Life Span BALANCE User manual

Product may vary slightly from the item pictured due to model upgrades
Read all instructions carefully before using this product. Retain this owner’s manual for
future reference.
BALANCE
OWNER’S MANUAL

2
BALANCE
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS 3
2. IMPORTANT ELECTRICAL INFORMATION 4
3. IMPORTANT OPERATING INSTRUCTIONS 5
4. ASSEMBLY INSTRUCTIONS 6
5. FOLDING INSTRUCTIONS 10
7. GROUNDING METHODS 11
8. OPERATION GUIDE 12
9. EXERCISE GUIDE 15
10. MAINTENANCE GUIDE 17
11. EXPLODED DIAGRAM 21
12. PARTS LIST 22
13. TROUBLE SHOOTING GUIDE 25
14. WARRANTY 27
15. PROGRAM GUIDE 28

3
BALANCE
1. IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this treadmill.
It is important your treadmill receives regular maintenance to prolong its useful life. Failing to
regularly maintain your treadmill may void your warranty.
Danger –To reduce the risk of electric shock disconnect your treadmill from the electrical outlet prior to
cleaning and/or service work.
DO NOT USE AN EXTENSION CORD: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY
USING IMPROPER ADAPTERS OR IN ANY WAY MODIFY THE CORD SET.
Install the treadmill on a flat level surface with access to a 220-240 volt (50/60Hz), grounded outlet.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet and
treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 1 metre clearance between the rear of
the treadmill and any fixed object.
Place your unit on a solid, level surface when in use
Never allow children on or near the treadmill.
When running, make sure the plastic clip is fastened on your clothing. It is for your safety, should
you fall or move too far back on the treadmill.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being administered.
Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.

4
BALANCE
The treadmill is intended for in-home use only and not suitable for long time running.
To disconnect, turn all controls to the off position, remove the safety key, and then remove the plug
from the outlet.
The pulse sensors are not medical devices. Various factors, including the user’s movement, may
affect the accuracy of heart rate readings. The pulse sensors are intended only as exercise aids in
determining heart rate trends in general.
Use the handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on your
treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Allowed temperature: 5 to 40 degrees.
Remove the safety key after use to prevent unauthorized treadmill operation.
2. IMPORTANT ELECTRICAL INFORMATION
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power
cord away from any moving part of the treadmill including the elevation mechanism and transport
wheels.
NEVER remove any cover without first disconnecting AC power.
NEVER expose this treadmill to rain or moisture. This treadmill is not designed for use outdoors,
near a pool, or in any other high humidity environment.

5
BALANCE
3. IMPORTANT OPERATING INSTRUCTIONS
Be sure to read the entire manual before operating your machine.
Understand that changes in speed and incline do not occur immediately. Set your desired speed on
the computer console and release the adjustment key. The computer will obey the command
gradually.
Use caution while participating in other activities while walking on your treadmill, such as watching
television, reading, etc. These distractions may cause you to lose balance or stray from walking in
the centre of the belt; which may result in serious injury.
In order to prevent losing balance and suffering unexpected injury, NEVER mount or dismount the
treadmill while the belt is moving. This unit starts with at a very low speed. Simply standing on the
belt during slow acceleration is proper after you have learned to operate this machine.
Always hold on to handrail while making control changes.
A safety key is provided with this machine. Remove the safety key will stop the walking belt
immediately; the treadmill will shut off automatically. Inserting the safety key will reset the display.
Do not use excessive pressure on console control keys. They are precision set to function properly
with little finger pressure.

6
BALANCE
4. ASSEMBLY INSTRUCTIONS
PART LIST
NO.
DES.
Specification
Nos.
NO.
DES.
Specification
Nos.
1
Main Frame
1
39
Lock washer
8
2
5
Strengthening
Pipe
1
88
6#Allen Wrench
6mm
1
21
Basic right cover
1
89
Allen Wrench
S=13\14\15mm
1
22
Basic left cover
1
90
5#Allen Wrench
5mm
1
61
Bolt
M10*60
2
79
Safety lock
1
63
screw
ST4.2*19
4
95
Bolt
M8*48
2

7
BALANCE
44
Lock washer
10
2
STEP 1:
STEP 2:
STEP 3:
1. Open the carton
2. Extract the parts listed above
3. Place the Main Frame (#1) onto level
ground
1. Use the #5 Allen wrench to pull up the
M8*45 screw (60), lock the console
frame onto the left & right Upright.
Note: Whilst erecting the uprights, make sure
the upright does not press against and
damage the wires inside the upright tubes.
Keep holding the upright and computer by
hand so they do not fall down and cause
injury
1. Using the #5 Allen Wrench, loosen
the M8 * 45 screws (60) from the left
and right upright tubes.

8
BALANCE
STEP 4:
STEP 5:
1. Use the 5# Allen wrench (90), M8*48
screw (95) and lock washer (39) to lock
the left upright onto the base frame.
2. Use 6# Allen wrench (88), M8*48 screw
(61) and lock washer (44) to lock the left
upright onto the base frame.
3. Repeat the above to assemble the right
upright
NO.95 is for M8
NO.61 is for M10
1. Use the #5 Allen wrench, M8*55 screw
(58) and lock washer (39) to fix the
computer bracket onto both uprights
(3\4).

9
BALANCE
STEP 6:
1. Use wrench screw driver and
ST4.2*19 screw (63) to fix the base
right cover (21) onto the left upright
and base.
2. Use wrench screw driver and
ST4.2*19 screw (63) to fix the base
left cover (22) onto the right upright
and base.

10
BALANCE
5. FOLDING INSTRUCTIONS
Folding:
Unfolding:
Erect the base frame using position A until
you hear the click sound emitted when the
air pressure bar B is locked into the round
tube.
Whilst supporting position A with our
hand, gently push the marked area on
the air pressure bar with your foot.
The base frame will descend
automatically. (Please keep people and
any pets away the machine during
descent)