Leviton Quantran QTM00-050 User manual

mBus Control Stations
Cat. Nos. QTM00-050 (5-Button), QTM00-090 (9-Button)
INSTALLATION ENGLISH
DI-000-QTM00-00A
DESCRIPTION
Leviton Quantran mBus control stations are a flexible, easy to configure control interface to Quantran mBus load control devices. Offered in multiple scene
configurations and finishes, a device is available to fit every lighting control need.
WARNINGS AND CAUTIONS
• WARNING: TO AVOID SERIOUS PERSONAL INJURY never push
objects of any kind into this product through openings, as they may touch
dangerous voltages.
• WARNING: TO AVOID SERIOUS PERSONAL INJURY never touch
uninsulated wires or terminals unless the wiring has been disconnected at
the network interface.
• Read and understand all instructions. Follow all warnings and instructions
marked on the product.
WARNINGS AND CAUTIONS
• Never install communications wiring or components during a lightning storm.
• Never install communications components in wet locations unless the
components are designed specifically for use in wet locations.
• Use caution when installing or modifying communications wiring or
components.
• Do not use this product near water - e.g., near a tub, wash basin, kitchen
sink or laundry tub, in a wet basement, or near a swimming pool.
• SAVE THESE INSTRUCTIONS.
Raise
Lower
IR Receiver
Off
Clip on
Face plate
B1
B2
B3
B4
Buttons
1-8
Raise
Lower
IR Receiver
Off
Clip on
face plate
• Connect Data+, Data-, Common, +V, and shield at every station (see
Table 1).
• Do not splice control wire
• Shield shall be connected to ground at the dimmer rack and must only be
connected to ground at one point in the system.
• Capacitance of wire shall be 15pF/ft. or less.
• Normal Impedance of wire shall be between 100-120 ohms.
• A second pair of stranded wire is required for the power.
• We strongly recommend the use of either Leviton #WIRLN-500, Belden
1502R, or equivalent be used for wire runs.
Table 1
Pin # Function Notes
1 Data + Connect on every station, use one conductor of a twisted pair
2 Data - Connect on every station, use the second conductor of a twisted pair
3 Common Connect on every station – even if not using power
4 +V +12-24Vdc
Use RS485 compatible cable for communications. RS-485 requires a single
Twisted Pair, 24 AWG minimum.
TERMINATIONS
• Scene buttons are used to recall pre-programmed scenes. Reference
dimmer modules installation instructions for details on programming.
• Raise/Lower buttons are used to raise or lower the last selected scene.
• Off turns the lights off.
• The IR Receiver can be used with the IR remote to execute the above
functions.
OPERATION
Input: mBus Stations Require 8-18VDC
Current draw: 10mA
Standard dc Voltage Drop calculations should be used to ensure that your
voltage is always greater than the minimum. If you’re using 18AWG Belden
1502R with a resistance of 0.0069ohms/foot, the following formula can be
used:
Vdrop=Total Load (Amps) * Run Length (Feet) * 0.0069 Ohms/Foot
NOTE: Assuming you’re using a 12Vdc Supply, and you’ll allow a voltage drop
of 12V-8V=4V, the formula can be simplified to:
Max Run (Feet) =4/(Total Load (Amps)*0.0069)
POWER CONSIDERATIONS
NOTE: The mounting surface must be flat to avoid distortion of the back plate,
which may prevent the cover plate fitting correctly. For the same reason, do
not over-tighten the fixing screws.
INSTALLATION
• Product is designed to fit into a single gang 3” x 3” back box, not included.
• Follow best industry practices for installation
• Product requires commissioning by a Leviton field commissioning agent
after installation.
QTM00-050
QTM00-090
WEB VERSION

DI-000-QTM00-00A
www.leviton.com
For Technical Assistance 1-800-959-6004
[email protected]
LIMITED 2 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the time of its sale by Leviton is free
of defects in materials and workmanship under normal and proper use for two years from the purchase date. Leviton’s only obligation is to correct
such defects by repair or replacement, at its option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes and
there is disclaimed liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly or in an
improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used under normal operating conditions or not
in accordance with any labels or instructions. There are no other or implied warranties of any kind, including merchantability and fitness for a
particular purpose, but if any implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to two years. Leviton is not liable for incidental, indirect, special, or consequential
damages, including without limitation, damage to, or loss of use of, any equipment, lost sales or profits or delay or failure to perform this
warranty obligation. The remedies provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
© 2014 Leviton Mfg. Co., Inc.
Copyright and Trademark Information
This document and all its contents herein are subject to and protected by international copyright and other intellectual property rights and are the property of
Leviton Manufacturing Co., Inc, its subsidiaries, affiliates and/or licensors.
Use herein of third party trademarks, service marks, trade names, brand names and/or product names are for informational purposes only, are/may be the
trademarks of their respective owners; such use is not meant to imply affiliation, sponsorship, or endorsement.
No part of this document may be reproduced, transmitted or transcribed without the express written permission of Leviton Manufacturing Co., Inc.
Quantran is a registered trademark in Australia, Bahrain, China P.R., Great Britain, Hong Kong, India, Jordan, Kuwait, Malaysia, New Zealand, Oman, Qatar,
Saudi Arabia, South Africa, Vietnam, and other countries pending.
Common
(Belden 1502 Black)
Data +
(Belden 1502 Blue)
Data -
(Belden 1502 White)
+V
(Belden 1502 Red)
Shield
Mode
Common
(Belden 1502 Black)
Data +
(Belden 1502 Blue)
Data -
(Belden 1502 White)
+V
(Belden 1502 Red)
Shield
Terminate
WIRING DIAGRAMS
WEB VERSION