Life Span Workplace DT-3 User manual

DT-3 / DT-5 / DT-7
3

treadmill desk
treadmill desk
treadmill desk
treadmill desk
DT-3 / DT-5 / DT-7
Treadmill Desk

10
11
12
15
16
17
18
19
Welcome
Specications
Warranty
Assembly Instructions (DT-5)
Treadmill to Desktop Assembly (DT-3/DT-5/DT-7)
Desk Leveling and Height Adjustment (DT-5)
Assembly Instructions (DT-7)
Desk Leveling and Height Adjustment (DT-7)
Console Overview (DT-3/DT-5/DT-7)
Innovative Features
Troubleshooting
Engineering Mode

DT-3 DT-5
NA Lifetime
2 Years
1 Year
Bluetooth Yes Yes
Console Only
12.5”W x 3” D x 2” H
NA
NA
NA
NA
Speed Range
Dimensions
Height Adjustment
Desktop Material
Desktop Surface
Max. Load on Desktop
0.4 - 4.0 mph (0.6 - 6.5 kph)
46.5”W x 31” D
36”
to 52”
users 4’10”to 6’8”
1”
Thick HD
Composite Board
Durable Laminate
100 lbs. (45 kg)
2 Year Replacement
NA
0.4 - 4.0 mph (0.6 - 6.5 kph)
U.S. and Canada only
(32cm
W x 7.6cm D x 5.1cm H) (118.1cm
W x 78.7cm D)
(users 147cm to 203cm)
(2.54cm)
(91.4cm to 132.1cm)
DT-3 / DT-5 / DT-7
Treadmill Desk
/DT-7
Height Adjustment Method NA Manual - (DT-5)
Electric - (DT-7)

DT-3/DT-5/DT-7 Treadmill Desks
DT-3
NA
2 Year Replacement
NA
DT-5
Lifetime
2 Years
1 Year
Frame:
Parts:
Labor:
,
Warranty Information
valid in the U.S. and Canada only.
(U.S. and Canada only)
LifeSpan
LifeSpan
LifeSpan
LifeSpan
LifeSpan
LifeSpan
DT-7
Lifetime
2 Years
1 Year
(32 km)

Assembly - (DT-5)
7
DT-5
Treadmill Desk
(preinstalled on D)
Included in Hardware Bag
6

8

Note: If desktop tilts up and
down slightly, re-tighten the
four bolts / nuts inserted in
Step 2C.
DT-5
Treadmill Desk
9
810
9
.

- DT-3/DT-5/DT-7
DT-3 Console
10
E. Install the safety key into the front of the console.
Plug the console connector from the treadmill to the desktop, see illustration below.
For DT-5
For DT-7

Desk Leveling
DT-5
Treadmill Desk
11
The treadmill desk needs to be leveled prior to use.
The desk comes with 2 adjustable feet that can be
used to level the desk and elimate rocking. If the
desk is rocking on two of the feet, adjust the two
front feet until all four feet are sitting securely on

Included in Hardware Bag
Assembly - DT-7
12
5Treadmill Base
M8 Washer
M8 Acorn Nut
Upright Assembly
Desktop
Left Base Foot
Right Base Foot
M4 Screw
M8 * 45L
6
A
D
12
B
4C12 Accessory Tray
Left Upright
Right Upright
Upright Positioning Bumper
Treadmill Positioning Bumpers
Mounting Desktop Brackets
E
E
3
2
8

13
DT-7
Treadmill Desk
Step 1: Upright Support Assembly
A. Position the left base foot (6) so the treadmill
position bumper (C) is facing inward.
B. With the workplace solutions logo facing
towards you, slide the left upright support post
over the bolts installed in the left base foot.
(Nuts and washers pre-installed in base feet)
C. Install the nuts and washers and tighten.
D. Repeat steps A through C for the right base foot
(7) and upright.
Step 2: Accessory Tray Assembly
A. Remove the 4 screws (8) pre-installed in the bottom of the upright assembly crossbar.
B. Line the holes in the accessory tray (12) with the holes in the upright assembly.
C. Install 4 screws and tighten.
12
8
B
A
6
C
7

14
Step 3: Desktop Assembly
A. Remove the Bolts (9), Washers (10)
and Nuts (11) pre-installed in the
upright assembly posts.
B. Hold the desktop over the upright
assembly and place the desk height
control wire harness and the
console wire harness into the
center of the upright assembly (4).
Place the connector ends towards
the center of the tray for easy access
in the next steps of the assembly.
C. Set the desktop down into the
mounting brackets (E) on the
upright posts, align the mounting
holes and re-install the hardware
removed in step A.
D. Tighten the desktop mounting
bolts/nuts.
Step 4: Height Adjustment/Console
Harness Connections
A. Remove the 2 upper screws (13)
attaching the access panel for
the height adjustment control
unit.
B. Tilt down and pull the access
panel out several inches. There
are harnesses pre-attached to
the height controller, so do not
try to fully remove.
Note: It is a good idea to use two people for this part of the assembly in order to
be sure wires are properly routed and do not get pinched while installing desktop.
E
E
9
10
11
Do Not
Remove Screws
13
4

Desk Leveling
DT-7
Treadmill Desk
15
A. To raise the desk press the up or down arrow
until the desktop is at the desired height.
B. To save a height (for an environment with two
users) press the up or down arrows until the
desired height is reached.
C. Press and hold the memory preset 1 or 2 button
for 3 seconds. This will save the current height
into memory.
D. The next time the desk is used simply press the
memory preset that you previously.
Memory
Pre-Sets
Desk
Height
C. Attach the round connector (15) (placed in the
center tray during desktop assembly) to the
height controller port (16).
D. Connect the 7-pin rectangular connectors (14)
(one is placed in the center tray during desktop
assembly and the other is pre-installed at the
factory).
E. Re-attach the access panel to the center tray
and tighten the two screws removed in step A.
Note: Check to be sure all wires are carefully
tucked into the center tray prior to tightening
access panel screws to prevent harness
damage.
Step 4: Height Adjustment/Console Harness Connections Continued
14
15
16
Step 5: Treadmill to Desktop Assembly
The treadmill desk needs to be leveled prior to use.
The desk comes with 2 adjustable feet that can be
used to level the desk and elimate rocking. If the
desk is rocking on two of the feet, adjust the two
front feet until all four feet are sitting securely on
Plug the power cord into the desk recepticle (17)
and into a wall outlet. Plug the console electronics
cord into desk D-connector (18). See instructions
on page 10 for treadmill base connection.
18
17

The Steps are counted normally from 1 to 9999 steps. After 9,999 steps the display format
changes to accommodate more than 4 digits. Take the number shown in the display and add a
zero to the right and that shows the number of steps.
Below are examples of what the display will read and what those numbers mean:
1001 = 10,010 steps
1005 = 10,050 steps
1010 = 10,100 steps
1100 = 11,000 steps
Note:
E
E. Bluetooth -Press to turn on bluetooth to pair with personal computer.
Note: Not all personal computers have a bluetooth module. A bluetooth adaptor can be
purchased to work with your personal computer.
16
1.
2.
3.
4.
5.
Start/ON - If the console is in sleep mode press and hold this button for 3 seconds to turn
the console on. Once the console is turned on press to start the treadmill.

count
Audible Safety Alert - This treadmill has an audible alert to notify the user when the treadmill is starting
as well as when the speed is being adjusted.
Bluetooth - The DT series consoles include a bluetooth module to support LifeSpan apps,
which can be downloaded from the LifeSpan Fitness Club.
Charging Port (DT-3 ONLY) - Used for charging your wireless mobile devices.
17
15
.
feature will also be disabled.
DT-3 / DT-5 / DT-7
Treadmill Desk
(1.6 kph).
For example, the Intelli-Step feature will have a dicult time picking up the steps of a light user
(under 110lbs/50kg) or at speeds lower than 1mph/1.6kph.

18
Problem: Uart shows in diplay.
steps 2D and 3C during assembly. Turn the treadmill power back on and check to see
if it functions.
Problem: dc-6 shows in display.
steps 2D and 3C during assembly. Turn the treadmill power back on and check to see
if it functions.
Problem:
Solution:
Console not connecting to personal computer via Bluetooth.
Log into your LifeSpan Fitness Club account. Go to the Frequently Asked Questions
link located at the bottom of your home page. If further assistance is needed
please email [e-mail].
Only the weight LED is dimly lit.
The treadmill is in sleep mode. Press and hold the on/start button for three
seconds to power on the unit.

reinstall the safty key.
Warning - The audible alert is turned on from the manufacturer to warn the user that
at the sole discretion of the user.
5. F017
19
n
s
(miles)
(kilometers)
DT-3 / DT-5 / DT-7
Treadmill Desk

DT-3 / DT-5 / DT-7