Life Span VISION User manual

Product may vary slightly from the item pictured due to model upgrades
Read all instructions carefully before using this product. Retain this owner’s manual for
future reference.
VISION OWNER’S MANUAL

2
VISION
TABLE OF CONTENTS
1. IMPORTANT SAFETY INSTRUCTIONS 3
2. IMPORTANT ELECTRICAL INFORMATION 4
3. IMPORTANT OPERATING INSTRUCTIONS 5
4. ASSEMBLY INSTRUCTIONS 6
5. FOLDING INSTRUCTIONS 9
6. GROUNDING METHODS 10
7. OPERATION GUIDE 11
8. EXERCISE GUIDE 16
9. MAINTENANCE INSTRUCTIONS 18
10. EXPLODED DIAGRAM 22
11. PARTS LIST 23
12. TROUBLE SHOOTING GUIDE 26
13. WARRANTY REGISTRATION 28
14. PROGRAM CHART 29

3
VISION
1. IMPORTANT SAFETY INSTRUCTIONS
WARNING - Read all instructions before using this treadmill.
It is important your treadmill receives regular maintenance to prolong its useful life. Failing to
regularly maintain your treadmill may void your warranty.
Danger –To reduce the risk of electric shock disconnect your treadmill from the electrical outlet prior to
cleaning and/or service work.
DO NOT USE AN EXTENSION CORD: DO NOT ATTEMPT TO DISABLE THE GROUNDED PLUG BY
USING IMPROPER ADAPTERS OR IN ANY WAY MODIFY THE CORD SET.
Install the treadmill on a flat level surface with access to a 220-240 volt (50/60Hz), grounded outlet.
Do not operate treadmill on deeply padded, plush or shag carpet. Damage to both carpet and
treadmill may result.
Do not block the rear of the treadmill. Provide a minimum of 1 metre clearance between the rear of
the treadmill and any fixed object.
Place your unit on a solid, level surface when in use
Never allow children on or near the treadmill.
When running, make sure the plastic clip is fastened on your clothing. It is for your safety, should
you fall or move too far back on the treadmill.
Keep hands away from all moving parts.
Never operate the treadmill if it has a damaged cord or plug.
Keep the cord away from heated surfaces.
Do not operate where aerosol spray products are being used or where oxygen is being administered.
Sparks from the motor may ignite a highly gaseous environment.
Never drop or insert any object into any openings.
The treadmill is intended for in-home use only and not suitable for long time running.

4
VISION
To disconnect, turn all controls to the off position, remove the safety key, and then remove the plug
from the outlet.
The pulse sensors are not medical devices. Various factors, including the user’s movement, may
affect the accuracy of heart rate readings. The pulse sensors are intended only as exercise aids in
determining heart rate trends in general.
Use the handrails provided; they are for your safety.
Wear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for use on your
treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
Allowed temperature: 5 to 40 degrees.
Remove the safety key after use to prevent unauthorized treadmill operation.
2. IMPORTANT ELECTRICAL INFORMATION
WARNING!
NEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill. Route the power
cord away from any moving part of the treadmill including the elevation mechanism and transport
wheels.
NEVER remove any cover without first disconnecting AC power.
NEVER expose this treadmill to rain or moisture. This treadmill is not designed for use outdoors,
near a pool, or in any other high humidity environment.

5
VISION
3. IMPORTANT OPERATING INSTRUCTIONS
Be sure to read the entire manual before operating your machine.
Understand that changes in speed and incline do not occur immediately. Set your desired speed on
the computer console and release the adjustment key. The computer will obey the command
gradually.
Use caution while participating in other activities while walking on your treadmill, such as watching
television, reading, etc. These distractions may cause you to lose balance or stray from walking in
the centre of the belt; which may result in serious injury.
In order to prevent losing balance and suffering unexpected injury, NEVER mount or dismount the
treadmill while the belt is moving. This unit starts with at a very low speed. Simply standing on the
belt during slow acceleration is proper after you have learned to operate this machine.
Always hold on to handrail while making control changes.
A safety key is provided with this machine. Remove the safety key will stop the walking belt
immediately; the treadmill will shut off automatically. Inserting the safety key will reset the display.
Do not use excessive pressure on console control keys. They are precision set to function properly
with little finger pressure.

6
VISION
4. ASSEMBLY INSTRUCTIONS
PART LIST
NO.
DES.
SPEC.
Qty
NO.
DES.
SPEC.
Qty
1
Main
Frame
1
67
Bolt
M8*20
6
12
Allen
Wrench
S=13\14\15
mm
1
70
Bolt
M8*45
2
13
5#Allen
Wrench
5mm
1
77
Screw
ST4.2*19
4
14
6#Allen
Wrench
6mm
1
86
Lock
washer
8
4
31
Right base
cover
1
49
Safety
lock
1
32
Left base
cover
1

7
VISION
STEP 1:
STEP 2:
STEP 3:
1. Open the carton
2. Extract the parts listed above
3. Place the Main Frame (1) onto level
ground
1. Using the Allen Key Wrench (#12),
attach the screw M8*45 (#70) and
Lock Washer (#64) to the base
frame through the base and right
upright tube
2. Repeat for the left upright tube
Note: Support the Uprights with your hands to
prevent them falling down and causing injury.
1. Raise the Computer and Upright tubes in
the direction of the arrows.
Note: Whilst erecting the uprights, make sure the
upright does not press against and damage the
wires inside the upright tubes. Keep holding the
upright and computer by hand so they do not fall
down and cause injury

8
VISION
STEP 4:
STEP 5:
STEP 6:
1. Using the 5# Allen wrench (12), M8*20
screw (67) and lock washer (86) fix the
computer onto each upright.
Note: Support the Computer with your hands to
prevent it falling down and causing injury.
1. Using the #5 Allen wrench (13) and
ST4.2*19 Screw (77), fix the base right
cover (31) onto the right upright and
base.
2. Using the #5 Allen wrench (13) and
ST4.2*19 Screw (77), fix the base left
cover (31) onto the left upright and base.
1. Place the safety key (49) into position on
the computer and start your exercise.

9
VISION
5. FOLDING INSTRUCTIONS
Folding:
Unfolding:
Place your hand on position (A), then pull
up the base frame until you hear the click
sound emitted when the air pressure bar
(B) is locked into the round tube.
Whilst supporting position A with our
hand, gently push the marked area on the
air pressure bar with your foot.
The base frame will descend
automatically. (Please keep people and
any pets away the machine during
descent)

10
VISION
6. GROUNDING METHODS
This product must be grounded. In the event of malfunction or breakdown, grounding reduces the
risk of electric shock. This product is equipped with a cord with an equipment-grounding conductor
and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed
and grounded in accordance with all local codes and ordinances.
DANGER
Improper connection of the equipment-grounding conductor can result in risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the product is properly
grounded.
Do not modify the plug provided with the product –if it will not fit the outlet; have a proper outlet installed by
a qualified electrician.
This product is for use on a nominal 240-volt circuit and has a grounding plug that looks like the plug
illustrated in sketch A in following figure. Ensure the product is connected to an outlet having the same
configuration as the plug. No adapter should be used with this product.