Leviton Opt-X 500i User manual

Instructions for Use - Opt-X®500i Enclosure
Leviton Network Solutions, a division of Leviton Mfg. Co., Inc.
Tech Support 1.800.824.3005 E-mail: [e-mail] Web: www.leviton.com
Copyright © 2011 Leviton Manufacturing Co., Inc. All rights reserved. Subject to change without notice.
MTP®is a registered trademark of US Conec, Ltd.
Page 1 of 6
PK-93776-10-02-0B
5R1UL-F03
5R2UL-F06
5R3UL-F12
5R1UL-F03
5R2UL-F06 5R3UL-F12

FIBER CONNECTOR SAFETY WARNINGS
SAFETY INFORMATION
• Always wear safety glasses.
• Isopropylalcoholisammableandmaycauseeyeirritation.Incaseofcontactwitheyes,ushwithwaterforat
least 15 minutes. When using isopropyl alcohol, always assure proper levels of ventilation. In case of ingestion,
consult a physician immediately.
• Never look directly into a laser light source, point source at a person’s eyes, or point sourceatreective
surfaces.
• Whenworkingonaberlink,alwaysturnlasersourceoff,ordisconnectcompletely.
• Alwaysdisposeofberdebrisproperly,preferablyusingstickytabs.
• Do not place food or beverages in the vicinity of the work area.
• Thoroughlywashfaceandhandsafterterminatingber.
• Carefullyremoveanyberdebristhatmayhavebeenstucktoclothing,orleftinworkarea, and
dispose of properly.
TIPS AND RECOMMENDATIONS
• Usingisopropylalcohol,thoroughlycleanexposedberandbufferensuringbotharefreefrom dust, oil,
and debris.
• Do not lay ferrule dust covers on a dirty or dusty surface.
• Alwaysusepropertoolsand/oraccessoriestoterminatebersandcleanconnectortips.
QUICK START GUIDE
The following instructions will help you quickly install your Leviton Opt-X®500i Enclosure for use in your equipment
cabinet or rack. For detailed information on each step, go to the page number listed below.
Safety and Installation Instructions Pg. 2
Quick Start Guide Pg. 2
Equipment Overview Pg. 2
Standard Accessories Pg. 3
Cover Removal & Optional Parts Pg. 3
Port ID Labeling Pg. 4
Fiber Ring Installation, Removal & Assembly Pg. 5
Typical Applications Pg. 6
1. Splice Tray Alignment Pin
2. Fiber Cable Management Ring
3. Hook and Loop Lacing Points for securing Cable
4. Removable Cover / Rear Door
5. Cover / Door Locking Pins
6. Hook and Loop Lacing Points for securing splice trays
7. Cover / Door Locking Pin Attachment Mounting Tabs
8. Rear Cable Entry Points
9. Optional Strain Relief Kit Enclosure Mounting Points
10. Adapter Plate Mounting Positions
11. Label Mounting Position
Page 2 of 6 PK-93776-10-02-0B
EQUIPMENT OVERVIEW
Interior/Exterior
NOTE: Cover removed for clarity.
1
2
3
4
5
6
7
8
9
10
11

Page 3 of 6
PK-93776-10-02-0B
STANDARD ACCESSORIES (Included with Opt-X®500i Enclosure)
Prior to installing your Leviton Opt-X® 500i Enclosure, please refer to the table below. This will help ensure that you
have all the items shipped with the unit, and/or any additional items that may be required for proper installation.
Description Image Quantity in 1RU
Kit
Quantity in 2RU
Kit
Quantity in 3RU
Kit
Cable Tie 4 4 4
Rack Mount Screw 4 4 4
Self Adhesive Label 2 2 2
OPTIONAL PART NUMBERS
Description Part Number
Universal Opt-X®Clamp Kit for Enclosure Mounting 5RCMP-KIT
Universal Opt-X®Clamp Kit for Rack Mounting 5RCMR-KIT
Fiber Cable Management 1/4 Ring Kit (bag of four 1/4 rings) 5R100-14R
Opt-X®500i Patch Cord Management Tray, 1RU 5R1UL-CMT
Opt-X®500i Patch Cord Management Tray, 2/3RU 5R2UL-CMT
Splice Tray Mounting Hardware Kit SPLMT-HKT
COVER REMOVAL / INSTALLATION
To remove cover: pull locking pins to unlock, and then slide cover to the rear. To install cover: assure locking pins
are unlocked , then slide cover onto the enclosure and push locking pin to latch cover in place.
Locking Pins
Locking Pins

Opt-X®500i LABELING
UNIVERSAL LABELING DEVICES
1RU – horizontal orientation 2RU – horizontal orientation 3RU – vertical orientation
•Use3/8”or3/4"labeltape, •Use3/8”or3/4"labeltape, •Use3/8”or3/4"labeltape,
depending on adapter plate depending on adapter plate depending on adapter plate
•Totallabellength=4"  •Totallabellength=4" •Totallabellength=23/4"
•Panelsectionis3/4"Hx4"L •Panelsectionis3/4"Hx4"L•Panelsectionis3/4"Wx23/4"H
Label Printing Organization by Fiber Adapter Type - 1 and
2 RU
Adapter No. of Ports Number Scheme
Duplex SC
(3 pack) 6 1 2 3 4 5 6
Duplex SC
(6 pack) 12
3-4 7-8 11-12
1-2 5-6 9-10
Duplex LC
(6 pack) 12
2 4 6 8 10 12
1 3 5 7 9 11
Quad LC
(6 pack) 24
5-6 / 7-8 13-14 / 15-16 21-22 / 23-24
1-2 / 3-4 9-10 / 11-12 17-18 / 19-20
ST/FC (6 pack) 6 1 2 3 4 5 6
ST/FC (8 pack) 8 1 - 2 - 3 - 4 - 5 - 6 - 7 - 8
Label Printing Organization by Fiber Adapter Type - 3 RU
Adapter Duplex SC
(3 pack)
Duplex SC
(6 pack)
Duplex LC
(6 pack)
Quad LC
(6 pack)
ST/FC
(6 pack)
ST/FC
(8 pack)
No. of
Ports 6 12 12 24 6 8
Number Scheme
1
1-2 3-4
1-2
1-2
3-4
5-6
7-8
11
2
3
4
5
6
7
8
2 3-4 2
3
5-6 7-8
5-6
9-10
11-12
13-14
15-16
3
4 7-8 4
5
9-10 11-12
9-10 17-18
19-20
21-22
23-24
5
6 11-12 6
Page 4 of 6
PK-93776-10-02-0B
5R1UL-F03
5R2UL-F06 5R3UL-F12

Page 5 of 6 PK-93776-10-02-0B
Opt-X®500i FIBER RING (Removal, Installation and Assembly)
Opt-X®Fiber management ¼ rings are pre-installed at the factory. To remove, grip the ¼ ring, lift the Position-
Locking Tab, turn counter clockwise until unlocked, and then lift to remove. When removing a half or full
management ring group, simultaneously lift the 2 or 4 Position-Locking Tabs, turn counter clockwise until unlocked,
and then lift to remove.
RING STACKING
Position initial ring unit (¼, ½, or full) upside
downonaatsurface.Positionadditional
ring upside down above initial ring and
presstogetherusingsufcientforceto
engage stack locking device.
CAUTION – always perform stacking
before installing ring unit into tray.
HALF RING ASSEMBLY
Hold a ¼ ring unit in each hand, bring the units
together and engage by placing the tab of the left
unit into the slot of the right unit.
HALF RING INSTALLATION Position ½ ring unit
overouterringslotssothealignmenttabstinto
slots. Press down and turn the ½ ring unit clock-
wise to engage tabs and lock into position.
CAUTION – when installing into a tray that is in the
enclosure, provide adequate support under the tray
by placing a hand under the ring slot area.
FULL RING ASSEMBLY
Hold a ½ ring unit in each hand, bring units together
with tabs above slots, rotate to engage tabs.
FULL RING INSTALLATION Position full ring unit
overinnerandouterringslotssoalignmenttabst
into slots. Firmly press down and turn the full ring
unit clockwise to engage tabs and lock into position.
CAUTION – when installing into a tray that is in the
enclosure, provide adequate support under the tray
by placing a hand under the ring slot area.
HALF RING ASSEMBLY FULL RING ASSEMBLY RING STACKING
Tab
Stacking/Locking
Device (Upper)
Stacking/Locking
Device (Lower)
Slot
RING OVERVIEW RING SIDE PROFILE RING ALIGNMENT SLOTS
Position-Locking Tab
Turn
Push

CABLE INSTALLATION - APPLICATIONS (Typicalinstallations-notspecictoenclosure)
Utilizing MTP® Cassettes
Utilizing Splice Trays Utilizing Fan-Out Kits
Utilizing Pre-Terminated Cables or Field
Termination of tight-buffered cable
Page 6 of 6
PK-93776-10-02-0B