Leviton 5R1UD-S12 User manual

Instructions for Use - Opt-X®UHD Fiber Optic Enclosure
Leviton Network Solutions, a division of Leviton Mfg. Co., Inc.
2222 - 222nd St. SE Bothell, WA 98021 Tech Line: 1-800-722-2082 Fax: [phone] www.leviton.com
Copyright © 2008 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
Page 1 of 30
DI-000-5RXUD-20A
5R1UD-S12
5R2UD-S24
5R4UD-S48
5R1UD-S12 5R2UD-S24
5R4UD-S48

FIBER CONNECTOR SAFETY WARNINGS
SAFETY INFORMATION
1. Always wear safety glasses.
2. Isopropylalcoholisammableandmaycauseeyeirritation.Incaseofcontactwitheyes,
 ushwithwaterforatleast15minutes.Whenusingisopropylalcohol,alwaysassure 
proper levels of ventilation. In case of ingestion, consult a physician immediately.
3. Never look directly into a laser light source, point source at a person’s eyes, or point
 sourceatreectivesurfaces.
4. Whenworkingonaberlink,alwaysturnlasersourceoff,ordisconnectcompletely.
5. Alwaysdisposeofberdebrisproperly,preferablyusingstickytabs.
6. Do not place food or beverages in the vicinity of the work area.
7. Thoroughlywashfaceandhandsafterterminatingber.
8. Carefullyremoveanyberdebristhatmayhavebeenstucktoclothing,orleftinwork
area, and dispose of properly.
TIPS AND RECOMMENDATIONS
1. Usingisopropylalcohol,thoroughlycleanexposedberandbufferensuringbotharefree
from dust, oil, and debris.
2. Do not lay ferrule dust covers on a dirty or dusty surface.
3. Alwaysusepropertoolsand/oraccessoriestoterminatebersandcleanconnectortips.
TABLE OF CONTENTS
The following instructions will help you quickly install your Leviton Opt-X®Ultra High Density System Enclosure for
use in your equipment cabinet or rack. For detailed information on each step, go to the page number listed below.
Safety and Installation Instructions Pg. 2
Table of Contents Pg. 2
Standard Accessories Pg. 3
Optional Accessories Pg. 3
Equipment Overview Pg. 3
Product Views Pg. 4
Mounting, Front Door Operation, and Rear Door Operation Pg. 5
Cable Installation - Preparation Pg. 6
Cassette Installation and Removal Pg. 7
Cable Installation - Applications Pg. 8
Front side patch cable routing, Opt-X®Ultra High Density System Labeling Pg. 9
Page 2 of 30 DI-000-5RXUD-20A

STANDARD ACCESSORIES (Included with Opt-X UHD™ Enclosure)
Prior to installing your Leviton Opt-X UHD Enclosure, please refer to the table below. This will help ensure that you
have all the items shipped with the unit, and/or any additional items that may be required for proper installation.
Page 3 of 30 DI-000-5RXUD-20A
Description Part Number
Universal Opt-X Cable Clamp Kit, Single Cable Grommet (for enclosure mounting) 5RCMP-KIT
Universal Opt-X Cable Clamp Kit, Multiple Cable Grommet (for enclosure mounting) 5RCMP-KT2
Universal Opt-X Cable Clamp Kit, Single and Multiple Cable Grommet (for rack/post mounting) 5RCMR-KIT
1RU Mounting Ear for 23" Rack 5REAR-023
Grounding Kit DPGRD-KIT
1RU Brush Guard (Bag of 2) 5RBSH-1UN
2RU Brush Guard (Bag of 2) 5RBSH-2UN
OPTIONAL ACCESSORIES
Description Image Quantity in
1RU Kit
Quantity in
2RU Kit
Quantity in
4RU Kit
ID Card Label 1 1 1
Velcro Tie 4 6 6
Rack Mnt Screw 4 4 4
12
11
10
9
4
8
7
6
23
2
45
3 5 6
9
5
10 11
6
12 1
1
2
45
3
67
4
8
10 11
6
12 1
1
235
3
67
4
89
5
D
C
1
1
23
2
4
4
89
5
10 11
6
12
2
4
A
5
3
6
B
7
1
2
1
1
23
Panel # Serving: Fed From:
4
89
5
10 11
6
12
2
4
A
5
3
6
B
7
1
2
1
1
23
4
89
5
10 11
6
12
2
45
3
67
1
1
23
4
89
5
10 11
6
12
2
4
C
5
3
6
D
7
1
2
1
1
23
4
89
5
10 11
6
12
2
45
3
67
1
1
23
Panel# Serving: FedFrom:
EQUIPMENT OVERVIEW
Description
TheUHDEnclosureisanultra-highdensityberopticsystemdesignedforusewithHDXcassettes,
adapter plates and blanks.
Provided Parts
1. (1) 1RU, 2RU or 4RU UHD Fiber Optic Enclosure
2. (3, 6 or 12) Slide Out Trays respectively.
3. (1) Rear lid on 1RU and 2RU models
4. (2) Mounting ears with screws on 1RU, (4) Mounting ears with screws on 2RU and 4RU
5. (1) 12/24x0.5L” screw kit assembly
6. (1) Accessory Kit
7. (1) Label Designation Card kit

SIDE VIEW (2RU Shown)
1. 19” rack mount brackets
2. Cable Clamp kit mounting points
NOTE: Optional 23" RM kit also available for 1RU. See
Optional Part Number list (see page 4).
Page 4 of 30
DI-000-5RXUD-20A
1. Front Door
2. Rear Lid (Removable on 1RU and 2RU only)
3. Mounting Ears
4. Brush Guard (Sold Seperately)
5. Front Grab Bar (pull to slide each tray forward)
1. Rear Cable Management mesh
2. Opt-X Clamp Kit (Sold Seperately)
3. Hook and Loop lacing points
4. Cable Management Guides
5. Sliding termination tray
6. Front Grab Bar (pull to slide each tray forward)
Interior
NOTE: Cover removed for clarity.
Exterior
5.
1.
3.
4.
2.
PRODUCT VIEWS
6. 5.
1. 3.
2.
4.
1.
2. 2.

Page 5 of 30
DI-000-5RXUD-20A
To remove the Rear Door:
1. Pull plungers out to dis-engage
2. Remove lid rearward
To open the Front Door:
1. Push Release Latches downward
2. Open Door
FRONT DOOR OPERATION REAR DOOR OPERATION (1RU and 2RU ONLY)
NOTE: Rear Door on 4RU enclosure operates
identically
NOTE: Ensure plungers are dis-engaged prior to
installation of lid
MOUNTING AN ENCLOSURE
NOTE: Thread each screw a minimum of three full
rotations before mounting
Install remaining screws and hand tighten all

CABLE INSTALLATION - PREPARATION
Page 6 of 30 DI-000-5RXUD-20A
Top View: Tray to Front
NOTE: Tray in forward position, covers
are removed for clarity. COMMENTS:
• Routecabletotraythroughgrommetontheopposite
side of slide tray tie down point
• Assurecableslackfortraymovement.
• Recommendedtrunkbreakoutlengthis36inches.
• Aminimumof20inchesoffreeslackisrequiredtoeach
cassette for bend radius compliant accessibility from the
front side.
To remove tray from enclosure, slide tray fully forward
stop position. Press release lever and slide tray out to
remove.
Pictured:Removabletraytofacilitateeld
termination
Tray Release
To Remove a tray: (see diagram)
1. Pull the tray forward to the stop point
2. Press the release lever toward the outside of the
enclosure and remove the tray from the tray
guides.
To Install a tray:
A. Insert the tray into the target position
B.Slidethetrayinwarduntiltherststoppointis
reached.
C. Press the release lever toward the outside of the
enclosure and continue sliding the tray inward to
the fully enclosed position.
Caution-Damagemayoccurtobercablingiftrayisremoved
beyond the stop point when loaded.

CASSETTE INSTALLATION AND REMOVAL
Page 7 of 30
DI-000-5RXUD-20A
Insert HDX Cassettes, Adapter Plates or Blank Plates from the front into the
receiving guide of the target location.
HDX Cassette HDX MTP Cassette
HDX Blank PlateHDX Adapter Plate

Page 8 of 30 DI-000-5RXUD-20A
CABLE INSTALLATION - APPLICATIONS
Rear Routing Guide Right
Rear Routing Guide Breakout

OPT-X UHD LABELING
Page 9 of 30 DI-000-5RXUD-20A
Label Printing Organization by Fiber Cassette or Adapter Panel Type
Per Column Number Scheme
Port Spacing No. of Ports
Duplex SC (3 pack) .60 6 1 2 3 4 5 6
Quad LC (3 pack) .60 12 1-2 / 3-4 5-6 / 7-8 9-10 / 11-12
MTP (3 port) 1.20 3 1 Space 2 Space 3
MTP (6 port) .60 6 1 2 3 4 5 6
Universal Labeling Devices
1RU
 •Use1/4"labeltape
 •Totallabellength~ 4"
 •Eachpanelsectionis1/4"Hx3/4"L
Leviton has provided the labeling model requirements to Rhino Labeling. Rhino has established product standards which are
available at www.rhinolabeling.com
2RU
 •Use3/8"labeltape
 •Totallabellength~ 3 3/4"
•Eachpanelsectionis3/8"Hx5/8"L
FRONT SIDE PATCH CABLE ROUTING
Tomaintainproperbendradiusandprotectbersfromdamageduringmovementofslidingtrays,followtherecommended
patch cord load orders as shown.

Leviton Manufacturing Co., Inc.
2222 222nd ST SE
Bothell, WA 98021, USA
Technical Support: 800-824-3005
Page 10 of 30 DI-000-5RXUD-20A