Life Span dominator User manual

Product may vary slightly from the item pictured due to model upgrades
DOMINATOR
OWNER'S MANUAL
- -
DOMINATOR
0

1. IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this treadmill.
It is important your treadmill receives regular maintenance to prolong its useful life. Failing
to re
g
ularl
y
maintain
y
our treadmill ma
y
void
y
our warrant
y
.
Danger–To reduce the risk of electric shock disconnect your treadmill from the electrical outlet prior
to cleaning and/or service work.
DO NOT USE AN EXTENSION CORD: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG
BY USING IMPROPER ADAPTERS OR IN ANY WAY MODIFY THE CORD SET.
Install the treadmill on a flat level surface with access to a 220-240 volt (50/60Hz), grounded
outlet.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet and
treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 1 metre clearance between the rear
of the treadmill and any fixed object.
Place your unit on a solid, level surface when in use.
Never allow children on or near the treadmill.
When running, make sure the plastic clip is fastened on your clothing. It is for your safety, should
you fall or move too far back on the treadmill.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
- -
DOMINATOR
1

- -
DOMINATOR
2
Never drop or insert any object into any openings.
The treadmill is intended for in-home use only and not suitable for long time running.
To disconnect, turn all controls to the off position, remove the safety key, and then remove the
plug from the outlet.
The pulse sensors are not medical devices. Various factors, including the user’s movement, may
affect the accuracy of heart rate readings. The pulse sensors are intended only as exercise aids in
determining heart rate trends in general.
Use handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on your
treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Allowed temperature: 5 to 40 degrees.
Remove the safety key after use to prevent unauthorized treadmill operation.
1.1 IMPORTANT ELECTRICAL INFORMATION
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power
cord away from any moving part of the treadmill including the elevation mechanism and transport
wheels.
NEVER remove any cover without first disconnecting AC power.
NEVER expose this treadmill to rain or moisture. This treadmill is not designed for use outdoors,
near a pool, or in any other high humidity environment.
1.2 IMPORTANT OPERATION INSTRUCTIONS
Be sure to read the entire manual before operating your machine.
Understand that changes in speed and incline do not occur immediately. Set your desired speed
on the computer console and release the adjustment key. The computer will obey the command
gradually.

- -
DOMINATOR
3
Use caution while participating in other activities while walking on your treadmill; such as
watching television, reading, etc. These distractions may cause you to lose balance or stray from
walking in the centre of the belt; which may result in serious injury.
In order to prevent losing balance and suffering unexpected injury, NEVER mount or dismount
the treadmill while the belt is moving. This unit starts with at a very low speed. Simply standing
on the belt during slow acceleration is proper after you have learned to operate this machine.
Always hold on to handrail while making control changes.
A safety key is provided with this machine. Remove the safety key will stop the walking belt
immediately; the treadmill will shut off automatically. Insert the safety key will reset the display.
Do not use excessive pressure on console control keys. They are precision set to function
properly with little finger pressure.

ASSEMBLY INSTRUCTIONS
When you open the carton, you will find the below spare parts:
1COMPUTER
2.LEFT
HANDLEBAR
ASSEMBLY
3.RIGHT
HANDLEBAR
ASSEMBLY
4.FIXED RAIL TUBE 5. LEFT UPRIGHT
6.RIGHT
UPRIGHT
74.LEFT
OUTSIDE
PLASTIC COVER
75.RIGHT
OUTSIDE
PLASTIC COVER
20 BOLT M10*25 22BOLT M8*52
38 FLAT
WASHER 8
34.SCREW
ST4.2*12 19 BOLT M8*26 42 FLAT
WASHER 10 8MAIN FRAME
61 WRENCH
W/SCREW
DRIVER
59 6# ALLEN
WRENCH 6mm
60 5# ALLEN
WRENCH 5mm
FIXING TOOLS:
ALLEN WRENCH :6mm 1 pcs ALLEN WRENCH: 5mm 1 pcs
- -
DOMINATOR
4

WRENCH W/SCREW DRIVER: 13*15 1 pcs
ASSEMBLY STEPS
Step 3：
5. Connect the computer right cable
between computer frame and right upright.
6. Insert computer frame into left upright
and right upright. Connect them with the
bolts M10*25 (20) and flat washer (42).
CAUTION: Tighten all the bolts again.
Step 2：
3. Connect the fixed rail tube (4) with the
bolts M8*26 (19), the bolts M8*52 (22) and
flat washer (42).
4. Insert left upright (5) & right upright (6)
into main frame. Connect them with the bolts
M10*25 (20) and flat washer (42).
CAUTION:
A. Please don’t damage the wires in the
process.
B. Please don’t tighten ALL BOLTS before
STEP
(
3
)
.
Step 1：
1. Connect the computer wires on the left
and right handlebar assembly (2&3) and
with bolts M8*52 (22) & flat washer (38) to
tighten the left and right handlebar
assembly and computer.
2. To lock the left and right outside plastic
cover with screw ST4.2*12 (34).
- -
DOMINATOR
5

--
DOMINATOR
6
CAUTION:
1. DO NOT PLUG IN POWER CORD UNTIL FINAL ASSEMBLY IS COMPLETED AND MOTOR
COVER IS INSTALLED.
2. Do not attempt to assemble the treadmill unless the assembly instructions are followed and the
uprights are attached to the treadmill. Failure to follow this can result in damage to the treadmill.
3. Your treadmill is a very heavy piece of exercise equipment so should be handled with caution.
4. Children should not be allowed to play on the treadmill or move the treadmill deck up and down.
TECHNICAL PARAMETER
BUILT UP SIZE(mm) 1980*910*1325 POWER 220V~240V(50~60HZ)
RUNNING BELT SIZE(mm) 3150*520 SPEED RANGE 1—20 Km/h
FOLDABLE SIZE(mm) 890*910*1790 NET WEIGHT 117.5KGS
SIGNAL BLUE
BACKGROUND DISPLAY
SPEED, DISTANCE, CALORIES, PULSE, TIME and INCLINE

EXERCISE GUIDE
PLEASE NOTE: Before beginning any exercise program, consult you physician. This is
important especially if you are over the age of 45 or individuals with pre-existing health
problems.
The pulse sensors are not medical devices. Various factors, including the user’s movement,
may affect the accuracy of heart rate readings. The pulse sensors are intended only as an
exercise aid in determining heart rate trends in general.
Exercising is great way to control your weight, improving your fitness and reduce the effect of aging
and stress. The key to success is to make exercise a regular and enjoyable part of your everyday life.
The condition of your heart and lungs and how efficient they are in delivering oxygen via your blood to
your muscles is an important factor to your fitness. Your muscles use this oxygen to provide enough
energy for daily activity. This is called aerobic activity. When you are fit, your heart will not have to work
so hard. It will pump a lot fewer times per minute, reducing the wear and tear of your heart.
So as you can see, the fitter you are, the healthier and greater you will feel.
Warm-up
Start each workout with 5 to 10 minutes of stretching and some light exercises. A proper warm-up
increases your body temperature, heart rate and circulation in preparation for exercise. Ease into your
exercise.
- -
DOMINATOR
7

Training zone Exercise
After warming up, increase the intensity to your desired exercise program. Be sure to maintain your
intensity for maximum performance. Breathe regularly and deeply as you exercise-never hold your
breathe.
Cool Down
Finish each workout with a light jog or walk for at least 1 minute. Then complete 5 to 10 minutes of
stretching to cool down. This will increase the flexibility of your muscles and will help prevent
post-exercise problems.
Workout Guidelines
TARGET ZONE
THIS IS HOW YOUR PULSE SHOULD BEHAVE DURING GENERAL FITNESS
EXERCISE. REMEMBER TO WARM UP AND COOL DOWN FOR A FEW MINUTES.
The most important factor here is the amount of effort you put in. The harder and longer
you work the more calories you will burn. Effectively this is the same as if you were
- -
DOMINATOR
8

training to improve your fitness, the difference is the goal.
OPERATION GUIDE
Window & Button explanation:
1、Window display:
PULSE window displays pulse；TIME window displays time；DISTANCE
window displays distance；CAL window displays calories；INCLINE window
displays incline；SPEED window displays speed；The middle of display window
displays speed and incline, oval display means 400 racetrack, LAPS means
circles.
2、Function button:
POWER、START/STOP、SELECT、ENTER、INCLINE▲、INCLINE▼、SPEED▼、
SPEED▲、SPEED SHORTCUT KEY(RIGHT 10)、INCLINE SHORTCUT KEY
(LEFT 10).
3、Function button explanation:
A. POWER ：When you open the power switch and press POWER
- -
DOMINATOR
9

- -
DOMINATOR
10
button,theTIME window displays 70 (70 means the weight setting, the unit is KG.
When the user resets and saves it, then it will display the save value).The user
can adjust the speed up or down and incline up or down according to his own
actual weight.
B. ENTER: setting the weight and pressing ENTER button, it will enter into the next step.
C. SELECT：Pressing SELECT button can recurrent select and set up the exercise time and
program. P0->P1->P2->P3->P4->P5->P6->P7->P8->P9->U1->U2->U3 （P0 is manual
mode,P1-P9 is system fixed program,U1, U2, U3 is left setting programs.）
D. SPEED▼& SPEED▲: When the system setting, press SPEED▼& SPEED▲can
adjust the exercise time. When the treadmill is running, it can adjust the speed.
E. INCLINE▲& INCLINE▼：When the system setting, press INCLINE▲& INCLINE▼
can adjust the exercise time. When the treadmill is running, it can adjust the incline.
F. START/STOP: The button is a mulriple button, when the user chooses the system
program or after setting the exercise time, then press START/STOP button and the
system will enter into 3 seconds count down. The buzzer will make sound and the
speed window displays count down, then the treadmill will start after 3 seconds. When
the treadmill is running,the button can control the PAUSE or RESET.When the treadmill
stops, the incline and the speed are 0, the calories, time and distance will stop counting,
then it will go on counting after it gets back running.
G.SPEED SHORTCUT KEY: When the treadmill is running, pressing the SPEED
SHORTCUT KEY will adjust the speed to be exactly you need.
H. INCLINE SHORTCUT KEY: When the treadmill is running, pressing the INCLINE
SHORTCUT KEY will adjust the incline to be exactly you need.

- -
DOMINATOR
11
Program explanation:
SPEED，INCLINE（Divided into 20 incline and each incline is the 1/20 of the
general incline）.
TIME INTERVAL
MODE 1 2 3 4 5 67891011121314151617181920
SPEED 2 3 3 4 5 345534544423353
P1 INCLINE 1 1 2 2 2 332212221133222
SPEED 2 4 4 5 6 466645644422542
P2 INCLINE 1 2 2 2 2 332222233344322
SPEED 2 4 4 6 6 477747744424532
P3
INCLINE 2 3 3 2 2 333222244466322
SPEED 3 5 5 6 7 757788595566443
P4 INCLINE 2 3 3 2 2 333222244466322
SPEED 2 4 4 5 6 775678854336542
P5 INCLINE 3 3 3 4 4 555444455333222
SPEED 2 4 4 4 5 688678864425432
P6 INCLINE 3 5 5 5 4 443333444333432
SPEED 2 3 3 3 4 534534533366533
P7 INCLINE 4 4 4 4 3 366677889966533
SPEED 2 3 3 6 7 746746744423442
P8 INCLINE 4 5 5 5 6 66789991010101212863
SPEED 2 4 4 7 7 478489944456332
P9 INCLINE 5 5 5 6 6 644665588999742
START-UP QUICKLY (MANUAL)
1、Open the power switch, attach the magnet end of the safety pulling rope to the
computer.
2、Press POWER button, TIME display window displays weight/time.
3、Press START/STOP button，the system will enter into 3 seconds count down, the
buzzer will make sound and the time window display counts down, the speed will run
1.0km/hour after 3 seconds.
4、After start-up, you can use speed up or down to adjust the speed and use incline up or
down to adjust the incline.

- -
DOMINATOR
12
USER PROGRAM OPERATION
1. Press SELECT button to user programs (U1, U2, U3). First; press ENTER，the time
will be divided into 20 intervals.
2. Select the speed you want by SPEED UP or SPEED DOWN for the first interval,
select the incline you want by INCLINE UP or INCLINE DOWN for the first interval.
3. Then press ENTER to select the speed and incline for the second interval.
4. Repeat Step 3 to set up the speed and incline for all 20 intervals. The computer will
then display “OK”.
5. Press START to enjoy your own setup user programs.
The operation of exercise process:
1、Press speed-down will reduce the running speed.
2、Press speed-up will increase the running speed.
3、Press incline-down will reduce the incline.
4、Press incline-up will increase the incline.
5、Press speed shortcut key will adjust to the relevant speed directly.
6、Press incline shortcut key will adjust to the relevant incline directly.
7、Press START/PAUSE will reduce until it stops.
8、Press POWER button can stop the treadmill.
9、When the user holds the hand pulse about 5 seconds, it will display pulse data.
Close up:
1、Close up the power: You can close up the power to stop the treadmill; it won’t be
damaged at any time.
2、Press the POWER button to close up: You can press the power button to stop the
treadmill, when you press the power button again, the treadmill will be awaiting
orders.
SAFETY LOCK FUNCTION:
Pull out the safety pulling rope, then the treadmill will stop immediately. All the
windows display“―――”，the buzzer will make a“BB”sound ceaselessly. Attach
the magnet end of the safety pulling rope to the computer; the treadmill will be at the
beginning of running.
CAUTION:
1. We recommend that you maintain a slow speed at the beginning of a session and hold
on to the handrails until you become comfortable and familiar with the treadmill.
2. Attach the magnet end of the safety pulling rope to the computer and also attach the
clip of the safety pulling rope to your clothing.
3. To end your workout safely, press the STOP button or pull out the safety pulling rope,
then the treadmill will stop immediately.

- -
DOMINATOR
13
RANGE OF PROGRAM
PROGRAM BEGIN BEGIN TO SET UP SET UP RANGE
TIME （MINUTE ：
SECOND）0:00 15:00 10:00-99:00 0:00－99:59
SPEED（KM/H）0.0 N/A N/A 1.0－20.0
DISTANCE（KM）0.00 0.0 N/A 0.00－99.90
INCLINE 0 0 0-20 0-20
HANDPULSE
（TIMES/MINUTE）P N/A N/A 40－199
CALORIES(THERM) 0 0 N/A 0－999
WEIGHT 70 70 50－125 50－125
TROUBLESHOOTING GUIDE
TROUBLESHOOTING GUIDE
PROBLEM CAUSE CHECKING CORRECTION
1.If the plug and the line is
loosen.
1. Checking the plug and
the line is connected well.
1. Insert the plug and the line
well.
Treadmill
will not
start. 2.Not plugged in.
2.Checking the power
switch is opened.
2. Reset the power.
1.The relative line of the
control motor is abnormal.
1.Checking the line of the
control motor is plugged
well.
1. Insert the control motor wire.
2.Do not press START KEY.
2.Checking the button is
valid or not started the
switch.
2. Reset the START KEY to
test.
The motor
will not
work.
3.Safety pull pin not inserted
3.Checking the safety pull
pin is plugged well.
3.Insert safety pull pin.

- -
DOMINATOR
14
4.Motor plug is loosen or the
motor is faulty.
4.Testing if the motor is
faulty.
4.Change the motor
5.Power or controller
specification is
wrong.(AC220~240V)
5.Checking the
specification.
5.To choose the correct
specification to reset the
testing.
1.Checking the distance
and place between
SENSOR and magnet.
1.Adjust the distance within
5m/m.
2.Checking the wire if
circuit breaker tripped.
2.Change the wire or SENSOR
No speed SENSOR does not touch
well.
3.Checking the wire tie-in
if it is touched well.
3.Reset to insert the wire tie-in.
PA circuit
board
Pa circuit board bolt does not
lock well or not put well the
connector.
Take apart the bottom
cover and press PA circuit
board to see if it is short
circuit or loosen.
Reset to put the connector and
lock the bolt.
1.Checking the wire is
short circuit or loosen.
1.Change the wire or reset.
SENSOR does not touch
well.
2.Checking the wire and
computer if the tie-in is
connected well.
2.Reset to insert the wire
No hand
pulse
The hand pulse does not
touch well
3.Put both hands to bedew
a little or scrub with both
hands.
3.Reset to test.
E01 Message failure
1.the connected wire is
wrong.
1.Use the multimeter to test the
wire is stand or fall.

- -
DOMINATOR
15
2.To test the outside and the
side voltage is normal.
（DC12V）
in
2.Power supply voltage is
of shortage
3.SCM is bad.
1．Power tube badness 1．Change the power tube
2．Drivers badness 2．Change the drivers
E02 burst clash
3．Motor is failure 3．Change the motor
1.Sensor wire badness 1．Change the sensor wire
2．It is no use for the motor
magnetic.
2．Change the magnetic or
reset the magnetic
E03 No sensor signal
3．Drivers badness 3．Change the drivers
1．Study failure 1．To reset study
2. Incline motor badness 2．Change the incline motor
3．Drivers badness 3．Change 24C02 or change
the drivers
E04 Incline study failure
4．Incline motor wire does
not connect well 4．Insert the incline motor wire.
1．The limited weight 1．Do not exceed the treadmill
user’s maximum weight.
2．Drivers badness
2．Change the limited
resistance or change the
drivers
E05 Over loading protector
3．Voltage is wrong 3．Test the usage voltage is
measure up
1．The machine is
interfered 1．Reset the treadmill
E06 System testing failure
2．Drivers badness 2．Change IGBT or change
drivers.
1．Safety lock badness 1．Change the safety lock
E07 Out of safety lock
2．Computer badness
2．Test the iron piece of the
safety lock is dropped out or
change the computer.
E08 24C02 message failure 1．Data transfer failure 1．Change 24C02 EEPROM
IC

MAINTENANCE INSTRUCTIONS
Reasonable cleaning/lubricating should be made to extend the life time of this unit. Performance is
maximized when the belt and mat are kept as clean as possible.
WARNING: THE MAT/DECK FRICTION MAY PLAY A MAJOR ROLE IN THE FUNCTION AND
LIFE OF YOUR TREADMILL AND THAT IS WHY WE RECOMMEND YOU CONSTANTLY
LUBRICATE THIS FRICTION POINT TO PROLONG THE USEFUL LIFE OF YOUR TREADMILL.
FAILING TO DO THIS MAY VOID YOUR WARRANTY.
.ECNANETNIAMEROFEBDROCREWOPGULPNU:GNINRAW
WARNING: STOP TREADMILL BEFORE FOLDING.
1 Maintenance and servicing
AFTER EACH USE (DAILY)
Clean and inspect, following these steps:
• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
• Wipe down the running belt, deck, motor cover, and console casing with a damp cloth. Never
use solvents, as they can cause damage to the treadmill.
• Inspect the power cord. If the power cord is damaged, contact Lifespan Fitness.
• Make sure the power cord is not underneath the treadmill or in any other area where it can
become pinched or cut.
• Check the tension and alignment of the running belt. Make sure that the treadmill belt will not
damage any other components on the treadmill by being misaligned.
EVERY WEEK
Clean underneath the treadmill, following these steps:
• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
• Fold the treadmill into the upright position, making sure that the lock latch is secure.
• Move the treadmill to a remote location.
• Wipe or vacuum any dust particles or other objects that may have accumulated underneath the
treadmill.
• Return the treadmill to its previous position.
--
DOMINATOR
16

EVERY MONTH -IMPORTANT!
• Inspect all assembly bolts of the machine for proper tightness.
• Turn off the treadmill with the on/off switch, then unplug the power cord and wait 60 seconds.
• Remove the motor cover. Wait until ALL LED lights turn off.
• Clean the motor and lower board area to eliminate any lint or dust particles that may have accumulated.
Failure to do so may result in premature failure of key electrical components.
EVERY 6 MONTHS
It may be necessary to lubricate your treadmill running deck at least once every six months to maintain
optimal performance of your treadmill (refer to section 4.4 for information). Only use lubricant provided
by Lifespan Fitness! Please contact Lifespan Fitness with questions about applying lubricant to your
treadmill.
• Turn off the treadmill with the on/off switch, then unplug the power cord at the wall outlet.
• Loosen both the rear roller bolts. (For best results, place two removable marks on both sides of the
frame and note roller position).Once the belt is loosened, take the bottle of lubricant and apply it to the
entire top surface of the running deck. Tighten both rear roller bolts (matching up the marks for proper
position) to original position. After you have applied lubricant, plug in the power cord, key, start the
treadmill and walk on the belt for two minutes to spread the lubricant.
• Lubricate the air shocks with Teflon based spray.
EVERY 2 YEARS
It is necessary that you change your treadmill motor brushes once every 2 years to avoid damaging
your motor. If you fail to change the brushes this may cause the motor to burn out, voiding any
warranty.
--
DOMINATOR
17
2 General Cleaning
Use a soft, damp cloth to wipe the edge of the belt and the area between the belt edge and
frame. A mild soap and water solution along with a nylon scrub brush will clean the top of the
textured belt. This task should be done once a month. Allow to dry before using.
On a monthly basis, vacuum underneath your treadmill to prevent dust build up. Once a year,
you should remove the black motor shield and vacuum out dirt that may accumulate.
3 General Care
Check parts for wear before use.
Pay particular attention to the fixing knobs and make sure they are tight.
Always replace the mat if worn and any other defective parts.
If in doubt do not use the treadmill and contact our helpline.
SERVICING: IF YOU FAIL TO COMPLY WITH LIFESPAN’S MAINTENANCE AND SERVICING STEPS
ABOVE, YOU MAY VOID YOUR WARRANTY. IF YOU REQUIRE A SKILLED LIFESPAN REPRESENTATIVE TO
UNDERTAKE ONE OF THE STEPS ABOVE, PLEASE EMAIL US AT [email protected].
PLEASE NOTE: TREADMILL MOTOR BRUSHES NEED TO BE CHANGED EVERY 2 YEARS
OTHERWISE MOTOR WARRANTY WILL BE VOID.REFER TO MANUAL

--
DOMINATOR
18
TAKE CARE TO PROTECT CARPETS AND FLOOR in case of leakages. This product is a machine
that contains moving parts which have been greased / lubricated and could leak.
4 Belt/Deck/Roller Lubrication:
The mat/deck friction may play a major role in the function and life of your treadmill and that is why we
recommend you constantly lubricate this friction point to prolong the useful life of your treadmill.
Lubrication is provided with this unit. You should apply the enclosed lubrication after approximately the
first 50 hours of operation. We recommend lubrication of the deck according to the following timetable:
Light use (less that 3 hours per week) every 6 months
Medium use (3-5 hours a week) every 3 months
Heavy use (more than 5 hours per week) every 6-8 weeks.
See below procedures for lubricating:
1. Use a soft, dry cloth to wipe the area between the belt and deck.
2. Spread lubricant onto the inside surface of belt and deck evenly (make sure the machine is turned
off and power is disconnected).
3. Periodically lubricate the front and rear rollers to keep them at there peak performance.
If the treadmill belt/deck/roller is kept reasonably clean it is possible to expect over 1200 hours before
additional re-lubing is necessary.
5 How to check the running mat for proper lubrication:
1. Disconnect the main power supply.
2. Fold the treadmill up into the storage position.
3. Feel the back surface of the running mat.
If the surface is slick when touched, then no further lubrication is needed.
If the surface is dry to the touch, apply a suitable silicone lubricant.
We recommend you use a silicone based spray to lubricate your Lifespan Treadmill. This Can
be purchased from your local sports Retailer or a local hardware store.

--
DOMINATOR
19
6 Belt Adjustment
Belt Tension Adjustment-It is very important for joggers and runners in order to provide a
smooth, steady running surface. Adjustment must be made from the right and left rear roller in order to
adjust tension with the Allen Key provided in the parts package. The adjustment bolt is located at the
end of the rails as noted in diagram below:
Left bolt Right bolt
Note: Adjustment is thru small hold of end cap.
Tighten the rear roller only enough to prevent slippage at the front roller. Turn both the right and left
bolt clockwise one full turn and inspect for proper tension. When an adjustment is made to the belt
tension, you must also make a tracking adjustment to compensate for the change in belt tension.
DO NOT OVER TIGHTEN - Over tightening will cause belt damage and premature bearing failure.
This may also cause reduced motor performance and excessive roller wear.
NOTE: When properly tightened, the sides of belt can be raised approximate 2-3 inches off the board.
7Belt Tracking Adjustment:
This treadmill is designed to keep the belt reasonably centred while in use. It is normal for some
belts to drift near one side while the belt is running with no one on it. After a few minutes of use, the
belt should have a tendency to centre itself. If during use, the belt continues to move toward one