website: “www.smartopspacover.com”
ITEM PART# DESCRIPTION QTY
A(L) 101875 ST UPRIGHT 3.0 CABINET MOUNTING BRACKET (L) 2
A(R) 101876 ST UPRIGHT 3.0 CABINET MOUNTING BRACKET (R) 2
B 100244 5/16 BALL STUD 8
C 100032 5/16 NYLON LOCKNUT 8
D 100034 BLACK HEX DOME CAP 4
E 101749 3/8 X 2" BUTTON HEAD SOCKET BOLT - BLACK ZINC 8
F 100951 3/8 FLAT WASHER - BLACK ZINC 8
G 100838 3/8 LOCKNUT 8
H 101877 3/8 X 1/8" PLASTIC SPACER 28
I 101885 RUBBER STOP 4
J 101596 EAS HANDLE 4
K 101751 5/16 X 1-1/4" BUTTON HEAD SOCKET BOLT - BLACK ZINC 4
L 100359 #10 X 2" PHILIPS PAN HEAD MOUNTING SCREW 40
M 100016 SMALL BLACK DOME CAPS 48
N
101796
101880-101884
SHOCK 4
O 101871 SURE LOCK LATCH ASSEMBLY 2
P 101065 #8 X 3/4" PHILIPS FLAT HEAD SELF-TAPPING SCREW (BLACK ZINC) 8
Q 101078 LOCK 1