LG LKAEH098 User manual

1
ENGLISH ESPAÑOL
ELECTRIC HEATERS
INSTALLATION INSTRUCTIONS
Models: LKAEH098, LKAEH188, LKAEH368, LKAEH368L
• Please read this instruction sheet completely before installing the product.
• Installation work must be performed in accordance with national wiring standards by authorized
personnel only.
P/No.: 3828A30038F

2
Table 1 Accessory Heaters Electrical Data
Ton
6.25/7.5RT
8.5/10/12.5RT
15/17.5RT
20/25RT
Heater
Model No.
Heater
KW Rating
Control
Stages
26.0/27.2
37.5/39.5
60.5/64.5
42.0/43.2
53.5/55.5
76.5/80.5
79.4/95.3
100.2/120.3
108.6/130.4
380-415/50/3
380-415/50/3
380-415/50/3
380-415/50/3
380-415/50/3
380-415/50/3
380-415/50/3
380-415/50/3
380-415/50/3
LKAEH098
LKAEH188
LKAEH368
LKAEH098
LKAEH188
LKAEH368
LKAEH188
LKAEH368
LKAEH368L
7.5/9.0
15.1/18.0
30.2/36.0
7.5/9.0
15.1/18.0
30.2/36.0
15.1/18.0
30.2/36.0
30.2/36.0
1
1
2
1
1
2
1
2
2
60/60
60/60
80/80
60/60
70/70
100/100
125/125
150/150
150/150
60/60
60/60
80/80
60/60
70/70
100/100
125/125
150/150
150/150
31.0/32.2
42.5/44.5
65.5/69.5
47.0/48.2
58.5/60.5
81.5/85.5
85.4/101.3
106.2/126.3
114.6/136.4
60/60
60/60
80/80
60/60
80/80
100/100
125/125
150/150
150/150
60/60
60/60
80/80
60/60
80/80
100/100
125/125
150/150
150/150
Heater
Rated Volts
Standard indoor fan motor
M.C.A M.C.AM.F.S M.F.SM.C.B M.C.B
Oversized indoor motor
Note: Heater KW ratings are at 380/415V for 380/415V unit.
M.C.A; Minimum Circuit Ampere
M.F.S; Maximum Fuse Size
M.C.B; Maximum Circuit Breaker
* HACR type Circuit Breaker per NEC.
Installation
1. Loosen the screw that secures heater
compartment access panel. Lift up, pull
towards you and slide it down to remove.
2. Remove four(4) screws from block off panel
to expose heater cavity and heaterʼs back
support bracket. Save screws for installing
heater later.(See Figure 2.)
Heater Access Panel
Compressor Access Panel
Figure 1
Figure 2
: Open and lock unit disconnect
switch before installing this accessory to prevent
injury or death due to electrical shock or contact
with moving parts.
WARNING
Support
Bracket
Block off panel
Heater Cavity

ENGLISH
3
Heater and Control Box Assembly
3. Insert heater into the opening hole of heater
control box.
4. Align holes and secure screws to the control
box as shown in Figure 3.
Single Bank Heater Installation
- LKAEH098, LKAEH188, LKAEH368L
5. Place the heater control assembly in the
heater cavity.
6. Secure the heater control assembly of
heater cavity using four(4) screws. (See
Figure 4.)
Important: Make sure the heater arm slides
into heaterʼs back support bracket.
Two Bank Heaters Installation
- LKAEH368
7. For two heaters installation, align holes and
secure screws to the control box as shown
in Figure 3.
8. Secure the heater control assembly on
heater cavity using four(4) screws.(See
Figure 5)
Important: Make sure the heaterʼs arm slides
into heaterʼs back support bracket.
Heater Control Box
Heater
Figure 3
Figure 4
Figure 5

9. Remove the nut, lock washer and flat
washer from heater terminal posts marked
L1, L2 and L3.
10. Connect wiring from control box panel to
the correct terminal post as shown on
heaterʼs wiring diagram.
Note: The correct sequence for replacing the
hardware on the heater terminal posts is: 1)
wire connector 2) flat washer 3) locking washer
4) nut. “DO NOT OVER TIGHTEN NUT ON
TERMINALS” use a nut driver only to tighten
connection.(See Figure 6.)
4
L3
L2
Figure 6
Control Wiring
11. Connect control wires(Brown) on terminal
block (and P.C.B) as shown on wiring
diagram attached on compressor access
panel.
Power Wiring
12. Then route wires down through the
opening in the top of control box. Connect
wires to high voltage terminal block. Refer
to wiring diagram supplied with heater.
13. Check to make certain the proper size
fuses are installed per the fuse table for
the exact heater being used.
14. Ground unit at the grounding lug
provided. Make sure all field wiring
complies with all applicable codes and
water tightness.(Figure 7)
15. Remove compressor panel, then remove
unitʼs control box cover. Connect high
voltage leads to bottom of compressor
contactor or terminal block.(See unitʼs
wiring diagram.) Replace control box
cover and access panel onto unit.
(Figure 7)
CAUTION: Use copper conductors only to
prevent equipment damage. Unit terminals
are not designed to accept any other wiring.
16. Replace control box cover using four(4)
screws.
17. Replace heater access panel.
CAUTION: Do not over tighten the nuts on the
heater terminals. if the nuts are over tightened
the ceramic insulators will break and heaters
must be replaced.
Maximum torque on nuts is 11 inch
pounds.
To Unit Control Box
Ground
Power Supply
Terminal Block
Figure 7