LG DU-42PX12XD User manual

PLASMA TV
SERVICE MANUAL
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
CHASSIS :AF-044A
MODEL : DU-42PX12XD
CANADA : http//biz.lgservice.com
USA : http//www.lgservice.com
: http//lgservice.com/techsup.html

- 2 -
SAFETY PRECAUTIONS
Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance
An lsolation Transformer should always be used during
the servicing of a receiver whose chassis is not isolated from
the AC power line. Use a transformer of adequate power rating
as this protects the technician from accidents resulting in
personal injury from electrical shocks.
It will also protect the receiver and it's components from being
damaged by accidental shorts of the circuitary that may be
inadvertently introduced during the service operation.
If any fuse (or Fusible Resistor) in this monitor is blown, replace
it with the same specified type.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts.
Leakage Current Cold Check(Antenna Cold Check)
With the instrument AC plug removed from AC source,
connect an electrical jumper across the two AC plug prongs.
Place the AC switch in the on positioin, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Leakage Current Hot Check (See below Figure)
Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
Reverse plug the AC cord into the AC outlet and repeat AC
voltage measurements for each esposed metallic part. Any
voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
In case any measurement is out of the limits sepcified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
Leakage Current Hot Check circuit
CANADA: LG Electronics Canada, Inc. 550 Matheson
Boulevard East Mississauga, Ontario L4Z 4G3
USA : LG Customer Interactive Center
P.O.Box 240007, 201 James Record Road Huntsville,
AL 35824
Digital TV Hotline [phone]
1.5 Kohm/10W
To Instrument's
exposed
METALLIC PARTS
Good Earth Ground
such as WATER PIPE,
CONDUIT etc.
AC Volt-meter
IMPORTANT SAFETY NOTICE
0.15uF

- 3 -
SPECIFICATIONS.................................................................4
DESCRIPTION OF CONTROLS...........................................5
ADJUSTMENT INSTRUCTIONS ..........................................8
BLOCK DIAGRAM...............................................................12
EXPLODED VIEW..........................................................14,16
EXPLODED VIEW PARTS LIST....................................15,17
REPLACEMENT PARTS LIST............................................18
SCHEMATIC DIAGRAM..........................................................
PRINTED CIRCUIT BOARDS.................................................
TABLE OF CONTENTS

- 4 -
•The specifications shown above may be changed without prior notice for quality improvement.
MODEL
AC100-240V ~ 50/60Hz
NTSC-M, ATSC
VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 125, CADTV 1 ~ 135. DTV 2 ~ 69
75 Ω
1024 x 768 (Dot)
16,770,000 (256 steps of each R, G and B)
32 ~ 104°F (0 ~ 40°C)
Less than 80%
6561 feet (2000m)
41 / 1210
27.5 / 701
11.6 / 295
79.8 / 36.2
Width (inches / mm)
Height (inches / mm)
Depth (inches / mm)
Weight (pounds / kg)
Power requirement
Television System
Program Coverage
External Antenna Impedance
Resolution
Color
Operating Temperature Range
Operating Humidity Range
Maximum Elevation
DU-42PX12XD
SPECIFICATIONS

- 5 -
Controls
Controls
TV/VIDEO MENU VOLCH
- This is a simplified representation of front panel.
Image shown may be somewhat different from your TV.
Front Panel Controls
Front Panel Controls
POWER Button
Remote Control Sensor VOLUME (FF,GG) Buttons
Power Standby Indicator
Illuminates red in standby mode,
Illuminates green when the TV is
turned on.
CHANNEL (EE, DD) Buttons
MENU Button
TV/VIDEO Button
DESCRIPTION OF CONTROLS

- 6 -
Connection Options
Connection Options
RS-VIDEOVIDEO
L / MONO
AUDIO
A/V 2
REMOTE
CONTROL
RS-232C INPUT
(CONTROL/SERVICE)
AC INPUT
AUDIO INPUT
COMPONENT 2
COMPONENT 1
RL
DIGITAL AUDIO
(OPTICAL)
DVI
INPUT
COMPONENT1
INPUT
OUTPUT
AUDIO INPUT
DVI INPUT
(PC/DTV INPUT)
RGB INPUT
(PC/DTV INPUT)
VIDEO INPUT
DVD
/DTV
INPUT
A/V
INPUT 1
AUDIO
R L
(MONO)
VIDEO
S-VIDEO
Antenna
Analog/DTV
Back Connection Panel
Back Connection Panel
Antenna Inputs
Connect cable or antenna signals to the
TV, either directly or through your cable
box.
DVI Input/Audio Input/RGB
Input
Connect the monitor output con-
nector from a PC to the appro-
priate input port.
Digital Audio (DVI: Digital Visual
Interface/Component1) Input/
Digital Audio Output
Connect digital audio from various types
of equipment. Note: In standby mode,
these ports will not work.
Audio/Video Input 1
Connect audio/video out-
put from an external
device to these jacks.
DVD/DTV Input (Component
1-2)
Connect a component
video/audio device to these
jacks.
Remote Control
Port
Connect your wired
remote control here.
S-Video Input
Connect S-Video out from an
S-VIDEO device to the S-
VIDEO input.
Power Cord Socket
This TV operates on an AC power. The voltage is indi-
cated on the Specifications page. Never attempt to oper-
ate the TV on DC power.
S-VIDEO Input
A connection available to provide better
picture quality than the video input.
VIDEO Input
Connects the video signal from a video
device.
AUDIO Input
Use to connect to hear stereo sound
from an external device.
RS-232C INPUT
(CONTROL/SERVICE) PORT
Connect to the RS-232C port
on a PC.
DESCRIPTION OF CONTROLS

- 7 -
-When using the remote control, aim it at the remote control sensor on the TV.
LIGHT
TV/VIDEO
MODE
COMP/RGB/DVI
MUTE SURF
VOL CH
INFO
SAP RATIO
CC
MENU
SOUND VIDEO
EXIT
PLAY PAUSE STOP RECORD
PIP PIPCH- PIPCH+ PIPINPUT
FREEZE
ADJUST
OK
ZOOM SIGNAL SWAP
REW FF SKIP
POWER
TIMER
FLASHBK
LIGHT
Illuminates the remote control buttons.
TV/VIDEO
Selects: DTV, Analog, Video1-2,
Component 1-2, RGB-DTV (or RGB-PC),
DVI-DTV (or DVI-PC) input sources.
COMP/RGB/DVI
Selects: Component 1-2, RGB-DTV (or RGB-
PC), DVI-DTV (or DVI-PC) input sources.
NUMBER buttons
DASH
Used to enter a program number for multiple
program channels such as 2-1,2-2,etc.
MUTE
Switches the sound on or off.
VCR/DVD BUTTONS
Control some video cassette recorders or
DVD player ("RECORD" button is not avail-
able for DVD player).
RATIO
Changes the aspect ratio.
MODE
Selects the remote operating mode: TV,
VCR, DVD, CABLE, HDSTB or AUDIO.
Select other operating modes, for the
remote to operate external devices.
POWER
Turns your TV or any other programmed
equipment on or off, depending on mode.
TIMER
Lets you select the amount of time before
your TV turns itself off automatically.
SURF
Use to scroll the Surf channel list.
CC
Select a closed caption:
Off, EZ Mute, and On.
FLASHBK
Tunes to the last channel viewed.
THUMBSTICK (Up/Down/Left/Right/OK)
Allows you to navigate the on-screen
menus and adjust the system settings to
your preference.
CHANNEL UP/DOWN
Selects available channels found
with EZ scan.
EXIT
Clears all on-screen displays and returns to
TV viewing from any menu.
VIDEO
Adjusts the factory preset picture according
to the room.
VOLUME UP/DOWN
Increases/decreases the sound level.
SAP
Selects MTS sound: Mono, Stereo, and SAP.
Change the audio language in DTV mode.
MENU
Brings up the main menu to the screen.
INFO
When you watch the TV, displays information
on top of the screen. Not available in
Component 1-2, RGB and DVI mode.
SOUND
Selects the sound appropriate
for the program's character. PIP
Switches between PIP, POP (Picture-out-of-
Picture) and Twin picture modes.
PIPCH-/PIPCH+
Changes to next higher/lower PIP channel.
PIP INPUT
Selects the input source for the sub picture.
SWAP
Exchanges the PIP/main images.
FREEZE
Freezes the currently-viewed picture. Main
picture is frozen in PIP/Twin picturre mode.
ADJUST
Adjusts screen position, clock, and
phase in PC mode.
ZOOM
Enlarges the main picture size.
SIGNAL
Displays the digital signal strength.
Remote Control Key Functions
Remote Control Key Functions
DESCRIPTION OF CONTROLS

- 8 -
ADJUSTMENT INSTRUCTIONS
1. Application Object
These instructions are applied to all of the PDP TV, AF-044A.
2. Notes
(1) Because this is not a hot chassis, it is not necessary to use
an isolation transformer. However, the use of isolation
transformer will help protect test instrument.
(2) Adjustments must be done in the correct order.
(3) The adjustments must be performed in the circumstance of
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation.
(4) The input voltage of the receiver be must kept 100~240V,
50/60Hz when adjusting.
(5) The receiver must be operational for about 15 minutes
prior to the adjustments.
1) After receiving 100% white pattern, the receiver must be
operated prior to adjustment. (Or 7. White Pattern
condition in EZ - Adjust)
2) Enter into White Pattern
- Enter the Ez - Adjust by pressing ADJ Key on Service
Remote Control (S R/C).
- Select the 7. White Pattern using CH +/- Key and
press the Enter(Y) Key.
Display the 100% Full White Pattern.
[Set is activated HEAT-RUN without signal generator in
this mode.
If you turn on a still screen more than 20 minutes (Especially
Digital pattern(13 CH), Cross Hatch Pattern), an afterimage
may occur in the black level part of the screen.
3. EPLD Download
(1) Test Equipment: PC, Jig for download
(2) Connect the power of VSC B/D.
(3) Execute download program(Flash Loader) of PC.
(4) After executing execution hot key (Programmer), icon click
(5) End after confirming
Each PCB Assy must be checked by Check JIG Set before
assembly. (Especially, be careful Power PCB Assy which can
cause fatal Damage to PDP Module.)
4. POWER PCB Assy Voltage
Adjustment (Va, Vs Voltage Adjustment)
4-1 Test Equipment :D.M.M 1EA
4-2 Connection Diagram for Measuring
Refer to Fig 2.
PC VSC
B/D
<Fig 1> Connection Diagram of EPLD Download
<Fig 2-1> Connection Diagram of Power Adjustment for
Measuring (Power Board): 42PY10 Series
<Fig 2-2> Connection Diagram of Power Adjustment for
Measuring (Power Board): 50PY10 Series

- 9 -
ADJUSTMENT INSTRUCTIONS
4-3 Adjustment Method(42/50PY10)
(1) Va Adjustment
1) Connect + terminal of D.M.M to Va pin of P805 and
connect – terminal to GND pin of P805.
2) Adjust VR351 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)
(2) Vs adjustment
1) Connect + terminal of D.M.M to Vs pin of P805 and
connect – terminal to GND pin of P805.
2) Adjust VR551 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)
4-4 Adjustment Method(60PY10)
(1) PFC Adjustment
1) After receiving 100% White Pattern, HEAT RUN.
2) Connect + terminal of DMM to PFC + terminal of
P803A,connect - terminal of DMM to GND of P803A.
3) Adjust VR801 until voltage reading is 380V(±1V).
(2) Va Adjustment
1) Connect + terminal of D.M.M to Va pin of P8011 and
connect – terminal to GND pin of P8011.
2) Adjust VR8401 voltage to match that of the label on the
Top/Right of the panel.(Deviation : ±0.5V)
(3) Vs adjustment
1) Connect + terminal of D.M.M to Vs pin of P8011 and
connect – terminal to GND pin of P8011.
2) Adjust VR8501 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)
5. EDID(The Extended Display
Identification Data)/DDC
(Display Data Channel) download
This is the function that enables “Plug and Play".
(1) EDID DATA(42PY10)
:EDID for DVI (DDC (Display Data Channel) Data)
EDID table =
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
_________________________________________________________
00 | 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 | 06 0D 01 03 98 5C 34 96 08 CF 72 A3 57 4C B0 23
20 | 09 45 5D EF CE 00 31 D9 31 59 45 59 01 01 01 01
30 | 01 01 01 01 01 40 C3 1E 00 20 41 00 20 30 10 60
40 | 13 00 98 08 32 00 00 18 00 00 00 FC 00 4C 47 20
50 | 50 44 50 20 44 4E 2F 44 55 0A 00 00 00 FD 00 30
60 | 4C 1E 64 0F 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 2D 34 32 50 59 31 30 20 20 20 20 20 0A 00 2E
:EDID DATA for RGB
EDID table =
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
__________________________________________________________
00 | 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 | 06 0D 01 03 18 5C 34 96 08 CF 72 A3 57 4C B0 23
20 | 09 45 5D EF CE 00 31 D9 31 59 45 59 01 01 01 01
30 | 01 01 01 01 01 40 C3 1E 00 20 41 00 20 30 10 60
40 | 13 00 98 08 32 00 00 18 00 00 00 FC 00 4C 47 20
50 | 50 44 50 20 44 4E 2F 44 55 0A 00 00 00 FD 00 30
60 | 4C 1E 64 0F 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 2D 34 32 50 59 31 30 20 20 20 20 20 0A 00 AE
<Fig 2-3> Connection Diagram of Power Adjustment for
Measuring (PFC Board): 60PY10 Series
<Fig 2-4> Connection Diagram of Power Adjustment for
Measuring (Power Board): 60PY10 Series

- 10 -
ADJUSTMENT INSTRUCTIONS
(2) EDID DATA(50PY10)
:EDID for DVI (DDC (Display Data Channel) Data)
EDID table =
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
__________________________________________________________
00 | 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 | 03 0D 01 03 98 6E 3E 96 08 CF 72 A3 57 4C B0 23
20 | 09 45 5D EF CE 00 31 D9 31 59 45 59 01 01 01 01
30 | 01 01 01 01 01 40 C3 1E 00 20 41 00 20 30 10 60
40 | 13 00 4C 6C 42 00 00 1E 00 00 00 FC 00 4C 47 20
50 | 50 44 50 20 44 4E 2F 44 55 0A 00 00 00 FD 00 30
60 | 4C 1E 64 0F 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 2D 35 30 50 59 31 30 20 20 20 20 20 0A 00 E8
:EDID DATA for RGB
EDID table =
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
__________________________________________________________
00 | 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 | 03 0D 01 03 08 6E 3E 96 08 CF 72 A3 57 4C B0 23
20 | 09 45 5D EF CE 00 31 D9 31 59 45 59 01 01 01 01
30 | 01 01 01 01 01 40 C3 1E 00 20 41 00 20 30 10 60
40 | 13 00 4C 6C 42 00 00 18 00 00 00 FC 00 4C 47 20
50 | 50 44 50 20 44 4E 2F 44 55 0A 00 00 00 FD 00 30
60 | 4C 1E 64 0F 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 2D 35 30 50 59 31 30 20 20 20 20 20 0A 00 7E
(3) EDID DATA(60PY10)
:EDID for DVI (DDC (Display Data Channel) Data)
EDID table =
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
__________________________________________________________
00 | 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 | 03 0D 01 03 98 6E 3E 96 08 CF 72 A3 57 4C B0 23
20 | 09 45 5D EF CE 00 31 D9 31 59 45 59 01 01 01 01
30 | 01 01 01 01 01 40 C3 1E 00 20 41 00 20 30 10 60
40 | 13 00 4C 6C 42 00 00 1E 00 00 00 FC 00 4C 47 20
50 | 50 44 50 20 44 4E 2F 44 55 0A 00 00 00 FD 00 30
60 | 4C 1E 64 0F 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 2D 36 30 50 59 31 30 20 20 20 20 20 0A 00 E7
:EDID DATA for RGB
EDID table =
0 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
__________________________________________________________
00 | 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 | 03 0D 01 03 08 6E 3E 96 08 CF 72 A3 57 4C B0 23
20 | 09 45 5D EF CE 00 31 D9 31 59 45 59 01 01 01 01
30 | 01 01 01 01 01 40 C3 1E 00 20 41 00 20 30 10 60
40 | 13 00 4C 6C 42 00 00 18 00 00 00 FC 00 4C 47 20
50 | 50 44 50 20 44 4E 2F 44 55 0A 00 00 00 FD 00 30
60 | 4C 1E 64 0F 00 0A 20 20 20 20 20 20 00 00 00 FC
70 | 00 2D 36 30 50 59 31 30 20 20 20 20 20 0A 00 7D
6. AD9883A-Set Adjustment
6-1 Synopsis
AD9883A-Set adjustment to set the black level and the Gain
of optimum with an automatic movement from the analog =>
digital converter and RGB revises a deviation a function for it
is.
6-2 Test Equipment
Service R/C, 801GF(802B, 802F, 802R) Pattern Generator
(720P The Vertical 100% Color Bar Pattern output will be
possible and the output level will accurately have to be
revised with 0.7±0.1Vp-p)
6-3 Adjustment
(1) Select Component1 or Component2 as the input with
100% Vertical Color Bar Pattern in 720p Mode.
(2) After receiving signal for at least 1 second, press the ADJ
Key on the Service R/C to enter the ‘Ez - Adjust’ and select
the ‘1. AD9883A-Set’.
Pressing the + Key to adjust with automatic movement.
(3) When the adjustment is over in the normality and the
message which is a ‘AD9883 - Set’ becomes the display
and the case which has not become the normality the
message which is a ‘AD9883A set error’ becomes the
display.
(4) Readjust after confirming the case Pattern or adjustment
condition where the adjustment had not become the
normality.
(5) After adjustment is complete, exit the adjustment mode by
pressing the ADJ KEY.
<Fig 3> Adjustment Pattern : 720P Vertical Color Bar

- 11 -
ADJUSTMENT INSTRUCTIONS
7. Adjustment of White Balance
7-1. Required Equipment
(1) Color analyzer (CA-100 or similar product)
(2) Automatic adjustor (with automatic adjustment hour
necessity and the RS-232C communication being possible)
(3) AV Pattern Generator
7-2. Connection Diagram of Equipment for
Measuring (Automatic Adjustment)
7-3. Adjustment of White Balance
O Operate the Zero-calibration of the CA-100, then attach
sensor to PDP module surface when you adjust.
O Manual adjustment is also possible by the following sequence.
(1) Enter ‘Ez - Adjust’ by pressing ADJ KEY on the Service
Remote Control.
(2) Select "7. WHITE PATTERN" using CH +/- Key and HEAT
RUN at least 15 minutes by pressing the ENTER Key.
(3) Receive the Window pattern signal from AV Pattern
Generator. (AV Input)
(4) Set Picture condition to “CLEAR Image” and ‘XD’ off
(5) After attaching sensor to center of screen, select ‘3. White-
Balance’ of ‘Ez - Adjust’ by pressing the ADJ KEY on the
Service R/C. Then enter adjustment mode by pressing the
Right KEY (
G ) .
(6) Adjust the Hight Light using R Gain/B Gain and adjust the
Low Light using G Cut/B Cut.
(7) Adjust using Volume +/- KEY.
(G Gain : 123 / R Cut : 63(Fix.))
Hight Light : 150±10 Cd
Low Light : 5±2 Cd
X; 0.285±0.003
Y; 0.285±0.003
Color temperature: 9,000°K±500°K
(8) After adjustment is complete, move to Ez - Adjust screen by
pressing the ENTER(Y) KEY. Then exit the adjustment mode
by press ADJ KEY.
7-4. Main/Sub Contrast Adjustment
Main/Sub contrast adjustment reduces the contrast difference
of Main/Sub screen in PIP/POP/SPLIT Screen.
(1) After receiving signal for at least 1 second, press the ADJ
KEY on the Service R/C and enter the ‘Ez - Adjust’ then
select ‘2. VPX3226’.
Enter adjustment mode by pressing the Right KEY(
G ).
(2) When entering adjustment mode, the image TV becomes
6CH SPLIT Screen with automatic movement as in below
window.
(3) The contour of “US 6CH” letter of left Main screen is most
clear and it is clear, 1.Contrast (Main) after adjusting first,
in order for right side Sub screen to contrast to become the
left Main screen to contrast with same, 2.Contrast (Sub) it
adjust. This time adjust using the volume +/- Key.
(4) After adjustment is complete, exit the adjustment mode by
press ADJ KEY.
7-5. DVCO Adjustment
(1) After adjusting Main/Sub Contrast, receive a Digital
Pattern.
(2) Select ‘4. DVCO-Set’ by pressing the ADJ KEY on the
Service R/C and adjust by pressing the Right KEY (
G ) .
(3) When adjustment is complete,“DVCO-Set“ will appear. Exit
the adjustment mode menu by pressing ADJ key.
High Light Adjustment
Low Light Adjustment
Signal Input
<Fig 4> Connection Diagram of Automatic Adjustment

- 12 -
BLOCK DIAGRAM

- 13 -
NOTES

- 14 -
EXPLODED VIEW(X2 Module)
300
301
304
302
303
410
402
520
560
530
531
570
120
601
600
305
121
101
103
200
580
204
207
201
205
206
202
203
590
490
102 101
400
430

- 15 -
EXPLODED VIEW PARTS LIST
101 5900V06008B FAN,DC G6015S12B2-RG DONGYANG 60*60*15 7V 1900RPM 6/12V L=500MM
102 4980V01135A SUPPORTER,FAN SECC(EGI) DN-42PX12X
103 4980V00D43B SUPPORTER,FAN SECC(EGI) MZ-42PM10 PRESS
120 6401VD0013P SPEAKER ASSEMBLY,FULL RANGE(L) 6401VD0013P RZ-42PX10 CI
121 6401VD0013N SPEAKER ASSEMBLY,FULL RANGE(R) 6401VD0013N RZ-42PX10 CIN
200 6348Q-E042D PDP,42 16:9 1024*768 PDP42X20000.AKLGG
6348Q-E084A PDP,42 1024*768 PDP42X20000.DDRSA C/SKD
201 6871QCH038A PCB ASSEMBLY,DISPLAY CTRL ASSY 42X2 CTRL LGDP4023,4013
202 6871QDH068A PCB ASSEMBLY,DISPLAY YDRV ASSY 42X2 YDRV TOP
203 6871QDH069A PCB ASSEMBLY,DISPLAY YDRV ASSY 42X2 YDRV BOTTOM
204 6871QLH037A PCB ASSEMBLY,DISPLAY XRLT ASSY 42X2 X-LEFT(TCP)
205 6871QRH043A PCB ASSEMBLY,DISPLAY XRRT ASSY 42X2 X-RIGHT (TCP)
206 6871QYH030A PCB ASSEMBLY,DISPLAY YSUS ASSY FOR 42X2
207 6871QZH034A PCB ASSEMBLY,DISPLAY ZSUS ASSY FOR 42X2
300 3091V00763G CABINET ASSEMBLY
3091V00763H CABINET ASSEMBLY,DU-42PX12XD NON AF044A PC-ABS LGEUS C/SKD
301 4980V01067J SUPPORTER ASSY,AL FILTER TOP DN-42PX12X 7T
4980V01067K SUPPORTER ASSY,AL FILTER TOP DU-42PX12XD C/SKD
302 4980V01068J SUPPORTER ASSY,AL FILTER BOT DN-42PX12X 7T
4980V01068K SUPPORTER ASSY,AL FILTER BOT DU-42PX12XD C/SKD
303 4980V01069J SUPPORTER ASSY,AL FILTER RIGHT DN-42PX12X 7T
4980V01069K SUPPORTER ASSY,AL FILTER RIGHT DU-42PX12XD C/SKD
304 4980V01070J SUPPORTER ASSY,AL FILTER LEFT DN-42PX12X 7T
4980V01070K SUPPORTER ASSY,AL FILTER LEFT DU-42PX12XD C/SKD
305 3790V00709C FILTER(MECH),LGM42-09 MITSUI 42 ETCHING MESH GLASS FILTER
400 3809V00610B BACK COVER ASSEMBLY
3809V00610D BACK COVER ASSEMBLY,DU-42PX12XD NON C/SKD WITH PEM-NUT
402 3301V00023S PLATE ASSEMBLY,AV VSC TUNER DU-42PX12XD LGEUS
410 4980V01056A SUPPORTER,MODULE AL RZ-42PY20 VERTICAL
430 3501V00171A BOARD ASSEMBLY,BASE RZ-42PY20 NON DESK TOP STAND
3501V00171B BOARD ASSEMBLY,STAND RZ-42PX10 NF036B SKD
490 4980V01057A SUPPORTER,PCB EGI POWER SW. RZ-42PY20
4980V01057B SUPPORTER,PCB EGI POWER SW RZ-42PX10 SKD
520 6871VMMJ89A PCB ASSEMBLY,MAIN AF044A DU-42PX12XD
530 6871VSMK93A PCB ASSEMBLY,SUB PSW AF044A DU-42PX12XD
68719SM990A PCB ASSEMBLY,SUB AF044A DU-42PX12XD SUSLLBR PSW MANUAL
531 5020V00915A BUTTON,POWER RZ-42PX20 ABS 1KEY NON
5020V00915B BUTTON,POWER RZ-42PX10 ABS, AF-303S NON SKD
560 6871VSMJ89A PCB ASSEMBLY,SUB TUNER AF044A DU-42PX12XD
570 6871VSMF17B PCB ASSEMBLY,SUB P/AMP AF044A DU-42PX10C CONTROL
6871VSMF17C PCB ASSEMBLY,SUB P/AMP AF044A DU-42PX12X/12XC CONTROL, SKD IN RS
580 3501V00181B POWER SUPPLY ASSEMBLY,POWER DN-42PY10X AF044A MURATA MPF7413
590 3141VSNB49C CHASSIS ASSEMBLY,SUB RF03FA LINE FILTER ASSY. 7 TURN TWIST
600 6871VSMF13A PCB ASSEMBLY,SUB A/V AF044A DN-50PY10 SIDE A/V
601 4811V00118B BRACKET ASSEMBLY,DECO RU-42PX10 RF043A SIDE AV
4811V00118D BRACKET ASSEMBLY,AV RT-42PX10 RF043B SIDE AV SKD
No. Part No. Description

- 16 -
EXPLODED VIEW(X2A Module)
300
301
304
302
303
400
401
430
410
402
520
560
530
531
570
120
601
600
305
121
590
490
205
206
207
200
101
103 201
202
203
204
580
102 101

- 17 -
EXPLODED VIEW PARTS LIST
101 5900V06008B FAN,G6015S12B2-RG DONGYANG 60*60*15 7V 1900RPM 6/12V L=500MM
102 4980V01135A SUPPORTER,FAN SECC(EGI) DN-42PX12X
103 4980V00D43B SUPPORTER,FAN SECC(EGI) MZ-42PM10 PRESS
120 6401VD0013P SPEAKER ASSEMBLY,FULL RANGE(L) 6401VD0013P RZ-42PX10 CI
121 6401VD0013N SPEAKER ASSEMBLY,FULL RANGE(R) 6401VD0013N RZ-42PX10 CI
200 6348Q-E120U PDP,42 1024*768 PDP42X20882
6348Q-E120N PDP,42 1024*768 PDP42X20882.AKLGG SET
201 6871QCH060Q PCB ASSEMBLY,DISPLAY CTRL ASSY 42HD 42X2A PB FREE AU
202 6871QYH051P PCB ASSEMBLY,DISPLAY YSUS ASSY 42HD 42X2A FOR PB FREE
203 6871QDH107P PCB ASSEMBLY,DISPLAY YDRV ASSY 42HD 42X2A YDRV TOP (FOR PB FREE)
204 6871QDH108P PCB ASSEMBLY,DISPLAY YDRV ASSY 42HD 42X2A YDB (FOR PB FREE)
205 6871QLH037R PCB ASSEMBLY,DISPLAY XRLT ASSY _ 42X2A X-LEFT(TCP) FOR PB FREE AU
206 6871QRH043S PCB ASSEMBLY,DISPLAY XRRT ASSY _42X2A X-RIGHT(TCP) FOR PB FREE AU
207 6871QZH054P PCB ASSEMBLY,DISPLAY ZSUS ASSY 42HD 42X2A FOR PB FREE
300 30919E0035E CABINET ASSEMBLY,DU-42PX12XD NO BRAND 2TONE LGERS LOCAL PH
3091V00763G CABINET ASSEMBLY,DU-42PX12XD NON AF044A PC-ABS LGEUS DCR
301 4980V01067K SUPPORTER ASSY,AL FILTER TOP DU-42PX12XD C/SKD
4980V01067J SUPPORTER ASSY,AL FILTER TOP DU-42PX12XD/20 6T
302 4980V01068K SUPPORTER ASSY,AL FILTER BOT DU-42PX12XD C/SKD
4980V01068J SUPPORTER ASSY,AL FILTER BOT DU-42PX12XD/20 6T
303 4980V01069K SUPPORTER ASSY,AL FILTER RIGHT DU-42PX12XD C/SKD
4980V01069J SUPPORTER ASSY,AL FILTER RIGHT DU-42PX12XD/20 6T
304 4980V01070K SUPPORTER ASSY,AL FILTER LEFT DU-42PX12XD C/SKD
4980V01070J SUPPORTER ASSY,AL FILTER LEFT DU-42PX12XD/20 6T
305 3790V00709C FILTER(MECH),LGM42-09 MITSUI 42 ETCHING MESH GLASS FILTER
400 3809V00610D BACK COVER ASSEMBLY,DU-42PX12XD NON C/SKD WITH PEM-NUT
3809V00610B BACK COVER ASSEMBLY,DU-42PX12XD NON LGEUS C-BOX WITH LABEL
402 3301V00023S PLATE ASSEMBLY,AV VSC TUNER DU-42PX12XD LGEUS
410 4980V01056A SUPPORTER,MODULE AL RZ-42PY20 VERTICAL
430 3501V00171B BOARD ASSEMBLY,STAND RZ-42PX10 NF036B SKD
3501V00171A BOARD ASSEMBLY,BASE RZ-42PY20 NON DESK TOP STAND
490 4980V01057B SUPPORTER,PCB EGI POWER SW RZ-42PX10 SKD
4980V01057A SUPPORTER,PCB EGI POWER SW. RZ-42PY20
520 6871VMMJ89A PCB ASSEMBLY,MAIN AF044A DU-42PX12XD
530 68719SM990A PCB ASSEMBLY,SUB AF044A DU-42PX12XD SUSLLBR PSW MANUAL
6871VSMK93A PCB ASSEMBLY,SUB PSW AF044A DU-42PX12XD
531 5020V00915B BUTTON,POWER RZ-42PX10 ABS, AF-303S NON SKD
5020V00915A BUTTON,POWER RZ-42PX20 ABS 1KEY NON
560 6871VSMJ89A PCB ASSEMBLY,SUB TUNER AF044A DU-42PX12XD
570 6871VSMF17C PCB ASSEMBLY,SUB P/AMP AF044A DU-42PX12X/12XC CONTROL, SKD IN RS
6871VSMF17B PCB ASSEMBLY,SUB P/AMP AF044A DU-42PX10C CONTROL
580 3501V00181B POWER SUPPLY ASSEMBLY,POWER DN-42PY10X AF044A MURATA MPF7413
590 31419SF072A CHASSIS ASSEMBLY,SUB AF044A DU-42PX12XD AC INET ASSY,SKD,RS
3141VSN932D CHASSIS ASSEMBLY,SUB AF044A AC INET ASSY X2
600 6871VSMF13A PCB ASSEMBLY,SUB A/V AF044A DN-50PY10 SIDE A/V
601 4811V00118D BRACKET ASSEMBLY,AV RT-42PX10 RF043B SIDE AV SKD
4811V00118B BRACKET ASSEMBLY,DECO RU-42PX10 RF043A SIDE AV
No. Part No. Description

- 18 -
REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION
IC604
IC605
IC606
IC607
IC608
IC609
IC701
IC702
IC703
IC704
IC705
IC706
IC707
IC800
IC801
IC900
IC901
IC902
Q100
Q101
Q101
Q102
Q102
Q103
Q103
Q104
Q104
Q105
Q106
Q107
Q108
Q109
Q110
Q111
Q112
Q113
Q114
Q115
Q116
Q117
Q118
Q119
Q120
Q121
Q122
Q123
0IMCRFA013A
0ICB841500B
0ITO741570C
0ITO741570C
0ICB533100A
0IMO330780B
0IPMGKE030A
0IPRPML001A
0IMCRSJ001A
0IMCRFA010A
0IPRPNS054A
0IPMGKE032A
0IPMGKE032A
0ICTMLG018A
0IPRPML001A
0IPRPAT002A
0IPMGSG018C
0IMMRAT006C
0TR150400BA
0TR102008AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR387500AA
0TR150400BA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
74LCX244MTC FAIRCHILD 20P
CS8415A-CZR 28P
TC74LCX157FT 16P
TC74LCX157FT 16P
CS5331A-KSR 8SOIC TP ADC -
MC33078D 8/SOIC +-18V OP AMP
KIA78R05F KEC 5PIN
MIC39100 MICREL 3P SOT223
SC1565IST-1.8 SEMTECH 3P SOT223
KA7809R, FAIRCHILD 2P
LM75CIMX-3 8P
KIA78R09F KEC 5PIN
KIA78R09F KEC 5PIN
LGDP4410 LG IC 176P
MIC39100 MICREL 3P SOT223
EP1C12F256C8N(PB FREE) 256P
LD1086DT15TR SGS-THOMSON 2P
EPCS4S18N(PROGRAMED) 8PIN
CHIP 2SA1504S(ASY) KEC
KRA102S SOT23 CHIP TR
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
LOCA. NO PART NO DESCRIPTION
IC100
IC101
IC101
IC103
IC104
IC107
IC108
IC109
IC110
IC111
IC112
IC114
IC200
IC201
IC201
IC202
IC202
IC203
IC203
IC204
IC204
IC205
IC205
IC206
IC206
IC209
IC210
IC301
IC303
IC304
IC305
IC306
IC308
IC310
IC400
IC401
IC402
IC403
IC404
IC501
IC502
IC503
IC600
IC601
IC602
IC603
0IMMRNE002A
0ISO206900A
0IKE702900G
0IMCRSS016A
0IPH741400E
0IMMRAL053A
0IMMRAL053A
0IMMRSS041D
0IMMRSS041D
0IKE704200J
0IMMR00037A
0IMCRAL006A
0IMCRMN027D
0IMCRNL001A
0IMCRPH026B
0ICTMLG013A
0IMCRTI028C
0IMCRCY002A
0IPMGKE030A
0IMCRSJ001A
0IAL242561B
0IMCRXL004A
0IPRPML001A
0IMCRSG010A
0IMCRFA010A
0IMCRRH001A
0IMCRPH026B
0ITK118100B
0IPMGKE030A
0ICTMLG019A
0ILNRMN005A
0ILNRMN005A
0IMCRAD002A
0IMCRRH001A
0ICTMLG009C
0IMMRSS041D
0IMMRSS041D
0IMMRSS041D
0IMMRSS041D
0IMCRS5003A
0IMCRTH002A
0IMMRAL014B
0IMCRSO008A
0IMO140530D
0IPH740800M
0IMMRAL014B
UPD64083GF3BA 100
CXA2069Q QFP64 BK I2C BUS AV S/W
KIA7029AF SOT-89 TP 2.9V
S3C44BOX01-EDRO LQFP-160 TRAY CPU
74HC14D 14SOP TP SHITTER TRIGGER
AT49BV320C-70TU 480
AT49BV320C-70TU 480
K4S641632H-TL75 54P
K4S641632H-TL75 54P
KIA7042AF SOT-89 TP 4.2V
M306H3FCFP 116P
AT24C16AN-10SI-2.7 8P
MSP4440K 80P
NSP-6241B 64P
PA9516APW 16P
LGDT1901A LG IC 24P
TAS5122DCAR 56P/TSSOP
CY2309SXC-1HT CYPRESS SOIC 16P
KIA78R05F KEC 5PIN
SC1565IST-1.8 3P SOT223
AT24C256W-10SI-2.7V 8P
XC95288XL-10TQG144C 144P
MIC39100 MICREL 3P SOT223
ST3232CDR SGS-THOMSON SOP16
KA7809R, FAIRCHILD 2P
BA033FP-E2 ROHM 3P-SOP,TO252-3
PA9516APW PHILIPS 16P
TK11840L 8P SOT23L
KIA78R05F KEC 5PIN
LGDT3303 LG IC 100P
VPX3226E MICRONAS 44
VPX3226E MICRONAS 44
AD9883AKST-110 80P
BA033FP-E2 ROHM 3P-SOP,TO252-3
LGDT1102C HD2.3 LG IC SBGA-432P
K4S641632H-TL75 54P
K4S641632H-TL75 54P
K4S641632H-TL75 54P
K4S641632H-TL75 54P
SIL169CT100 100P
THC63LVD103 64P
AT24C02N-10SI-2.7 8P
CXA2151Q SONY 48P
MC14053BDR2 16P
74F08D 14P
AT24C02N-10SI-2.7 8P
IC
TRANSISTOR
RUN DATE : 2005.3.16
For Capacitor & Resistors, the
charactors at 2nd and 3rd digit
in the P/No. means as follows;
CC, CX, CK, CN : Ceramic
CQ : Polyestor
CE : Electrolytic
RD : Carbon Film
RS : Metal Oxide Film
RN : Metal Film
RF : Fusible

- 19 -
LOCA. NO PART NO DESCRIPTION
Q124
Q125
Q128
Q129
Q130
Q131
Q132
Q133
Q200
Q200
Q201
Q201
Q202
Q204
Q301
Q301
Q302
Q303
Q303
Q304
Q304
Q305
Q306
Q307
Q308
Q309
Q501
Q502
Q503
Q505
Q506
Q507
Q600
Q601
Q602
Q605
Q606
Q607
Q613
Q614
Q615
Q616
Q701
D109
D200
D201
D202
D203
D204
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR150400BA
0TR150400BA
0TR150400BA
0TR150400BA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR830009BA
0TR830009BA
0TR387500AA
0TR150400BA
0TR150400BA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR150400BA
0TR387500AA
0TR387500AA
0TR387500AA
0TR387500AA
0TR102009AG
0TR387500AA
0DL233309AC
0DD226239AA
0DD226239AA
0DD226239AA
0DD226239AA
0DZRM00248A
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
BSS83
BSS83
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SA1504S(ASY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP 2SC3875S(ALY) KEC
CHIP KRC102S SOT-23 NA NA
CHIP 2SC3875S(ALY) KEC
LED,SAM2333
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
KDS226 TP KEC
ZENERS,RLZ8.2B-TE11
LOCA. NO PART NO DESCRIPTION
D302
D303
D501
D701
D702
DL700
DL702
DL703
DL704
DL705
IC102
LD201
ZD101
ZD102
ZD103
ZD110
C104
C105
C106
C117
C118
C1203
C121
C1213
C1216
C1219
C122
C1221
C1222
C1226
C1242
C1243
C1244
C1255
C1258
C127
C133
C138
C138
C138
C139
C139
C1400
C143
C144
C146
C148
C148
C149
0DD184009AA
0DD226239AA
0DD184009AA
0DD226239AA
0DD100009AM
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DL233309AC
0DD184009AA
0DL200000CA
0DR050008AA
0DR050008AA
0DR050008AA
0DR050008AA
0CE1059K538
0CE1059K538
0CE106SF6DC
0CE106SF6DC
0CE105SK6DC
0CE226SF6DC
0CE106SF6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE107SF6DC
0CK105DF64A
0CK105DF64A
0CE108DJ618
0CF4741L438
0CF4741L438
0CE476SF6DC
0CE108DJ618
0CE107SF6DC
0CE107SF6DC
0CE476SF6DC
0CE107SF6DC
0CE476SF6DC
0CE107SF6DC
0CE476SF6DC
0CE226SF6DC
0CE476SF6DC
0CE105SK6DC
0CE105SK6DC
0CE226SF6DC
0CE105SK6DC
0CE226SF6DC
KDS184 85V 300MA
KDS226 TP KEC
KDS184 85V 300MA
KDS226 TP KEC
EU1ZV(1) TP SANKEN
LED,SAM2333
LED,SAM2333
LED,SAM2333
LED,SAM2333
LED,SAM2333
KDS184 TP KEC - 85V 300MA
LED,SAM5670(DL-2LRG)
SD05.TC SOD323 5V 5A 15A
SD05.TC SOD323 5V 5A 15A
SD05.TC SOD323 5V 5A 15A
SD05.TC SOD323 5V 5A 15A
1UF HI STABILITY 50V 10%
1UF HI STABILITY 50V 10%
10UF MVG 16V 20%
10UF MVG 16V 20%
1UF MVG 50V 20%
22UF MVG 16V 20%
10UF MVG 16V 20%
100UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
100UF MVG 16V 20%
1UF 2012 16V 20%
1UF 2012 16V 20%
1000UF STD 35V 20%
0.47UF D 63V 5%
0.47UF D 63V 5%
47UF MVG 16V 20%
1000UF STD 35V 20%
100UF MVG 16V 20%
100UF MVG 16V 20%
47UF MVG 16V 20%
100UF MVG 16V 20%
47UF MVG 16V 20%
100UF MVG 16V 20%
47UF MVG 16V 20%
22UF MVG 16V 20%
47UF MVG 16V 20%
1UF MVG 50V 20%
1UF MVG 50V 20%
22UF MVG 16V 20%
1UF MVG 50V 20%
22UF MVG 16V 20%
CAPACITOR
REPLACEMENT PARTS LIST
DIODE

- 20 -
LOCA. NO PART NO DESCRIPTION
C150
C156
C157
C158
C1606
C1607
C161
C161
C1610
C165
C166
C167
C169
C170
C171
C172
C174
C202
C202
C205
C206
C207
C208
C212
C213
C214
C214
C215
C216
C217
C223
C224
C232
C233
C234
C235
C236
C236
C238
C239
C243
C244
C245
C251
C252
C253
C254
C255
C260
C264
C265
0CE476SF6DC
0CE105SK6DC
0CE477SF6DC
0CE105SK6DC
0CE226SF6DC
0CE226SF6DC
0CE105SK6DC
0CE107SF6DC
0CE226SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE4763F618
0CE226SF6DC
0CE476SF6DC
0CE226SF6DC
0CE477DJ618
0CE226SF6DC
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE106SF6DC
0CE477DJ618
0CE477SF6DC
0CE477SF6DC
0CE477SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE106SF6DC
0CE226SF6DC
0CE226SF6DC
0CE477SF6DC
0CE477SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE476SF6DC
0CE107SF6DC
0CE107SF6DC
47UF MVG 16V 20%
1UF MVG 50V 20%
470UF MVG 16V 20%
1UF MVG 50V 20%
22UF MVG 16V 20%
22UF MVG 16V 20%
1UF MVG 50V 20%
100UF MVG 16V 20%
22UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
47UF SRE 16V M
22UF MVG 16V 20%
47UF MVG 16V 20%
22UF MVG 16V 20%
470UF STD 35V 20%
22UF MVG 16V 20%
470UF MVG 16V 20%
470UF MVG 16V 20%
470UF MVG 16V 20%
10UF MVG 16V 20%
470UF STD 35V 20%
470UF MVG 16V 20%
470UF MVG 16V 20%
470UF MVG 16V 20%
100UF MVG 16V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
100UF MVG 16V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
10UF MVG 16V 20%
22UF MVG 16V 20%
22UF MVG 16V 20%
470UF MVG 16V 20%
470UF MVG 16V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
100UF MVG 16V 20%
100UF MVG 16V 20%
LOCA. NO PART NO DESCRIPTION
C266
C272
C274
C280
C295
C297
C298
C299
C301
C303
C304
C308
C309
C310
C310
C311
C312
C313
C315
C315
C316
C317
C322
C323
C325
C329
C330
C331
C332
C333
C334
C335
C336
C343
C348
C349
C350
C351
C352
C353
C357
C367
C369
C370
C379
C380
C383
C406
C408
C411
C412
0CE107SF6DC
0CE476SF6DC
0CE226SF6DC
0CE335VK6DC
0CE335VK6DC
0CE107SF6DC
0CE106SF6DC
0CE106SF6DC
0CK684DF56A
0CE226SF6DC
0CE476SF6DC
0CE105SK6DC
0CE476SF6DC
0CE476SF6DC
0CE106SF6DC
0CE226SF6DC
0CE226SF6DC
0CE106SF6DC
0CK684DF56A
0CE476VK6DC
0CE476SF6DC
0CE226SF6DC
0CE106SF6DC
0CE226SF6DC
0CE106SF6DC
0CE476SF6DC
0CE476SF6DC
0CE106SF6DC
0CE106SF6DC
0CE106SF6DC
0CE335VK6DC
0CE226SF6DC
0CE225VK6DC
0CK823DK56A
0CE476SF6DC
0CE226SF6DC
0CE106SF6DC
0CE477SF6DC
0CE226SF6DC
0CE106SF6DC
0CE476SF6DC
0CE105SK6DC
0CE105SK6DC
0CE105SK6DC
0CE226SF6DC
0CE106SF6DC
0CE476SF6DC
0CE477SF6DC
0CE106SF6DC
0CE105SK6DC
0CE225VK6DC
100UF MVG 16V 20%
47UF MVG 16V 20%
22UF MVG 16V 20%
3.3UF MV 50V 20%
3.3UF MV 50V 20%
100UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
0.68UF 2012 16V 10%
22UF MVG 16V 20%
47UF MVG 16V 20%
1UF MVG 50V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
10UF MVG 16V 20%
22UF MVG 16V 20%
22UF MVG 16V 20%
10UF MVG 16V 20%
0.68UF 2012 16V 10%
47UF MV 50V 20%
47UF MVG 16V 20%
22UF MVG 16V 20%
10UF MVG 16V 20%
22UF MVG 16V 20%
10UF MVG 16V 20%
47UF MVG 16V 20%
47UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
10UF MVG 16V 20%
3.3UF MV 50V 20%
22UF MVG 16V 20%
2.2UF MV 50V 20%
82000PF 2012 50V 10%
47UF MVG 16V 20%
22UF MVG 16V 20%
10UF MVG 16V 20%
470UF MVG 16V 20%
22UF MVG 16V 20%
10UF MVG 16V 20%
47UF MVG 16V 20%
1UF MVG 50V 20%
1UF MVG 50V 20%
1UF MVG 50V 20%
22UF MVG 16V 20%
10UF MVG 16V 20%
47UF MVG 16V 20%
470UF MVG 16V 20%
10UF MVG 16V 20%
1UF MVG 50V 20%
2.2UF MV 50V 20%
REPLACEMENT PARTS LIST