LG LW1213ER User manual

AIR CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
P/NO:MFL67781905
www.LG.com
MFL67781905
MODEL，MODÈLE:LW1213ER
FRANÇAIS
OWNER’S MANUAL
GUIDE D’UTILISATION
S'il vous plaît lisez attentivement ce manuel avant d'utiliser
votre appareil et le conserver pour référence future.
CLIMATISEUR DE PIÈCE

23
12

Do not operate the air conditioner if
you smell gas.
Do not operate the air conditioner if
you smell gas.
For inner cleaning, contact an Authorized Service Center or a dealer.
Do not use harsh detergent that causes corrosion or damage on the unit.
Harsh detergent may also cause failure of product, fire, or electronic shock.

13
15
11
14
12
10
9
7
1. CABINET
2. FRONT GRILLE
3. AIR FILTER
4. AIR INTAKE (INLET GRILLE)
5. AIR DISCHARGE
6. VERTICAL AIR DEFLECTOR
(HORIZONTAL LOUVER)
7. EVAPORATOR
8. HORIZONTAL AIR DEFLECTOR
(VERTICAL LOUVER)
9. CONTROL PANEL
10. POWER CORD
11. COMPRESSOR
12. BASE PAN
13. BRACE
14. CONDENSER
15. REMOTE CONTROLLER(OPTIONAL)
4
6
5
8
1
2
3

Use of adapter plugs not pemitted in Canada.

5
4
3
2
1
About
Awning
Cooled air
Fence
Over 508mm
Heat
radiation
How to Install the Unit
To prevent vibration and noise, make sure the unit
is installed securely and firmly.
Install the unit where the sunlight does not shine
directly on the unit.
The outside of the cabinet must extend outward for
at least 305mm and there should be no obstacles,
such as a fence or wall, within 508mm from the back
of the cabinet because it will prevent heat radiation of the
condenser.
Restriction of outside air will greatly reduce the
cooling efficiency of the air conditioner.
CAUTION: All side louvers of the cabinet must remain exposed to the outside of the
structure.
Install the unit a little slanted so the back is slightly lower than the front (about 12.7mm).
This will force condensed water to flow to the outside.
Install the unit with the bottom about 762mm ~ 1524mm above the floor level.
~
mm267 mm4251
12.7mm
Window Requirements
: All supporting parts should be secured to firm wood, masonry, or metal.
• This unit is designed for installation in standard double
hung windows with actual opening widths from 686mm
to 991mm.
• The top and bottom window sash must open sufficiently
to allow a clear vertical opening of 406mm from the bottom
of the upper sash to the window stool.
NOTICE
686mm to 991mm
Offset
Sill
Exterior
Interior wall
600mm
(Without frame curtain)
Stool
406mm
(With frame curtain)
12.7mm to 31.8mm
min
min
Hardware Installation

Installation Kits Contents
Suggested Tool Requirements
12 3 4
8 10
765
12
119
NO. NAME OF PARTS Q'TY
1 FRAME CURTAIN 2
2 SILL SUPPORT 2
3 BOLT 2
4 NUT 2
5 SCREW (TYPE A) 13
6 SCREW (TYPE B) 3
7 SCREW (TYPE C) 5
8 FOAM-STRIP 1
9 DRAIN PIPE 1
10 FOAM-PE 1
11 FRAME GUIDE 2
12 WINDOW LOCKING BRACKET 1
Shipping
Screws
5
10
(Type A)
11
11
5
PREPARATION OF CHASSIS
SCREWDRIVER(Philips and Flatead), RULER, KNIFE, HAMMER, PENCIL, LEVEL
Remove the screws which fasten the cabinet at both
sides and at the back.
Slide the unit from the cabinet by gripping the base pan
handle and pulling forward while bracing the cabinet.
Cut the window sash seal to the proper length.
Peel off the backing and attach the Foam-PE to the
underside of the window sash.
Insert the Frame Guides into the bottom of the
cabinet.
Insert the Frame Curtain into the Upper Guide and
Frame Guides .
Fasten the curtains to the unit with  Type
A screws .
6
5
4
3
2
1
Hardware Installation

Cabinet Installation
Open the window. Mark a line on center of the
window stool.
Carefully place the cabinet on the window stool and
align the center mark on the bottom front with the
center line marked in the window stool.
Pull the bottom window sash down behind the Upper
Guide until it meets.
: Do not pull the window sash down tightly that
the movement of Frame Curtain is restricted.
Loosely assemble the Sill Support using the parts
in Fig. 3.
Select the position that will place the Sill Support
near the outer most point on sill (See Fig. 4)
: Be careful when you install the cabinet
(Frame Guides are broken easily).
Attach the Sill Support to the cabinet track hole in
relation to the selected position using 2 Type A
screws in each support (See Fig. 4).
5
NOTICE
4
3
NOTICE
2
1
INDOOR OUTDOOR
Sill Support
2
Nut
4
Bolt
3
INDOOR OUTDOOR
Cabinet
t 12.7mmuobA
Frame Guide
11
Screw(Type A)
5
Upper Guide Window stool
Front Angle
Window Sash Upper guide
Frame Curtain
1
Foam-pe
Cabinet
Fig. 1
Fig. 2
Fig. 3
Fig. 4
10
ENGLISH
Hardware Installation

Sash track
Front Angle
tuobA
Screw(Type B)
6
Screw(Type B)
6
Sill Support
2
Sill Support
2
Foam-Strip
8
Fig. 5
Type C
7
Fig. 6
Screw(Type A)
Screw
(Type A)
Power cord Fig. 7
Fig. 8
The cabinet should be installed with a very slight tilt
(about 12.7 mm) downward toward the outside
(See Fig. 5).
Adjust the bolt and the nut of Sill Support for
balancing the cabinet.
Attach the cabinet to the window stool by driving
the screws (Type B: Length 16mm (5/8 inch)
and below.) through the front angle into window
stool.
Pull each Frame Curtain fully to each window
sash track, and repeat step 2.
Attach each Frame Curtain the window sash using
screws (Type C). (See Fig. 6)
CAUTION: Do not drill a hole in the bottom
pan. The unit is designed to operate with
approximately 12.7mm of water in bottom pan.
There is no need to add water if the pan is
dry.
Slide the unit into the cabinet. (See Fig. 7)
CAUTION: For security purpose, reinstall
screws (Type A) at cabinet's sides.
Cut the Foam-Strip to the proper length and insert
between the upper window sash and the lower
window sash. (See Fig. 8)
11
10
9
8
7
6
12.7mm
Hardware Installation

Attach the Window Locking Bracket with a Type
C screw . (See Fig. 9)
Attach the front grille to the cabinet by inserting the
tabs on the grille into the tabs on the front of the
cabinet. Push the grille in until it snaps into place.
(See Fig. 10)
Pull down the inlet grille and secure it with a Type
A screw through the front grille. (See Fig. 11)
Window installation of room air conditioner is
now completed. See ELECTRICAL DATA for
attaching power cord to electrical outlet.
15
14
13
12
Window locking
bracket
12
Fig. 9
Fig. 10
Fig. 11
ENGLISH
Hardware Installation

POWER
Operation starts when this button is pressed and stops when you
press the button again.
FAN SPEED SELECTOR
For increased power while cooling,select a higher fan speed.
3 steps:High
―Low―Med.
ON/OFF TIMER
The Timer can be set to start and stop the unit in hourly increments
（up to 24 hours
You will usually use shut-off time while you sleep.
For your sleeping comfort，once timer is set ，the temperature setting will
raise &after 30min and once again after another 30min.
OPERATION MODE SELECTOR
Energy Saver:
Approximately every 3 minutes the fan will turn on
and check the room air tedetermine of cooling is need.
The fan stops when the compressor stops cooling.
C
Temp
Fan Speed
Timer Mode
1
2
4
3
5

Select dry mode for dry operation.
Dry：dry model is used to remove humidity from the room without additional cooling.
Once the set temperature is reached，the compressor and circulation fan turns off.
Fan speed is pre-set and cannot be adjusted.
TEMPERATURE CONTROL
The thermostat monitors room temperature to maintain the desired temperature.
The thermostat can be set between
The unit takes an average of 30 minutes to adjust the room temperature by 1 C.
16 C~30 C.
REMOTE CONTROL SENSOR
CAUTION
The Remote Controller will not function properly if strong light strikes the sensor window
of the air conditioner or if there are obstacles between the Remote Controller and the air
conditioner.
y
one battery
the battery is
battery
battery

Adjusting horizontal air flow Adjusting vertical air flow
•Adjusting Horizontal Air Flow Direction
Adjusting the vertical louvers left and right will
change horizontal airflow.
•Adjusting Vertical Air Flow Direction
Adjusting the horizontal vane up and down will
change vertical airflow. The vane can be adjusted
by nudging the vane backward or forward.
Adjusting the Air Flow Direction
ENGLISH
Operating Instructions
Adjusting the Air Flow Direction
•Recommended orientation of louvers
Adjust louvers to face upwards when cooling to maximize cooling efficiency.
Airflow can be adjusted by changing the direction of the air conditioner's louvers. This can also increase the
cooling efficiency of the air conditioner.
VENTCLOSE OPEN
Vent Control
For maximum cooling efficiency, CLOSE the vent. This will allow internal air circulation.
OPEN the vent to discharge stale air.
18

below