LevelOne WAP-6121 User manual

1
WAP-6121
N300 PoE Wireless Access Point, Ceiling Mount,
Controller Managed
User’s Manual
V1. 0_20161110

2
Attention:
1. Check box contents:
Ceiling Wireless AP
LAN cable
QIG
Setting Screws
2. Warning:

3
Contents
Chapter 1 Hardware and Operation mode Instruction...............................................................4
1.1 LED indicator:..........................................................................................................................................4
1.2 AP Interface: .............................................................................................................................................4
1.3 Power Supply: ..........................................................................................................................................4
1.4 AP Installation:.........................................................................................................................................4
Chapter 2 Connect Wireless AP with PC:........................................................................................6
Chapter 3：Login.......................................................................................................................................7
Chapter 4 : WEB GUI interface Setting:..........................................................................................9
4.1 Status:.........................................................................................................................................................9
4.2 Wizard Configuration:..........................................................................................................................11
4.2.1 Gateway Mode:...........................................................................................................................................11
4.2.2 WiFi Repeater mode....................................................................................................................................13
4.2.3 WISP Operation mode: ...............................................................................................................................14
4.2.4 AP Operation mode:....................................................................................................................................16
4.3 Advanced Setting:..................................................................................................................................18
4.3.1 Device Status: .............................................................................................................................................18
4.3.2 Wireless Basic settings:...............................................................................................................................19
4.3.3 Virtual AP: ..................................................................................................................................................20
4.3.4 Access Control: ...........................................................................................................................................20
4.3.5 Advanced Settings:......................................................................................................................................21
4.3.6 Network: .....................................................................................................................................................21
4.3.7 Management:...............................................................................................................................................22
Chapter 5 Share Internet and Obtain IP address automatically......................................25
Chapter 6 Trouble Shooting:...........................................................................................................26
Appendix A LICENSE STATEMENT / GPL CODE STATEMENT............................27

4
Chapter 1 Hardware and Operation mode Instruction
P1
1.1 LED indicator:
Green: Power Indicator
Blue: WiFi Indicator
1.2 AP Interface:
RST: Reset Button, it make AP revert to default data after press it 15 seconds.
WAN: WAN Port, connect with ADSL modem or Internet mainly. It will be LAN port under Wireless AP and
WiFi Repeater operation mode
LAN: LAN Port to end users
LED: LED Indicator of WAN port and LAN port
DC: DC power connector
1.3 Power Supply:
The connection diagram shows as P2, Internet cable from PoE Switch to Ceiling AP’s WAN Port, then PC
access into ceiling AP wired/wireless.
Pls note the PD wireless AP support 48V IEEE 802.3af standard PoE, the PoE switch should comply with
802.3af 48V PoE standard.
P2
1.4 AP Installation:
For the Ceiling Wireless AP, will be installed under ceiling based on following steps:

5
P3 AP installation

6
Chapter 2 Connect Wireless AP with PC:
Use can connect the PC with wireless AP by Wireless SSID and LAN cable:
The diagram of wireless connection showed as follow:
Pls note: the default SSID is LevelOne, SSI D’s pa ssw ord i s 66 666 66 6
The diagram of LAN cable connection showed as follow:
P4 Connection way

7
Chapter 3：Login
The necessary information about log in is displayed on the sticker of the product, including the URL, User
Name and Pass Word
1）Connect the Ceiling AP with computer
2）Configure the PC’s local connection IP address as 192.168.188.X (X is number from 2 to 252), subnet
mask is 255.255.255.0, follow P5 and P6 to finish.
P5 Setting of computer’s IP address
P 6Setting of computer’s IP address

8
3) Input 192.168.188.253 into IE browser, then pop up the login page, the default login password: admin, then
login, pls do following P7
P7 Login
4) After login, then P8 Device Status will be showed;
This page will show the Wireless AP’s default operation mode, channel, connection status, CPU usage,
Wireless settings, LAN Setting, Wireless AP’s Location, hardware/firmware version.
P8: Device Status

9
Chapter 4 : WEB GUI interface Setting:
4.1 Status:
After login, then P9 Device Status and home page will be showed:
P9: Device Status
In this page, show the AP’s default operation mode, channel, end user QTY, connection status, CPU usage
status, Wireless, LAN and AP location info.
Then in Wireless Setting, GUI configuration page showed as below:
User can configure the SSID, password, band width, channel here, then Apply to finish.
P10. Wireless setting

10
LAN Setting to configure the DHCP or Fix IP
P11 LAN Setting
AP location setting: can mark where the AP set up, and AP name as P12:
P12AP Postion setting

11
4.2 Wizard Configuration:
Wizard: It instruct users to configure wireless AP’s operation mode based on needs: there are four operation
mode including gateway, repeater, WISP, Wireless AP. Please confirm the operation mode first before configuration
starting.
Click Wizard in Status page, will pop up following page to configure the operation mode and there are explanation
for each operation mode for better application.
P13 Operation mode
4.2.1 Gateway Mode:
Before Click Gateway mode, confirm your internet will be static IP, PPPoE, or DHCP:
Then will pop up following picture after click it, Please choose the right WAN setting mode, then click next to
continue.
P14. WAN setting in Gateway Mode

12
P15 Wireless Setting in Gateway Mode
When click Next, then will complete the Gateway mode setting and show following picture:
P16 Complete the setting in Gateway Mode
When return to Status, will show wireless router’s SSID, internet connection, LAN connection status showed as
follow:

13
P17 Status in Gateway Mode
4.2.2 WiFi Repeater mode
A. Login the Web management page, click “Wizard”, then “WiFi Repeater”
B. Select the AP’s SSID want to bridge, take “wireless 2.4G” for example, then input the AP’s key, click next to
complete.
P18 Repeater Mode
Click Return button, will back to Status, show Repeater mode data, show fail or success, and user can configure
this data in this page if required.

14
P19 Status in Repeater Mode
In wifi repeater operation mode, the default is SSID disable. If want to enable SSID, then click Wireless
Setting. Pls note, when click wireless relay setting, following page will pop up, you can make change from here
easy:
P20 Wireless Relay Setting
4.2.3 WISPOperation mode:
Click WISP operation mode in Wizard, then will pop up the configure page, pls set the WISP operation mode based
on the steps showed in picture:

15
P21 WISP Mode
Configure the right WAN setting in WISP operation mode, then next to complete
P22 WAN setting in WISP mode
Then complete and back to status, will show the connection fail or success, then can configure the data based
on request:

16
P23 Status in WISP mode
Remark: When click WAN Setting, will pop up following picture to ask you choose PPPoE, DHCP or Static IP
P24 WAN setting in WISP mode
4.2.4 APOperation mode:
Set the wireless data, AP Location info as required, then click next to continue and enter into LAN setting.
After LAN setting, complete the AP mode configuration and back to Status:

17
P25 Wireless setting in AP Mode
P26 LAN Setting in AP Mode

18
P27 Status in AP Mode
4.3 Advanced Setting:
In advanced setting, mainly for wireless AP’s device status, wireless setting, Networking setting and AP
management configure.
Let’s Click Advanced Setting in status page, will show return home, Setup Wizard which we showed before.
Let’s shown more in Device Status, Wireless, Network and Management in following pages:
4.3.1 Device Status:
to show the Wireless AP’s status, Wireless Status and LAN status.
In status, mainly to check the ceiling wireless AP’s firmware version, hardware version, uptime info.:
P28 Device Status

19
In wireless status, to show wireless AP’s SSID, MAC address for WiFi, Channel, Encryption, Client List info.
P29 Wireless Status
In LAN Status, we can check wireless AP’s IP address, Subnet Mask, LAN MAC address and other info
showed in following picture.
LAN Status
4.3.2 Wireless Basic settings:
For wireless basic settings, mainly to configure the wireless SSID, password, band width ,encryption,
channel, Multi SSID.

20
P31 Basic Setting in Wireless
4.3.3 Virtual AP:
There are 3 virtual AP in 2.4G wireless, if need do multi SSID, then users can configure it showed in following
picture:
P32 Virtual AP
4.3.4 Access Control:
Allow or deny the users access into this wireless AP based on MAC address.