Leviton Opt-X 1000i User manual

Instructions for Use - Opt-X®1000i Enclosure
Leviton Network Solutions, a division of Leviton Mfg. Co., Inc.
Tech Support: 1.800.824.3005 E-mail: [e-mail] Web: www.leviton.com
Copyright © 2011 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
MTP®is a registered trademark of US Conec, Ltd.
Page 1 of 8
PK-93777-10-02-0C
5R1UM-F03, 5R1UM-S03, 5R2UM-F06,
5R2UM-S06, 5R3UM-F09, 5R3UM-F12,
5R4UM-F12, 5R4UM-F15
5R1UM-*03
5R2UM-*06 5R3UM-F**
5R4UM-F**

FIBER CONNECTOR SAFETY WARNINGS
SAFETY INFORMATION
• Always wear safety glasses.
• Isopropylalcoholisammableandmaycauseeyeirritation.Incaseofcontactwitheyes,ushwithwaterforatleast
15 minutes. When using isopropyl alcohol, always assure proper levels of ventilation. In case of ingestion, consult a
physician immediately.
• Never look directly into a laser light source, point source at a person’s eyes, or point sourceatreectivesurfaces.
• Whenworkingonaberlink,alwaysturnlasersourceoff,ordisconnectcompletely.
• Alwaysdisposeofberdebrisproperly,preferablyusingstickytabs.
• Do not place food or beverages in the vicinity of the work area.
• Thoroughlywashfaceandhandsafterterminatingber.
• Carefullyremoveanyberdebristhatmayhavebeenstucktoclothing,orleftinworkarea, and
dispose of properly.
TIPS AND RECOMMENDATIONS
• Usingisopropylalcohol,thoroughlycleanexposedberandbufferensuringbotharefreefrom dust, oil,
and debris.
• Do not lay ferrule dust covers on a dirty or dusty surface.
• Alwaysusepropertoolsand/oraccessoriestoterminatebersandcleanconnectortips.
QUICK START GUIDE
The following instructions will help you quickly install your Leviton Opt-X®1000i Enclosure for use in your equipment
cabinet or rack. For detailed information on each step, go to the page number listed below.
Safety and Installation Instructions Pg. 2
Quick Start Guide Pg. 2
Equipment Overview Pg. 3
Standard Accessories Pg. 4
Optional Part Numbers Pg. 4
Side View Pg. 4
Cover Removal, and Installation Pg. 5
Cable Installation - Preparation Pg. 5
Opt-X®1000i Fiber Management Ring Pg. 6
Opt-X®1000i Labeling Pg. 7
Cable Installation - Applications Pg. 8
Page 2 of 8 PK-93777-10-02-0C

Page 3 of 8
PK-93777-10-02-0C
1. Removable Covers
2. Removable Cable Grommet
3. Bend Radius Adapter
4. Adjustable Mounting Ears
1. Hook & Loop Lacing Points (For Splice Trays)
2. Cable Lace Points
3. Splice Tray Alignment Pin
4. 1/4 Fiber Cable Management Ring
5. Bulkhead Brackets (Opt-X®= Black, LGX = Gray)
6. Patch Cord Cable Managment Rings
7. Lock (optional)
8. Connector Removal Access Points
9. Ground Lug Mounting Hole
EQUIPMENT OVERVIEW - FIXED & SLIDING TRAY
INTERIOR
NOTE: Covers removed for clarity.
Fixed With Sliding Tray
EXTERIOR
Fixed With Sliding Tray
1. Removable Covers
2. Removable Cable Grommet
3. Bend Radius Adapter
4. Slide Out Termination Tray
5. Adjustable Mounting Ears
1. Hook & Loop Lacing Points (For Splice Trays)
2. Cable Lace Points
3. Splice Tray Alignment Pin
4. 1/4 Fiber Cable Management Ring
5. Bulkhead Brackets (Opt-X®= Black, LGX = Gray)
6. Patch Cord Cable Managment Rings
7. Lock (optional)
8. Connector Removal Access Points
9. Rear Tray Plunger (lift plunger to slide tray backward)
10.Front Tray Plunger (lift plunger to slide tray forward)
11.Ground Lug Mounting Hole
1.
2.
3.
4.
5.
6.
7.
8.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
1.
1.
2.
3.
4.
1.
1.
3.
2.
4. 5.
11.
9.

Page 4 of 8
PK-93777-10-02-0C
STANDARD ACCESSORIES (Included with Opt-X®1000i Enclosure)
Prior to installing your Leviton Opt-X®1000i Enclosure, please refer to the table below. This will help ensure that
you have all the items shipped with the unit, and/or any additional items that may be required for proper installation.
Description Image Quantity in
1RU Kit
Quantity in
2RU Kit
Quantity in
3RU Kit
Quantity in
4RU Kit
Self Adhesive Label 2 2 2 2
Spiral Loop, 18" 1 1 0 0
Cable Tie 4 4 6 6
Rack Mount Screw 4 4 4 4
Ground Lug 1 1 1 1
OPTIONAL PART NUMBERS
Description Part Number
Universal Opt-X® Clamp Kit for Enclosure Mounting 5RCMP-KIT
Universal Opt-X® Clamp Kit for Rack Mounting 5RCMR-KIT
Fiber Cable Management 1/4 Ring Kit (bag of four 1/4 rings) 5R100-14R
Splice Tray Mounting Hardware Kit SPLMT-HKT
1RU Mounting Ear for 23" Rack 5R1RU-023
Lock & Key 5L000-LOK
SIDE VIEW (1RU Shown)
1. Adjustable 19" rack mount brackets
2. Cable Clamp kit mounting points
3. Cut grommet as needed to accomodate cables.
NOTE: 2RU and 4RU brackets are reversible for mounting onto 23" racks. Optional 23" RM kit also available for 1RU.
See Optional Part Number list above.
1.
2. 2. 3.

Page 5 of 8
PK-93777-10-02-0C
To open the door: Lift tabs as shown
To remove cover: Push tabs down, and
then slide the cover out.
COVER REMOVAL DOOR LATCH
CABLE INSTALLATION - PREPARATION (SLIDING TRAY)
Multi-Strand
Secure to Enclosure
Secure to Tray
Top View: Tray to Front
NOTE: Tray in forward position, covers
and center bar removed for clarity.
NOTE:
• Routecabletotraythroughgrommetontheopposite
side of cable entry.
• Planforcableroutingpriortotermination.
• Adjustberringkitbasedondesiredapplication(see
page 6 for detail).
• Assurecableslackfortraymovement.
• Foradditionalcableslackmanagement,useoptional
Fiber Management Ring Kit (5R100-14R).
To remove tray from enclosure, lift rear tray plunger, slide tray
fully rearward.
Pictured:Removabletraytofacilitateeld
termination and splicing
NOTE: Grounding lug can be used to secure
cable to enclosure.
Caution:
If grommet needs to
be cut, cut at an angle
towards the center
and on the inside of
the grommet only.
NOTE: Cutting beyond the pre-determined cutting
guides or through the grommet edge may cause
deformation of the grommet and decreased retention
capability.
CABLE GROMMET

Page 6 of 8 PK-93777-10-02-0C
Opt-X®1/4 FIBER CABLE MANAGEMENT RING (Removal, Installation and Assembly)
Opt-X® Fiber management ¼ rings are pre-installed at the factory. To remove, grip the ¼ ring, lift the Position-
Locking Tab, turn counter clockwise until unlocked, and then lift to remove. When removing a half or full
management ring group, simultaneously lift the 2 or 4 Position-Locking Tabs, turn counter clockwise until unlocked,
and then lift to remove.
RING STACKING
Position initial ring unit (¼, ½, or full) upside
downonaatsurface.Positionadditional
ring upside down above initial ring and
presstogetherusingsufcientforceto
engage stack locking device.
CAUTION – always perform stacking
before installing ring unit into tray.
HALF RING ASSEMBLY
Hold a ¼ ring unit in each hand, bring the units
together and engage by placing the tab of the left
unit into the slot of the right unit.
HALF RING INSTALLATION Position ½ ring unit
overouterringslotssothealignmenttabstinto
slots. Press down and turn the ½ ring unit clock-
wise to engage tabs and lock into position.
CAUTION – when installing into a tray that is in the
enclosure, provide adequate support under the tray
by placing a hand under the ring slot area.
FULL RING ASSEMBLY
Hold a ½ ring unit in each hand, bring units together
with tabs above slots, rotate to engage tabs.
FULL RING INSTALLATION Position full ring unit
overinnerandouterringslotssoalignmenttabst
into slots. Firmly press down and turn the full ring
unit clockwise to engage tabs and lock into position.
CAUTION – when installing into a tray that is in the
enclosure, provide adequate support under the tray
by placing a hand under the ring slot area.
HALF RING ASSEMBLY FULL RING ASSEMBLY RING STACKING
Tab
Stacking/Locking
Device (Upper)
Stacking/Locking
Device (Lower)
Slot
RING OVERVIEW RING SIDE PROFILE RING ALIGNMENT SLOTS
Position-Locking Tab
Turn
Push

Opt-X®1000i LABELING (forfront&rearidenticationonenclosure)
Label Printing Organization by Fiber Adapter Type
Horizontal Orientation
Adapter No. of Ports Number Scheme
Duplex SC
(3 pack) 6 1 2 3 4 5 6
Duplex SC
(6 pack) 12
3-4 7-8 11-12
1-2 5-6 9-10
Duplex LC
(6 pack) 12
2 4 6 8 10 12
1 3 5 7 9 11
Quad LC
(6 pack) 24
5-6 / 7-8 13-14 / 15-16 21-22 / 23-24
1-2 / 3-4 9-10 / 11-12 17-18 / 19-20
ST/FC (6 pack) 6 1 2 3 4 5 6
ST/FC (8 pack) 8 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8
Label Printing Organization by Fiber Adapter Type
Vertical Orientation
Adapter Duplex SC
(3 pack)
Duplex SC
(6 pack)
Duplex LC
(6 pack)
Quad LC
(6 pack)
ST/FC
(6 pack)
ST/FC
(8 pack)
No. of
Ports 6 12 12 24 6 8
Number Scheme
1
1-2 3-4
1-2
1-2
3-4
5-6
7-8
11
2
3
4
5
6
7
8
2 3-4 2
3
5-6 7-8
5-6
9-10
11-12
13-14
15-16
3
4 7-8 4
5
9-10 11-12
9-10 17-18
19-20
21-22
23-24
5
6 11-12 6
Page 7 of 8
PK-93777-10-02-0C
5R1UM-F03, 5R1UM-S03
5R3UM-F09
5R3UM-F12, 5R4UM-F12
5R2UM-F06, 5R2UM-S06
Horizontal orientation
•Use3/8”or3/4"labeltape,
depending on adapter plate
•Totallabellength=4"
•Panelsectionis3/4"Hx4"L
Vertical orientation
•Use3/8”or3/4"labeltape, 
depending on adapter plate
•Totallabellength=23/4"
•Panelsectionis3/4"Wx23/4"H
5R4UM-F15
NOTE: Ensure that the label surface area is clean of dirt, oil,
and debris. Recommend use of isopropyl alcohol or a simple
soap and water solution when wiping down surface area.
UNIVERSAL LABELING DEVICES

CABLE INSTALLATION - APPLICATIONS (Typicalinstallations-notspecictoenclosure)
Utilizing MTP® Cassettes
Utilizing Splice Trays Utilizing Fan-Out Kits
Utilizing Pre-Terminated Cables or Field
Termination of tight-buffered cable
Page 8 of 8
PK-93777-10-02-0C