Lekker Jordaan Quick guide

Assembly &
Maintenance
Guide
Jordaan 3-Speed
Womens

32 Jordaan 3-SpeedAssembly & Maintenance Guide

5Assembly & Maintenance Guide Jordaan 3-Speed
Enjoy your
Jordaan 3-Speed
Contact
Australia
Phone
1300 053 525 – Melbourne
0466 596 301 – Sydney
Address
23 Provost Street,
North Melbourne,
3051, VIC, Australia
415 Bourke Street, Surry Hills,
2010, NSW, Australia
Email
[e-mail]
[e-mail]
Europe & USA
Phone
[phone]
Address
Tweede Kostverlorenkade 68
Amsterdam, The Netherlands
Email
[e-mail]
[e-mail]
lekkerbikes.com
Dear LEKKER Customer, First and foremost – congratulations
on your brand new bicycle! We can’t wait for you to experience the
thrill and joy of riding your LEKKER bike, the Amsterdam way. But
before you do, we want to help you make sure your bike is in tip-top
condition, as well as provide you with some tips and tricks to keep it
that way.
This manual will outline all the tools and knowledge needed
to put the nishing touches on your bike, as well as how to use it
and useful guidance on maintenance and care. Feast your eyes on
what’s to come – we guarantee it’ll be worthwhile, even if you’re an
experienced rider.
The rst few chapters are particularly important, for both
your enjoyment and safety, as we walk you through key steps in
ensuring your bike is safe to ride.
Please also note that as your brand new Jordaan 3-Speed is
hot o the press, the images in this manual might not be reective
of the bike that's in front of you. The images used are from one of
our older bike models. And without them, we thought your manual
wouldn't look quite so beautiful.
MANUAL LEKKER BIKES / Amsterdam GT 3 MANUAL LEKKER BIKES / Amsterdam GT 4
WELCOME TO
LEKKER
Dear Lekker Customer, first of all
we would like to congratulate
you with your brand new bicycle!
It’s already a great day. But
before you ride out we want to
make sure your bike is in tip-top
condition, and you are aware how
to keep it like that. Very
important, to ensure endless
smiles each single ride.
In this manual we have compiled
for you lots of tips on how to use
your Lekker Bicycle, instructions
for maintenance and care, plus
obviously a walk through how to
execute the final assembly of
your ride. We advise to read this
manual thoroughly. You will find
it worth your while; even if you
have cycled all your life and feel
like a veteran with your new ride.
WELCOME TO
LEKKER
For your enjoyment and safety please complete the first part of this manual,
to ensure all is clear about general bicycle safety.
Chapter 2 shows you the correct thightening force in anticipation of the final
assembly of your bicycle. Chapter 3 takes you on a journey how proceed
with the final assembly of your bicycle. At last, Chapter 4 gives you a better
idea how to service and maintain your bicycle.
Your Lekker Team
Note: We have to stress that this manual
won’t teach you the skills of a bicycle
mechanic. Even a manual as big as all
Harry Potters books together could not
describe every possible combination,
tricks and available components. For this
reason this manual only focuses on your
newly Lekker Bicycle, standard assembly
and drawing your attention to important
notes, warnings and maintenance.
Note: We have to stress that this manual won’t teach you all the skills of a bicycle mechanic.
Even a manual the size of every Harry Potter book combined couldn’t detail every possible
combination, tricks and available components. For this reason, our manual is only applicable
to your new LEKKER bicycle and its assembly, alongside any important notes, warnings and
maintenance guides.
Warning
For safety purposes it is re-
commended that you have this
bicycle assembled by a skilled
bicycle mechanic.

6Assembly & Maintenance Guide 7 Jordaan 3-Speed
Index
01.
Getting started
02
Fitting the front wheel
and fender
03
Aligning the brakes
04
Fitting the saddle
and handlebars
05
Fitting the pedals
06
Finishing touches
07
Safety and warranty
p08
p12
p14
p16
p20
p22
p24

98 Jordaan 3-SpeedAssembly & Maintenance Guide
01. Getting
Started
We’ve created this manual to help you put the -
nishing touches on your LEKKER bike. Run through
these quick steps and you’ll be exploring and adven-
turing in no time.
So, without further ado, unbox your LEKKER bike and
feast your eyes on your newest sidekick. Once you’-
ve removed the packaging, make sure you have your
trustly toolkit to hand, as shown in the illustration on
the next page.

1110 Jordaan 3-SpeedAssembly & Maintenance Guide

1312 Jordaan 3-SpeedAssembly & Maintenance Guide
Step 1: Attach the front fender
Referring to step 1 in the illustration, loosen the nut
and bolt (using the 2x 5mm allen keys) that runs
through the front fork and attach the fender, making
sure there’s enough space between the tyre and the
fender.
Step 2: Attaching the front stay to the front fork
Referring to step 2 in the illustration, attach the front
fender stay to the front fork, using the 3 or 4mm allen
key bolt
Step 3: Putting the wheel in place
Referring to step 3 in the illustration, put the wheel
in place and tighten the wheel nut using the 15mm
spanner
Now, on to the brakes.
02. Fitting the front wheel
and fender

1514 Jordaan 3-SpeedAssembly & Maintenance Guide
03. Aligning the brakes
Lift the wheel o the ground and give it a spin. It
should spin freely and without any noise. If you hear
a metallic rubbing sound, then the brakes will need
adjusting.
To do this, you’ll need to use the 5mm allen key. With
the bike upside down, adjust the caliper. You will
need to slightly loosen the two 5mm allen key bolts
(found on the top of the caliper), so that you can
gently move the caliper horizontally, allowing the disc
rotor to move freely between the brake pads.

1716 Jordaan 3-SpeedAssembly & Maintenance Guide
04. Fitting the
saddle and handlebars
Saddle.
Using the 5mm allen key, loosen the seatpost clamp
bolt and insert the seatpost. Make sure it’s at the
correct height. When sitting on the saddle, your knee
should be at a slight bend when the pedal is at its
lowest position. Then, tighten the bolt.
Tip: Using a 5mm allen key you can also adjust the
angle of the seatpost and the front-to-back position
of it. However, this should be correctly set already.
Handlebars.
Step 1: Now, using a 6mm allen key, loosen the bolt
located at the top of the handlebar stem, then insert
it into the frame. Once inserted, centre the handlebar
and stem and tighten it.

1918 Jordaan 3-SpeedAssembly & Maintenance Guide
Step 2: To adjust the angle of the handlebar, loosen
the allen bolts of the front plate until you can move
the handle bar freely. Once you’ve found your prefer-
red bar angle, tighten the bolt.
Tip: Should you wish to adjust the angles of your
grips, brakes and shifter, you can do so with a simple
turn of allen key 3 or 4.

2120 Jordaan 3-SpeedAssembly & Maintenance Guide
05. Fitting the pedals
To assemble the pedals, you will need a 15mm open-
ended spanner. Insert the pedal into the crank and
ensure the pedals are properly tightened.
LEFT pedal: this is the pedal that has indented hori-
zontal lines on the small part between the pedal and
thread.
RIGHT pedal: This pedal has no indented lines and is
smooth in between the pedal and thread
ATTENTION: please make sure you check the thread
direction before inserting the pedals. Fitting the pe-
dal to the wrong side can damage the crank arm and
is not covered under warranty.

2322 Jordaan 3-SpeedAssembly & Maintenance Guide
06. Finishing
Touches
Bell: Install the bell on your handlebars, in your pre-
ferred position. Generally, this is on the left hand
side, next to the brake lever.
Lights: Both the front and rear racks have mounting
points for lights.
Rear Light: The rear rack mounting point is located
at the very rear of the rack. Using the two 8mm bolts
supplied with the lights, mount them using the two
mounting holes and tighten.
Front Light:
Attach the front light to the light holder that’s atta-
ched to the front fork.
If you’ve purchased a front rack, the front light at-
taches to the light holder in the middle of the rack.
Using the nut and bolt provided, tighten the light
onto the xture.
Tip: Make sure you remove the plastic battery tab.
Tyres: Pump the tyres to 55-65 PSI
Accessories: If you ordered any accessories such as
racks or locks, don’t forget to t these too. They each
come with their own instructions and also have their
own mounting points.
Now, you’re good to go. Enjoy your ride, the
Amsterdam way!

2524 Jordaan 3-SpeedAssembly & Maintenance Guide
07. Safety
and warranty
We oer a 2-year warranty on our LEKKER frames.
Additionally, we supply you with 2 years warranty
on the components of our dierent models starting
on the day of purchase. This warranty is only for re-
placeable components. Unfortunately, our warranty
is not transferable (including when sold to another
consumer) and can only be used by the original buyer
of a LEKKER product. If you want to use the warran-
ty, please ensure you have your receipt and go to the
original shop in which you made your purchase.
There are cases when our warranty isn’t valid. Our
warranty doesn’t cover wear and tear, incorrect as-
sembly or maintenance. There’s no warranty in the
case of; damage caused by accidents, improper use
or negligence. Our warranty is also void if changes
are made to the original design of the LEKKER bike.
Please note: your frame number is located on the
bottom of the bike frame, near the bottom bracket.
This might be needed for insurance purposes.

Assembly & Maintenance Guide
Jordaan 3-Speed
Womens
Assembly &
Maintenance Guide
lekkerbikes.com