Leviton VerifEye User manual

PK-A3236-10-00-0A
Series 8000 Meter
For use with catalog numbers: S8120, S8UWH & 277TS
Quick Start Guide
VerifEye™
WEB VERSION

WEB VERSION

1
TABLE OF CONTENTS
Warnings and Cautions .......................................................................................................... 2
Important Notes ..................................................................................................................... 2
Section 1: Full system overview ........................................................................................... 3
General Wiring Diagram: ....................................................................................................... 3
Section 2: Voltage and Meter Power Wiring Reference ...................................................... 4
Section 3: Wiring Diagrams ................................................................................................... 5
Split Phase 120/240 VAC (1P 3W) ........................................................................................ 5
3-Phase Wye 120/208 VAC (3P 4W) ..................................................................................... 5
1-Phase 120 VAC (1P 2W) .................................................................................................... 5
1-Phase Wye 277 VAC (1P 2W) ............................................................................................ 5
3-Phase Wye 277/480 VAC (3P 4W) ..................................................................................... 5
Section 4: Installing Current Transformers to Monitor the Loads ..................................... 6
Section 5: Installing the CT Wire Harness & Connecting CT Secondary Wires ............... 7
CT Amperage Ratings and Tenant Information Chart ............................................................ 8
WEB VERSION

2
• Please refer to the product manual or call/E-mail the Leviton®Meter Support Team for further
assistance (800-959-6004 / [email protected]).
• For the full listing of tools and equipment required for the complete installation of this
product, please refer to the manual for details.
• 347/600 V and 480 V delta services require external PTs to step down the voltages before
being wired to the meter.
IMPORTANT NOTES
HAZARD OF ELECTRICAL SHOCK, EXPLOSION, OR ARC FLASH
• TO AVOID DEATH, PERSONAL INJURY OR PROPERTY DAMAGE, disconnect service
voltage from the panel and use caution when working around energized circuits.
• Ensure the installation is completed per NEC®guidelines as well as local codes.
• A disconnect must be provided (such as a breaker from the panel) that will allow shut off of
power to the meter for servicing.
• Voltage references to the meter should be connected to a circuit breaker in the panel and/or
with appropriate fusing based on the NEC®and any local codes that are applicable.
• Apply appropriate personal protective equipment (PPF) and follow safe electrical work
practices. See NFPA 70E.
• This equipment must only be installed and serviced by qualified electrical personnel.
• Always use a properly rated voltage sensing device to confirm power is off.
• Replace all devices, doors and covers before turning on power to this equipment.
• The meters must be connected to the sense voltage and control voltage through a properly
rated voltage disconnect (not shown in the wiring diagrams).
Failure to follow these instructions will result in death or serious injury.
WARNINGS AND CAUTIONS
WEB VERSION

3
General Wiring Diagram:
WARNING: Ensure the installation is completed per NEC®guidelines as well as local codes. A disconnect must
be provided (such as a breaker from the panel) that will allow shut off of power to the meter for servicing.
The system diagram is intended to show the various electrical connections required for the Leviton Series 8000
multi-circuit meter. Indicated in the diagram are the names of the specific components of the meter which will be
referred to later in this guide. Follow the installation steps below for the appropriate wiring information depending on
the product model and panel service type.
SECTION 1: FULL SYSTEM OVERVIEW
CNA
ANBC
TO LOAD
TO LOAD
TO LOAD
TO LOAD
REFERENCE VOLTAGE
CT WIRING
HARNESS
BLACK
BLACK
BLACK
BLUE
BROWN
RED
BLACK
BLACK
BLACK
WHITE
BLACK
WHITE
WHITE
WHITE
WHITE
GREEN
S8000 METER
BREAKER PANEL
FROMSOURCE
CT
B
WEB VERSION

4
WARNING: Voltage references to the meter should be connected to a circuit breaker in the panel and/or with
appropriate fusing based on the NEC®and any local codes that are applicable.
NOTE: 347/600 V and 480 V delta services require external PTs to step down the voltages before being wired to
the meter.
Utilize the correct column below for the type of service being monitored. If none of the examples below match the
form of service in the panel, please refer to the full manual for additional types.
Now use the appropriate diagram on the following page for attaching the voltage references depending on the
panel feed.
For 120/208/240 VAC services
Verify that the meter has the appropriately installed
terminal block in place shown here:
A transformer is included with the meter for
powering the device. Make sure the connections
from the secondary side of the transformer and the
plug J2 below are made correctly:
For 277/480 VAC wye services
SECTION 2: VOLTAGE AND METER POWER WIRING REFERENCE
AUXN
Red
Blue N
A
AUXA
J2
White
Black Brown
White
AUXN
N
A
AUXA
J2
Yellow
Orange
WEB VERSION

5
SECTION 3: WIRING DIAGRAMS
1-Phase 120 VAC (1P 2W) 1-Phase Wye 277 VAC (1P 2W)
3-Phase Wye 277/480 VAC (3P 4W)
Split Phase 120/240 VAC (1P 3W)
3-Phase Wye 120/208 VAC (3P 4W)
J3
J18
AUXNAUXA
White
Black
C
B
A
N
J3
J18
AUXNAUXA
C
B
A
N
Brown
White
AN
Red
Black
White
J3
J18
AUXNAUXA
C
B
A
N
Red
Black
White
Blue
J3
J18
AUXNAUXA
C
B
A
N
Yellow
Orange
Brown
White
J3
J18
AUXNAUXA
C
B
A
AN
N
WEB VERSION

6
TO LOAD
TO LOAD
TO LOAD
LOAD
LINE
LOAD
LINE
LOAD
LINE
Correct installation of CT orientation on conductor from panel to load. This is an example of a three-phase installation.
Example of a split core CT.
Orientation is based on the product label indicating which
side should face the source.
Example of a solid core CT.
Orientation is based on the product label indicating which
side should face the source.
Use the appropriate diagram below to identify the correct orientation of the CT to the conductor. The “source”
refers to the side facing incoming power from the utility.
SECTION 4: INSTALLING CURRENT TRANSFORMERS TO MONITOR THE LOADS
SOURCE LOAD
Label To Source
500V 50/60Hz 0
Output: 0.1A
Sentran C
SOURCE LOAD
LOAD
LINE
WEB VERSION

7
TO LOAD
TO LOAD
TO LOAD
BLACK
BLACK
BLACK
RED
BLACK
BLACK
BLACK
WHITE
WHITE
WHITE
WHITE
GREEN
SECTION 5: INSTALLING THE CT WIRE HARNESS & CONNECTING CT SECONDARY WIRES
Install the wire harness AMP®connector to the board.
Wire harness AMP®plug inserted into socket
Example of a three phase (element) installation with the first three loads wired in the correct order
based on the cross-reference list above. The CT wires are always white (X1) and black (X2), and must be
appropriately associated with the correct colored pair from the harness.
Depending on the Series 8000 model purchased, the harness has a varying number of twisted pairs that are to be
matched with the corresponding CTs from the panel. Please refer to the spreadsheet on the last page of the quick
start guide which cross lists the twisted-pair wiring colors to the input number of the meter. Make sure to correctly
associate each twisted pair wire to the correct CT in the electrical panel.
Important! Fill out the spreadsheet with the appropriate CT amperage ratings and tenant information (circuit/apt/unit #)
associated with each of the CTs. This is provided on the last page of the quick start guide.
Once the tenant spreadsheet has been filled out and completed, the last steps are to configure the meter through
software and verify the hardware installation is correct. The manual includes the necessary information to complete the
commissioning of the Leviton Series 8000 multi-circuit meter.
WEB VERSION

8
CT AMPERAGE RATINGS AND TENANT INFORMATION CHART
S8000
Model
Number
1
Element
(CT)
Meter
Mode
2
Element
(CT)
Meter
Mode
3
Element
(CT)
Meter
Mode
Connect
X1 CT
lead
(white)
to X1
input
color
Connect
X2 CT
lead
(black)
to X2
input
color
CT
Amperage
Circuit
Number
Description
(Dwelling/Apt/Unit #)
Cable 1
P1-1 P1-1 P1-1 1Black Green P2-1 P1-2 P1-2 2Black White P3-1 P2-1 P1-3 3Black Red P4-1 P2-2 P2-1 4 Red Green P5-1 P3-1 P2-2 5 Red White P6-1 P3-2 P2-3 6Black Orange P7-1 P4-1 P3-1 7Black Brown P8-1 P4-2 P3-2 8Black Yellow P9-1 P5-1 P3-3 9Black Blue
P10-1 P5-2 P4-1 10 Green Yellow
P11-1 P6-1 P4-2 11 Green Blue
P12-1 P6-2 P4-3 12 Green White P13-1 P7-1 P5-1 13 Blue White P14-1 P7-2 P5-2 14 Green Orange P15-1 P8-1 P5-3 15 Green Brown P16-1 P8-2 P6-1 16 Blue Yellow P17-1 P9-1 P6-2 17 Brown White P18-1 P9-2 P6-3 18 Orange White P19-1 P10-1 P7-1 19 Red Orange P20-1 P10-2 P7-2 20 Red Yellow P21-1 P11-1 P7-3 21 Red Brown P22-1 P11-2 P8-1 22 Blue Orange P23-1 P12-1 P8-2 23 Yellow White P24-1 P12-2 P8-3 24 Blue Brown
8124 - S8120-122, S8UWH-083, S8UWH-122, S8UWH-241
8118 - S8120-092
8112 - S8120-062
8106 - S8120-032
Termination
Module CT #
WEB VERSION