LELY Calm View Administrator Guide

www.lely.com Lely Industries N.V.
.
Installation & Operator manual
EN - English Original
5.1701.8500.0 -
Lely Calm
View

INTENTIONALLY BLANK
5.1701.8500.0 -
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
Trademarks, Copyright and Disclaimer 3
Trademarks, Copyright and Disclaimer
The information given in this publication is provided for information purposes only and does not
constitute an offer for sale. Certain products may not be available in individual countries and products
supplied may differ from those illustrated.
No part of this publication may be copied or published by means of printing, photocopying, microfilm or
any other process whatsoever without prior permission in writing by Lely Holding B.V. Although the
contents of this publication have been compiled with the greatest possible care, Lely cannot accept
liability for any damage that might arise from errors or omissions in this publication.
For more information on the right on exclusive use please refer to our trademark notice on www.Lely.
com.
Copyright © 2022 Lely Holding B.V.
All rights reserved
Lely Industries N.V.
Cornelis van der Lelylaan 1
3147 PB Maassluis
the Netherlands
Phone: [phone]
Fax: [phone]
Website: www.lely.com
in n o va to r s in a g ric u lt u re

INTENTIONALLY BLANK
5.1701.8500.0 -
4 Trademarks, Copyright and Disclaimer
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
List of Included Amendments 5
List of Included Amendments
Issue Date
(yy/mm)
Revision Chapter(s) Remarks
2021/07 -New release
in n o va to r s in a g ric u lt u re

INTENTIONALLY BLANK
5.1701.8500.0 -
6 List of Included Amendments
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
Preface 7
Preface
Manual Contents
This manual contains the information for the correct installation, setup and maintenance of the Lely Calm
View. The information in this manual is for operators and technicians:
•The operator uses the information to clean or replace the Lely Calm View.
•The technician uses the information to install and set up the Lely Calm View.
Study and understand this information thoroughly before you install or do
maintenance the machine. Failure to do so could result in damage to equipment or
personal injury. Please consult your local Lely service provider if you do not
understand the information in this manual, or if you need additional information.
Store this manual in a safe place for future reference.
All information in this manual has been compiled with care. Lely shall not be liable for errors or faults in
this manual. The recommendations are meant to serve as guidelines. All instructions, pictures and
specifications in this manual are based on the latest information that was available at the time of
publication. Your machine may comprise improvements, features or options that are not covered in this
manual.
Applicability
Model designation
The table below shows the type numbers of concentrate feeder for which this manual is applicable.
Model Type number
Lely Calm View 5.1701.0101.0
Software version
The description, operation and procedures in this manual are based on the following software versions:
•XXXXXX Horizon or higher.
•E-Link version 1.08R or higher.
•ADS3830 PCB; 01.09.0 or higher.
Standard Torque Loading of Parts
All the nuts, bolts and screws used on the machine are torque tightened to standard torque loadings
applicable to the construction materials used.
If a part has a non-standard torque loading, it is specified in the applicable part of the manual.
Registration
The Type and Serial Number Plate is attached to the top lid of the camera(2).
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
8 Preface
KEY: 1. Camera house - 2. Type and serial number plate - 3. Cover lid
Always include the type and serial number of your Lely Calm View when you contact your local Lely
service provider or order spare parts.
Figure 1. Type and Serial Number Plate
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
Preface 9
We suggest you complete the table below with the type and serial numbers of your Lely Calm View. This
makes sure you can easily find the information.
Type number
Serial number
Personnel Requirements
Risk of accident from insufficiently qualified personnel. Unqualified
personnel working on or in the danger zone of the machine can be the
cause of serious injuries and considerable damage to material.
•All activities must only be carried out by qualified personnel.
•Keep unqualified personnel away from the danger zones.
•Only persons who can be expected to carry out their job reliably are
authorized as personnel.
•Persons whose reactions are impaired, e.g. by drugs, alcohol
medications are not authorized to work with the machine.
Maintenance Authorization
Risk of accident from uncertified technicians.
Uncertified technicians doing maintenance on the machine can be the
cause of serious injuries and considerable damage to material.
Only technicians certified by Lely Industries are authorized to do
maintenance on the machine, except for the maintenance done by the
operator as indicated in the operator manual. If people who are not
certified by Lely Industries do maintenance on the machine, the
warranty on the machine becomes invalid.
Technician Training
All the technicians certified by Lely Industries have completed an approved training program, and passed
written and practical examinations during and at the end of the training program. The training is given by
Lely International or a specialist from the LSO and includes troubleshooting and corrective maintenance
of the machine.
During training, a trainee is permitted to work for up to a maximum of six months under close supervision
of a certified technician. A trainee can do work on the machine only in the presence of a certified
technician.
in n o va to r s in a g ric u lt u re
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.

5.1701.8500.0 -
10 Preface
Contact Number Local Service Provider
We suggest you write the telephone number and email address of your local service provider contact in
the table below. This makes sure you can easily find the information.
Telephone number
email address
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
Table of Contents 11
Table of Contents
1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
2 Intended Use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
3 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.1 Signal Icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
3.2 General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.3 Statement for Class A digital device acc. to FCC 15.105 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.4 Electrical Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
3.5 Installation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
3.6 Operating Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-3
4 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.1 Storage & Operational Environmental Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.2 Power Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
4.3 Camera Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
5 Description and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.1 Component description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
5.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
6 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2 Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2.1 Preparation by the Owner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
6.2.2 Preparation by the Lely Service Provider . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
6.3 Install the Lely View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
6.4 Set the Settings in the App . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-12
7 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
7.1 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
8 WEEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
8.1 WEEE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1
9 EC Declaration of Conformity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
in n o va to r s in a g ric u lt u re

INTENTIONALLY BLANK
5.1701.8500.0 -
12 Table of Contents
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
Introduction 1-1
1 Introduction
The Young stock monitoring camera system is an automated in line vision and image creation, processing,
management, viewing and data analysis.
The information in this manual is for the installation and operators. The operator uses the information to
program and operate the Lely Calm View. The operator also uses the information to do maintenance.
in n o va to r s in a g ric u lt u re

INTENTIONALLY BLANK
5.1701.8500.0 -
1-2 Introduction
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
Intended Use 2-1
2 Intended Use
The Lely Calm View is intended as an aid to the farming industry in the display, detection, counting and
classification of young stocks –young calves and heifers. The system is intended to operate in barn
conditions at a height between 1.8 m (5.9 ft) to 3.5 m (11.48 ft) above ground.
in n o va to r s in a g ric u lt u re

INTENTIONALLY BLANK
5.1701.8500.0 -
2-2 Intended Use
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
Safety 3-1
3 Safety
3.1 Signal Icons
Note the use of the signal words DANGER, WARNING and CAUTION with the safety messages. The signal
word for each message uses the following guidelines:
Danger
Indicates a hazardous situation which, if not avoided, will
result in death or serious injury.
Warning
Indicates a hazardous situation which, if not avoided, could result in
death or serious injury.
Caution
Indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
Notice
Is used to address practices not related to physical injury e.g. property
damage.
Tip
Indicates information that may help the reader, but not hazard related.
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
3-2 Safety
3.2 General Safety
When developing the Lely Calm View the latest standards were implemented to make this product as safe
as possible. However, there are a few additional rules that should be observed.
•Do not use the products in any way that might violate the integrity of others.
•Always follow the laws and legislations that apply in your country.
•Do not leave plastic packaging material near children or animals to avoid the risk of suffocation.
•Do not open the camera enclosure as it is a non-serviceable product.
•Lely resigns all responsibility that might occur from abuse or incorrect use of the products. Always
follow the instructions in this manual.
•Read and understand this manual and all safety signs before you install parts of the Lely Calm View.
•Only trained persons are permitted to operate the Lely Calm View.
•Always have the telephone number of the nearest medical centre close at hand.
•Contact your nearest Lely service provider if you have any questions.
3.3 Statement for Class A digital device acc. to FCC 15.105
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
3.4 Electrical Safety
•The Lely Calm View shall only be used in combination with an external approved (for example EN
61558-2-16 or EN 62368-1) power supply which has the required insulation barrier.
•Only an authorized electrician must install the electrical power supply for the system components.
•Only an authorized electrician may work on the electrical installation.
•Make sure the electrical grounding of the electrical system and all parts of the machine meet the local
rules and regulations.
•Keep all cables properly protected and out off reach of animals.
•Prevent damage by vermin.
•Replace any damaged electrical lines, conduits, switches and components immediately.
in n o va to r s in a g ric u lt u re

5.1701.8500.0 -
Safety 3-3
3.5 Installation Safety
•Always use a proper scaffold or a double sided ladder when you install the Lely Calm View or do
maintenance on the Lely Calm View.
•Always block the cow traffic when you install the Lely Calm View or do maintenance on the Lely Calm
View.
•Always follow local rules and regulations.
•Always use PPE (Personal Protective Equipment) according to the manufacturer specifications.
3.6 Operating Safety
•Do not look directly into the camera as it uses an IR laser (Class 1) during low light conditions.
in n o va to r s in a g ric u lt u re

INTENTIONALLY BLANK
5.1701.8500.0 -
3-4 Safety
in n o va to r s in a g ric u lt u re