Life Span SPRINTER XL User manual

Product may vary slightly from the item pictured due to model upgrades
LIFESPAN SPRINTER Page0
SPRINTER XL
USER’S
MANUAL

CONTENTS
1 IMPORTANT SAFETY INSTRUCTIONS ……………………………………………….. 2
1.1 IMPORTANT ELECTRICAL INFORMATION ………………………………………………..
3
1.2 IMPORTANT OPERATIONAL INSTRUCTIONS ………………………………………………..
3
1.3 KEY COMPONENTS OF THE TREADMILL ………………………………………………..
4
2 ASSEMBLY INSTRUCTIONS ………………………………………………..
5
3 DISPLAY PANEL OPERATIONS ………………………………………………..
7
3.1 CONSOLE LAYOUT ………………………………………………..
7
3.2 BASIC CHARACTERS ………………………………………………..
8
3.3 SAFETY KEY ………………………………………………..
8
3.4 CONSOLE DISPLAY STATUS ………………………………………………..
9
3.5 BUTTON OPERATIONS ………………………………………………..
9
3.6 GETTING STARTED ………………………………………………..
10
3.7 PULSE GRIP FEATURE ………………………………………………..
11
3.8 CALORIE DISPLAY ………………………………………………..
11
3.9 MANUAL PROGRAM ………………………………………………..
11
3.10 PROGRAMMABLE OPERATIONS ………………………………………………..
11
3.11 PRESET PROGRAM ………………………………………………..
12
3.12 PROGRAM GRAPHS ………………………………………………..
13
4 MAINTENANCE ………………………………………………..
16
4.1 GENERAL CLEANING ………………………………………………..
16
4.2 GENERAL CARE ………………………………………………..
16
4.3 BELT/DECK/ROLLER LUBRICATION ………………………………………………..
17
4.4 HOW TO CHECK THE RUNNING MAT FOR PROPER LUBRICATION ………………………………………………..
17
4.5 BELT ADJUSTMENT ………………………………………………..
18
4.6 BELT TRACKING ADJUSTMENT ………………………………………………..
19
5 TROUBLESHOOTING ………………………………………………..
19
5.1 TROUBLESHOOTING TABLE ………………………………………………..
20
6 EXERCISE GUIDE ………………………………………………..
21
6.1 WORKOUT GUIDELINES ………………………………………………..
22
7 WARRANTY REGISTRATION ………………………………………………..
23
8 EXPLODED DIAGRAM ……………………………………………….. 24
9 PARTS LIST ……………………………………………….. 25
LIFESPAN SPRINTER Page1

1. IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this treadmill.
It is important your treadmill receives regular maintenance to prolong its
useful life. Failing to regularly maintain your treadmill may void your warranty.
Danger–To reduce the risk of electric shock disconnect your treadmill from the electrical
outlet prior to cleaning and/or service work.
DO NOT USE AN EXTENSION CORD: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG
BY USING IMPROPER ADAPTERS OR IN ANY WAY MODIFY THE CORD SET.
zInstall the treadmill on a flat level surface with access to a 220-240 volt (50/60Hz),
grounded outlet.
zDo not operate treadmill on deeply padded, plush or shag carpet. Damage to both
carpet and treadmill may result.
zDo not block the rear of the treadmill. Provide a minimum of 1 metre clearance
between the rear of the treadmill and any fixed object.
zPlace your unit on a solid, level surface when in use.
zNever allow children on or near the treadmill.
zWhen running, make sure the plastic clip is fastened on your clothing. It is for your
safety, should you fall or move too far back on the treadmill.
zKeep hands away from all moving parts.
zNever operate the treadmill if it has a damaged cord or plug.
zKeep the cord away from heated surfaces.
zDo not operate where aerosol spray products are being used or where oxygen is being
administered. Sparks from the motor may ignite a highly gaseous environment.
zNever drop or insert any object into any openings.
zThe treadmill is intended for in-home use only and not suitable for long time running.
zTo disconnect, turn all controls to the off position, remove the safety key, and then
remove the plug from the outlet.
LIFESPAN SPRINTER Page2

LIFESPAN SPRINTER Page3
zThe pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
zUse handrails provided; they are for your safety.
zWear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for
use on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
zAllowed temperature: 5 to 40 degrees.
Remove the safety key after use to prevent unauthorized treadmill operation.
1.1 IMPORTANT ELECTRICAL INFORMATION
WARNING!
zNEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route
the power cord away from any moving part of the treadmill including the elevation
mechanism and transport wheels.
zNEVER remove any cover without first disconnecting AC power.
zNEVER expose this treadmill to rain or moisture. This treadmill is not designed for use
outdoors, near a pool, or in any other high humidity environment.
For your information, please note following electronical specification of Treadmill:
a). The rated power input is 850-900W;
b), The power voltage supply is 240V±10%;
c), The rated frequency is 50-60Hz;
1.2 IMPORTANT OPERATION INSTRUCTIONS
zBe sure to read the entire manual before operating your machine.
zUnderstand that changes in speed and incline do not occur immediately. Set your
desired speed on the computer console and release the adjustment key. The computer
will obey the command gradually.

zUse caution while participating in other activities while walking on your treadmill; such
as watching television, reading, etc. These distractions may cause you to lose balance
or stray from walking in the centre of the belt; which may result in serious injury.
zIn order to prevent losing balance and suffering unexpected injury, NEVER mount or
dismount the treadmill while the belt is moving. This unit starts with at a very low
speed. Simply standing on the belt during slow acceleration is proper after you have
learned to operate this machine.
zAlways hold on to handrail while making control changes.
zA safety key is provided with this machine. Remove the safety key will stop the
walking belt immediately; the treadmill will shut off automatically. Insert the safety
key will reset the display.
zDo not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure.
1.3KEYCOMPONANTSOFTREADMIL
Safety Key
Running Mat
Deck- Underneath
the running mat
Motor Cover
Hand Rails
Hand Pulse
Display
Belt AdjustmentTransportation Wheels
LIFESPAN SPRINTER Page4

2 ASSEMBLY INSTRUCTIONS
I II III
IV VVI
76 77
HARDWARE BAG CONTAINING:
Parts# Description Remarks Qty.
I Bottom parts 1
II Left handle 1
III Right handle 1
IV Computer assembly 1
V Horizontal support 1
VI Vertical support 2
TOOLS REQUIRED:
Description Remarks Qty.
Cross ringent wrench S13、S14、S15 1
Inner six-angle wrench S6 1
LIFESPAN SPRINTER Page5

Before assembly, please take out all the parts from the package and align them on the
floor.
LIFESPAN SPRINTER Page6
STEP (1):
1. Connect the wire cable from the
right upright to wire cable coming out
of the main frame firstly; Insert right
and left uprights into main frame, and
then connect them with bolts (4) and
flat washers (16)and
Spring washer（5）by an Allen key
(S6).Then hitch the cover(VI) which is
between left handle(II) and right
handle(III) on the main frame and the
bottom parts(I) ,tighten the cover(VI)
on the main frame with cross-pan self-
locked screw(ST4.2*15 head ￠8)
CAUTION:
Please don’t damage the wires
while assembling the treadmill.
STEP (2):
2. Tighten the vertical support(V) on
the handle(L&R) with pan inner
six-angle screw(M8*55,26) and
D8 flat washer(7).
STEP (3):
3. connect the link line in the
handle bar to the link line in the
computer tube, insert the
computer tube into the L&R
handle, tighten the computer on
the L&R handle with the
screw(M6*12,No.34), D6 spring
washer(9).

CAUTION:
1. DO NOT PLUG IN POWER CORD UNTIL FINAL ASSEMBLY IS COMPLETED AND
MOTOR COVER IS INSTALLED.
2. Do not attempt to assemble the treadmill until the assembly instructions are
followed and the uprights are attached to the treadmill. Failure to follow this can
result in damage to the treadmill.
3. Your treadmill is a very heavy piece of exercise equipment and should be handled
with caution.
4. Children should not be allowed to play on the treadmill or move the treadmill
deck up and down.
WE RECOMMEND YOU HAVE SOMEONE TO ASSIST YOU IN LIFTING AND ASSEMBLING
YOUR LIFESPAN TREADMILL. FOLLOW THESE INSTRUCTIONS CAREFULLY AND IT WILL
MAKE IT EASIER TO ASSEMBLE YOUR LIFESPAN TREADMILL
Ensure all fixings are tightly secured and the treadmill is well constructed.
3 DISPLAY PANEL OPERATIONS
3.1 Console layout
LIFESPAN SPRINTER Page7

LIFESPAN SPRINTER Page8
3.2 Basic Characters
1. Time Range: 0:00~99:59
2. Speed Range: 1~18.00KM/H
3. Distance Range: 0.00~99.9KM
4. Calories range: 0~999CAL
5. Speed, Distance, Calorie and Time can be set in advance. When Distance, Calorie and
Time are set to non-zero value, they have the countdown function.
6. 3 seconds time-suspend startup.
7. Broken-down alarm function
8. Pulse measuring and display
9. Safeguard Function
a. Security device, urgently stop when draw out the safety key.
b. Automatic stop when out of control
There are 15 Buttons in the console panel and 2 control buttons in each handrail.
3.3 Safety Key
IMPORTANT: The treadmill will not operate if the safety key is not in place.
Before starting the treadmill, attach the magnetic key to the display panel, and then attach
the clip on the other end to your clothing (above the waist). If the safety key is removed
whilst you are operation the treadmill, the machine will turn itself off.
When the treadmill is not in use, you should remove the safety key.
Store the safety key in a safe place OUT OF REACH OF CHILDREN.

3.4 Console Display Status
1. STOP
In STOP status, the treadmill belt is not moving, both LED and back light are on.
a. If there is no operation over 10 minutes, it will turn to SLEEP status.
b. Press START button to start running
c. Turn off the safety key, it will turn to OFF status
2. RUNNING
In RUNNING status, the treadmill belt is moving, both LED and back light are on.
a. Press STOP button will stop running
b. Turn off the safety key, it will turn to OFF status
3. SLEEP
In SLEEP status, the treadmill belt stops moving. Both LED and back light are off.
a. If there is any button operation, it will turn to STOP or OFF status
b. If turn on the safety key, it will turn to STOP status
c. If turn off the safety key, it will turn to OFF status.
4. OFF
In OFF status, the treadmill belt stops moving. The LED shows “off” and back light is off.
a. If there is any button operation over 10 minutes, it will turn to SLEEP status
b. If turn on the safety key, it will turn to STOP status
c. There will be no respond when pressing any button.
3.5 Button Operations
Only when the safety key is on, can the user operate the computer that will beep for
every button pressing.
1.START
In STOP status, press START, it will display 3 seconds in TIME window and count down.
When it reached zero, it will turn to RUNNING status and will run at the default speed.
In RUNNING status, press START will not work.
During the 3 seconds counting down, you can press any button to cancel startup and
turn to STOP status.
LIFESPAN SPRINTER Page9

LIFESPAN SPRINTER Page10
STOP
In RUNNING status, press STOP button to stop running and turn to STOP status. Each
window will return to zero automatically.
In STOP status, press STOP will not work.
PROGRAM
In STOP status, press PROGRAM button to choose among P1~P12 or MANUAL
PROGRAM.
In RUNNING status, press PROGRAM to show your current working program. P0
represents the MANUAL PROGRAM.
MODE
In STOP status, when SPEED window showing 0.0, press MODE button to choose
counting up or counting down if you are in MANUAL PROGRAM mode.
In RUNNING status, press MODE will not work.
SPEED UP/ SPEED DOWN
In STOP status, press SPEED UP/ SPEED DOWN will adjust the related window value
where “SET” flash.
In RUNNING status, press SPEED UP/ SPEED DOWN to increase/decrease the speed.
Press SPEED UP/SPEED DOWN once, the speed will increase/decrease 0.1km/h. But if the
speed reaches 18.0km/h, pressing SPEED UP will no longer increase the speed, if the
speed reaches 1.0km/h; pressing SPEED DOWN will no longer decrease the speed. If you
hold the SPEED UP or SPEED DOWN keys for 1 second, the speed will increase or decrease
rapidly.
SPEED UP/ SPEED DOWN in the handrails
The button in the handrails will affect the same function as the SPEED UP/ SPEED
DOWN in the console panel.
3.6 Getting Started
Power the treadmill on by plugging it into an appropriate wall outlet, then turn on the
power switch located at the front of the treadmill below the motor shield. Ensure that the
safety key is installed, as the treadmill will not power on without it.
When the power is turned on, all the lights on the display will light for a short time.

LIFESPAN SPRINTER Page11
3.7 Pulse Grip Feature:
If the computer detects a pulse signal, the PULSE window will show your heart rate beat
per minute instead of “P”. You must use both stainless steel sensors to display your pulse.
Pulse value displays anytime the upper display is receiving a Grip Pulse signal.
3.8 Calorie Display:
Displays the cumulative calories burned at any given time during your workout.
Note: This is only a rough guide used for comparison of different exercise sessions, which
cannot be used for medical purposes.
3.9 Manual Program
The SPEED window will show 0.0 in this mode. You can press MODE button to choose
counting up or time, distance and calories counting down.
a. COUNTING UP
In MANUAL PROGRAM mode, you may press MODE to set time, distance and calories to
zero. When you begin running, the time will count up and distance and calories will count
up from zero. It will stop automatically if the time reaches to 99:59.
b. COUNTING DOWN
In MANUAL PROGRAM mode, you may press MODE to enter the data (except zero) of
time. The data of time will be decreased gradually with exercise. When the data displays
“0”, the treadmill will shut itself off in a short period.
The “SET” will flash and you can set the value in related window.
Press PROGRAM to change from P1 to P12 and MANUAL PROGRAM.
3.10 Programmable Operations
Press PROGRAM button to choose automatic program (from P1 to P12). You can not adjust
the speed when pause training.
Preset programs P1~P12 will be displayed in the SPEED window. You may only need to
preset the time. The default time for each program is 30 minutes. You may choose to
change the program time from the default period of 30 minutes. This is done by simply
using the speed up and speed down keys. Each program has 16 intervals with each

LIFESPAN SPRINTER Page12
interval representing 1/16 of the program time. (Refer to program table and graphs). For
example, if you were to set a program time of 16 minutes, then each interval would be 1
minute. If you were to set a program time of 32 minutes, then each interval would be 2
minutes and so on.
Press PROGRAM to change through P1 to P12 and MANUAL PROGRAM.
3.11 Preset Programs
TIME INTERVALS
PROGRAM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
SPEED 2 3 3 4 5 3 4 5 5 3 4 5 4 4 3 2
P1 INCLINE 1 1 2 2 2 3 3 2 2 1 2 2 2 1
1 1
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 2 4 4 5 6 4 6 6 6 4 5 6 4 3 3 2
P2 INCLINE 1 2 2 2 2 3 3 2 2 2 3 4 3 3
3 2
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 2 4 4 6 6 4 7 7 7 4 7 7 4 4 4 2
P3 INCLINE 2 3 3 2 2 3 3 3 2 2 4 5 6 5
4 3
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 3 5 5 6 7 7 5 7 12 9 6 7 7 5 5 3
P4 INCLINE 2 3 3 2 2 3 3 5 4 3 4 3 3 2
2 1
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 2 4 4 5 6 7 7 5 6 7 12 12 5 4 3 3
P5 INCLINE 3 3 3 4 4 5 5 5 4 4 4 4 5 5
3 3
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 2 4 4 4 5 6 12 12 6 7 12 12 6 4 4 2
P6 INCLINE 3 5 5 5 4 4 4 3 3 3 3 4 4 4
3 3
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 2 3 3 3 4 5 3 4 5 3 4 5 3 3 3 6
P7 INCLINE 4 4 5 5 6 6 7 7 12
12 7 6 6 4 4 2
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 2 3 3 6 7 7 4 6 7 4 6 7 4 4 4 2
P8 INCLINE 4 5 5 6 7 12
9 9 10 10 12 10 12 6 4 2
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 2 4 4 7 7 4 7 12 4 12 9 9 4 4 4 5
P9 INCLINE 5 5 5 6 6 7 7 12
12 6 5 5 6 4 3 2
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 2 4 5 6 7 5 4 6 12 12 6 6 5 4 4 2
P10 INCLINE 5 6 6 6 7 5 12
12 4 4 6 6 7 5 3 2
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 4 4 5 5 6 6 7 12 9 10 12 6 4 4 3 3
P11 INCLINE 2 2 3 4 6 5 4 3 2 2 3 4 5 4
4 2
1 2 3 4 5 6 7 8 9 10
11 12 13 14 15 16
SPEED 3 5 7 9 10 12 10 10 12 12 7 7 6 6 5 5
P12 INCLINE 3 3 5 5 6 6 7 7 5 5 4 4 3 3
2 1

3.12 Program Graphs
P1
0
1
2
3
4
5
6
12345678910111213141516
Intervals
SPEED
INCLINE
P2
0
1
2
3
4
5
6
7
12345678910111213141516
Intervals
SPEED
INCLINE
P3
0
2
4
6
8
12345678910111213141516
Intervals
SPEED
INCLINE
P4
0
2
4
6
8
10
1 2 3 4 5 6 7 8 910111213141516
Intervals
SPEED
INCLINE
LIFESPAN SPRINTER Page13

P5
0
2
4
6
8
10
12345678910111213141516
Intervals
SPEED
INCLINE
P6
0
2
4
6
8
10
12345678910111213141516
Intervals
SPEED
INCLINE
P7
0
2
4
6
8
10
12345678910111213141516
Intervals
SPEED
INCLINE
P8
0
2
4
6
8
10
12
14
12345678910111213141516
Intervals
SPEED
INCLINE
LIFESPAN SPRINTER Page14

P9
0
2
4
6
8
10
12345678910111213141516
Intervals
SPEED
INCLINE
P10
0
2
4
6
8
10
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Intervals
SPEED
INCLINE
P11
0
2
4
6
8
10
12
1 2 3 4 5 6 7 8 9 10111213141516
Intervals
SPEED
INCLINE
P12
0
2
4
6
8
10
12
14
1 2 3 4 5 6 7 8 9 10111213141516
Intervals
SPEED
INCLINE
LIFESPAN SPRINTER Page15

LIFESPAN SPRINTER Page16
4 MAINTENANCE
Reasonable cleaning/lubricating should be made to extend the life time of this unit.
Performance is maximized when the belt and mat are kept as clean as possible.
WARNING: THE MAT/DECK FRICTION MAY PLAY A MAJOR ROLE IN THE
FUNCTION AND LIFE OF YOUR TREADMILL AND THAT IS WHY WE RECOMMEND
YOU CONSTANTLY LUBRICATE THIS FRICTION POINT TO PROLONG THE USEFUL
LIFE OF YOUR TREADMILL. FAILING TO DO THIS MAY VOID YOUR WARRANTY.
WARNING: UNPLUG POWER CORD BEFORE MAINTENANCE.
WARNING: STOP TREADMILL BEFORE FOLDING.
4.1 General Cleaning
zUse a soft, damp cloth to wipe the edge of the belt and the area between the belt
edge and frame. A mild soap and water solution along with a nylon scrub brush will
clean the top of the textured belt. This task should be done once a month. Allow to
dry before using.
zOn a monthly basis, vacuum underneath your treadmill to prevent dust build up.
Once a year, you should remove the black motor shield and vacuum out dirt that may
accumulate.
4.2 General Care
•Check parts for wear before use.
•Pay particular attention to the fixing knobs and make sure they are tight.
•If in doubt do not use the treadmill and contact our helpline.
•Always replace the mat if worn and any other defective parts.

LIFESPAN SPRINTER Page17
TAKE CARE TO PROTECT CARPETS AND FLOOR in case of leakages. This product is a
machine that contains moving parts which have been greased / lubricated and could leak.
end you constantly lubricate this friction point to prolong the useful
eration. We recommend lubrication of the deck
nths
eavy use (more than 5 hours per week) every 6-8 weeks.
2. and deck evenly (make sure the
.
ly clean it is possible to expect over 1200
ours before additional re-lubing is necessary.
4.4 for proper lubrication:
ion.
ded.
the surface is dry to the touch, apply a suitable silicone lubricant.
4.3 Belt/Deck/Roller Lubrication:
The mat/deck friction may play a major role in the function and life of your treadmill and
that is why we recomm
life of your treadmill.
Lubrication is provided with this unit. You should apply the enclosed lubrication after
approximately the first 50 hours of op
according to the following timetable:
Light use (less that 3 hours per week) every 6 mo
Medium use (3-5 hours a week) every 3 months
H
See below procedures for lubricating:
1. Use a soft, dry cloth to wipe the area between the belt and deck.
Spread lubricant onto the inside surface of belt
machine is turned off and power is disconnected).
3. Periodically lubricate the front and rear rollers to keep them at there peak performance
If the treadmill belt/deck/roller is kept reasonab
h
How to check the running mat
1. Disconnect the main power supply.
2. Fold the treadmill up into the storage posit
3. Feel the back surface of the running mat.
If the surface is slick when touched, then no further lubrication is nee
If

We recommend you use a silicone based spray to lubricate your Lifespan
Treadmill. This Can be purchased from your local sports Retailer or a local
hardware store.
4.5 Belt Adjustment
Belt Tension Adjustment-It is very important for joggers and runners in order to
provide a smooth, steady running surface. Adjustment must be made from the right and
left rear roller in order to adjust tension with the Allen Key provided in the parts package.
The adjustment bolt is located at the end of the rails as noted in diagram below:
Left bolt Right bolt
Note: Adjustment is thru small hold of end cap.
Tighten the rear roller only enough to prevent slippage at the front roller. Turn both the
right and left bolt clockwise one full turn and inspect for proper tension. When an
adjustment is made to the belt tension, you must also make a tracking adjustment to
compensate for the change in belt tension.
DO NOT OVER TIGHTEN - Over tightening will cause belt damage and premature bearing
failure. This may also cause reduced motor performance and excessive roller wear.
NOTE: When properly tightened, the sides of belt can be raised approximate 2-3 inches off
the board.
LIFESPAN SPRINTER Page18

4.6 Belt Tracking Adjustment:
This treadmill is designed to keep the belt reasonably centred while in use. It is normal
for some belts to drift near one side while the belt is running with no one on it. After a
few minutes of use, the belt should have a tendency to centre itself. If during use, the
belt continues to move toward one side, adjustments are necessary. The procedures are
as below:
▲First set speed at approximately 3.5km/h.
▲Second check the belt shifts to which side.
If the belt shifts to right, tighten the right bolt and loosen the left bolt by using
6mm Allen Key, until the belt is centered itself; If belt shifts to left, tighten the left bolt
and loosen the right bolt by using 6mm Allen Key, until the belt is centered. When
adjusting the belt using the 6 mm Allen Key, it is important to adjust the belt in half turn
increments. Over adjusting the belt can cause damage to the mat.
LIFESPAN SPRINTER Page19
If the belts has drifted to the RIGHT If the belts has drifted to the LEFT
错误！未指定主题。 错误！未指定主题。
5 TROUBLE SHOOTING
This treadmill is designed in a way that in the event of an electrical fault, the machine
will turn off automatically to prevent any injuries to the user and to prevent damage to
the machine (i.e. motor).
When the treadmill behaves erratically, simply reset the treadmill by turning the power
switch off, waiting for 1 minute then turning the power button back on.
If, after you have reset the treadmill, it is still not running correctly, please run the self-
checking analyse to distinguish what type of error problem the machine is encountering.
5.1 Troubleshooting Table