Lekker Jordaan Step Through Quick guide

Assembly &
Maintenance
Guide
Jordaan
Step Through

32 Jordaan Step ThroughAssembly & Maintenance Guide

5Jordaan Step ThroughAssembly & Maintenance Guide
Enjoy your
Jordaan Step Through
Dear LEKKER Customer, First and foremost – congratulations
on your brand new bicycle! We can’t wait for you to experience the
thrill and joy of riding your LEKKER bike, the Amsterdam way. But
before you do, we want to help you make sure your bike is in tip-top
condition, as well as provide you with some tips and tricks to keep it
that way.
This manual will outline all the tools and knowledge needed
to put the nishing touches on your bike, as well as how to use it
and useful guidance on maintenance and care. Feast your eyes on
what’s to come – we guarantee it’ll be worthwhile, even if you’re an
experienced rider.
The rst few chapters are particularly important, for both
your enjoyment and safety, as we walk you through key steps in
ensuring your bike is safe to ride.
Please also note that as your brand new Jordaan Step
Through is hot o the press, the images in this manual might not be
reective of the bike that's in front of you. The images used are from
one of our older bike models. And without them, we thought your
manual wouldn't look quite so beautiful.
Note: We have to stress that this manual won’t teach you all the skills of a bicycle mechanic.
Even a manual the size of every Harry Potter book combined couldn’t detail every possible
combination, tricks and available components. For this reason, our manual is only applicable
to your new LEKKER bicycle and its assembly, alongside any important notes, warnings and
maintenance guides.
Contact
Australia & USA
Sydney
[phone][email protected]
134 Botany Rd Alexandria NSW
2015, Australia
Melbourne
[phone][email protected]
23 Provost Street Nth.
Melbour-ne VIC 3051, Australia
Brisbane
[phone]
[email protected]
2C 97 Sandgate Road Albion
4010 QLD, Australia
Warning
For safety purposes it is re-
commended that you have this
bicycle assembled by a skilled
bicycle mechanic.
Europe
Amsterdam
Tweede Kostverlorenkade 68
Amsterdam, The Netherlands
Berlin
Kollwitzstraße 47
10405 Berlin, Germany
*Check our website for contact info.

6Assembly & Maintenance Guide 7 Jordaan Step Through
Index
01.
Getting started
02.
Fitting the handlebars03.
Fitting the pedals 04.
Fitting the saddle
05.
Aligning the brakes06.
Aligning the gears07.
Finishing touches
08.
Safety and warranty
p08
p12
p16p18p22p20p24p26

98 Jordaan Step ThroughAssembly & Maintenance Guide
01. Getting
Started
We’ve created this manual to help you put the -
nishing touches on your LEKKER bike. Run through
these quick steps and you’ll be exploring and adven-
turing in no time.
So, without further ado, unbox your LEKKER bike and
feast your eyes on your newest sidekick. Once you’-
ve removed the packaging, make sure you have your
trustly toolkit to hand, as shown in the illustration on
the next page.

1110 Jordaan Step ThroughAssembly & Maintenance Guide

1312Jordaan Step ThroughAssembly & Maintenance Guide
02. Fitting the
handlebars
Handlebars.
Using a 6mm allen key, loosen the bolt located at the
top of the handlebar stem, then insert it into the
frame. Once inserted, centre the handlebar and stem
and tighten it.

21
14Jordaan Step ThroughAssembly & Maintenance Guide
To adjust the angle of the handlebar, loosen the allen
bolts of the front plate until you can move the
handle bar freely. Once you’ve found your prefer-red
bar angle, tighten the bolt.
Tip: Should you wish to adjust the angles of your
grips, brakes and shifter, you can do so with a simple
turn of allen key 3 or 4.
Steering Lock.
Your Jordaan Step Through comes tted with a stee-
ring lock to help keep your bike stationary when the
kickstand in in use.
Simply turn clockwise to engage the lock, or anti
clockwise to disengage.

1716Jordaan Step ThroughAssembly & Maintenance Guide
ATTENTION: please make sure you check the
thread direction before inserting the pedals. Fitting
the pedal to the wrong side can damage the crank
arm and is not covered under warranty.
RIGHT pedal: This pedal has no indented lines and is
smooth in between the pedal and thread
03.Fitting the
pedals
To assemble the pedals, you will need a 15mm open-
ended spanner. Insert the pedal into the crank and
ensure the pedals are properly tightened.
LEFT pedal: this is the pedal that has indented hori-
zontal lines on the small part between the pedal and
thread.

1918 Jordaan Step ThroughAssembly & Maintenance Guide
Installing the saddleStep 1: Position the rails of the saddle in the bottom clamp's channels.04.Fitting the
saddle Step 2: Tighten down the clamp bolts to lock the saddle in place. Turn the bolts clockwise with your 6 mm allen Key to screw them back into the top part of the clamp.Adjusting the saddle heightUsing the 4mm allen key, loosen the seatpost clamp bolt and insert the seatpost. Make sure it’s at the correct height. When sitting on the saddle, your knee should be at a slight bend when the pedal is at its lowest position. Then, tighten the bolt.

2120 Jordaan Step ThroughAssembly & Maintenance Guide
05. Aligning
the brakes
Lift the wheel o the ground and give it a spin. It
should spin freely and without any noise. If you hear
a metallic rubbing sound, then the brakes will need
adjusting.
To do this, you’ll need to use the 5mm allen key. With
the bike upside down, adjust the caliper. You will
need to slightly loosen the two 5mm allen key bolts
(found on the top of the caliper), so that you can
gently move the caliper horizontally, allowing the
disc rotor to move freely between the brake pads.
Tip: To help with the bedding in of your brakes and prevent squeal, we recommend 4-5 firm applications of the brakes for both front and rear during your first test ride.

2221 Jordaan Step ThroughAssembly & Maintenance Guide
06. Aligning
the gears
Step 1: Checking alignment
Begin by engaging second gear on your shiftingsystem. With second gear engaged, the yellowmark should fall in between the two white lines on the click box located on the rear wheel axle.Step 2: Adjusting alignment
On the rear click box, undo the locking nut with the 10mm spanner.Then twist the barrel adjuster until the yellow mark falls in between the two white lines.Once you are happy, tighten the lock nut again.

2423 Jordaan Step ThroughAssembly & Maintenance Guide
07. Finishing
Touches
Bell: Install the bell on your handlebars, in your pre-
ferred position. Generally, this is on the left hand
side, next to the brake lever.
Lights: Both the front and rear racks have mounting
points for lights.
Rear Light: The rear rack mounting point is located
at the very rear of the rack. Using the two 8mm bolts
supplied with the lights, mount them using the two
mounting holes and tighten.
Front Light:
Attach the front light to the light holder that’s atta-
ched to the front fork.
If you’ve purchased a front rack, the front light at-
taches to the light holder in the middle of the rack.
Using the nut and bolt provided, tighten the light
onto the xture.
Tip: Make sure you remove the plastic battery tab.
Tyres: Pump the tyres to 45-55 PSI
Accessories: If you ordered any accessories such as
racks or locks, don’t forget to t these too. They each
come with their own instructions and also have their
own mounting points.
Now, you’re good to go. Enjoy your ride, the
Amsterdam way!

27
25 Jordaan Step ThroughAssembly & Maintenance Guide
08. Safety
and warranty
We offer a 3-year warranty on our LEKKER frames.
Additionally, we supply you with 2 years warranty
on the components of our dierent models starting
on the day of purchase. This warranty is only for re-
placeable components. Unfortunately, our warranty
is not transferable (including when sold to another
consumer) and can only be used by the original buyer
of a LEKKER product. If you want to use the warran-
ty, please ensure you have your receipt and go to the
original shop in which you made your purchase.
There are cases when our warranty isn’t valid. Our
warranty doesn’t cover wear and tear, incorrect as-
sembly or maintenance. There’s no warranty in the
case of; damage caused by accidents, improper use
or negligence. Our warranty is also void if changes
are made to the original design of the LEKKER bike.
Please note: your frame number is located on the
bottom of the bike frame, near the bottom bracket.
This might be needed for insurance purposes.

Assembly & Maintenance Guide
Jordaan
Step Through
Assembly &
Maintenance Guide
lekkerbikes.com