Life Span Equalizer User manual

Product may vary slightly from the item pictured due to model upgrades
USER’S
MANUAL
EQUALIZER

LIFESPAN EQUALIZER Page 1
CONTENTS
1 IMPORTANT SAFETY INSTRUCTIONS ……………………………………………….. 2
1.1 IMPORTANT ELECTRICAL INFORMATION ……………………………………………….. 3
1.2 IMPORTANT OPERATIONAL INSTRUCTIONS ……………………………………………….. 4
1.3 FOLDING INSTRUCTIONS ……………………………………………….. 4
2 ASSEMBLY INSTRUCTIONS ……………………………………………….. 5
3 DISPLAY PANEL OPERATIONS ……………………………………………….. 9
3.1 SAFETY KEY ……………………………………………….. 9
3.2 GETTING STARTED ……………………………………………….. 10
3.3 DISPLAY OPERATION ……………………………………………….. 10
3.4 PULSE GRIP FEATURE ……………………………………………….. 14
3.5 CALORIE DISPLAY ……………………………………………….. 14
3.6 PROGRAMS ……………………………………………….. 14
4 MAINTENANCE ……………………………………………….. 16
4.1 GENERAL CLEANING ……………………………………………….. 16
4.2 GENERAL CARE ……………………………………………….. 16
4.3 BELT/DECK/ROLLER LUBRICATION ……………………………………………….. 17
4.4
HOW TO CHECK THE RUNNING MAT FOR PROPER
LUBRICATION ……………………………………………….. 17
4.5 BELT ADJUSTMENT ……………………………………………….. 18
4.6 BELT TRACKING ADJUSTMENT ……………………………………………….. 19
5 TROUBLESHOOTING ……………………………………………….. 20
5.1 TROUBLESHOOTING TABLE ……………………………………………….. 20
6 EXERCISE GUIDE ……………………………………………….. 22
6.1 WORKOUT GUIDELINES ……………………………………………….. 23
7 WARRANTY REGISTRATION ……………………………………………….. 25
8 EXPLODED DIAGRAM ……………………………………………….. 25
9 PARTS LIST ……………………………………………….. 26

LIFESPAN EQUALIZER Page 2
1. IMPORTANT SAFETY INSTRUCTIONS
Danger–To reduce the risk of electric shock disconnect your treadmill from the
electrical outlet prior to cleaning and/or service work.
DO NOT USE AN EXTENSION CORD: DO NOT ATTEMPT TO DISABLE THE GROUNDED
PLUG BY USING IMPROPER ADAPTERS OR IN ANY WAY MODIFY THE CORD SET.
zInstall the treadmill on a flat level surface with access to a 220-240 volt (50/60Hz),
grounded outlet.
zDo not operate treadmill on deeply padded, plush or shag carpet. Damage to both
carpet and treadmill may result.
zDo not block the rear of the treadmill. Provide a minimum of 1 metre clearance
between the rear of the treadmill and any fixed object.
zPlace your unit on a solid, level surface when in use.
zNever allow children on or near the treadmill.
zWhen running, make sure the plastic clip is fastened on your clothing. It is for your
safety, should you fall or move too far back on the treadmill.
zKeep hands away from all moving parts.
zNever operate the treadmill if it has a damaged cord or plug.
zKeep the cord away from heated surfaces.
zDo not operate where aerosol spray products are being used or where oxygen is
being administered. Sparks from the motor may ignite a highly gaseous environment.
zNever drop or insert any object into any openings.
zThe treadmill is intended for in-home use only and not suitable for long time running.
zTo disconnect, turn all controls to the off position, remove the safety key, and then
remove the plug from the outlet.
WARNING - Read all instructions before using this treadmill.
It is important your treadmill receives regular maintenance to prolong its
useful life. Failing to regularly maintain your treadmill may void your

LIFESPAN EQUALIZER Page 3
zThe pulse sensors are not medical devices. Various factors, including the user’s
movement, may affect the accuracy of heart rate readings. The pulse sensors are
intended only as exercise aids in determining heart rate trends in general.
zUse handrails provided; they are for your safety.
zWear proper shoes. High heels, dress shoes, sandals or bare feet are not suitable for
use on your treadmill. Quality athletic shoes are recommended to avoid leg fatigue.
zAllowed temperature: 5 to 40 degrees.
Remove the safety key after use to prevent unauthorized treadmill operation.
1.1 IMPORTANT ELECTRICAL INFORMATION
WARNING!
zNEVER use a ground fault circuit interrupt (GFCI) wall outlet with this treadmill.
Route the power cord away from any moving part of the treadmill including the
elevation mechanism and transport wheels.
zNEVER remove any cover without first disconnecting AC power.
zNEVER expose this treadmill to rain or moisture. This treadmill is not designed for
use outdoors, near a pool, or in any other high humidity environment.
For your information, please note following electronical specification of Treadmill:
♦Input voltage: ～240V (50HZ)
♦Speed display scope: 1.0-22 (KM/h)
♦Time display scope: 0：00-99：59 (minute: second)
♦Distance display scope: 0.01-99.9 (Km)
♦Heart rate display scope: 60-200 (times/min)
♦Energy display scope: 0-999 (Cal)
♦Gradient display scope: 0-20%

LIFESPAN EQUALIZER Page 4
1.2 IMPORTANT OPERATION INSTRUCTIONS
zBe sure to read the entire manual before operating your machine.
zUnderstand that changes in speed and incline do not occur immediately. Set your
desired speed on the computer console and release the adjustment key. The
computer will obey the command gradually.
zUse caution while participating in other activities while walking on your treadmill;
such as watching television, reading, etc. These distractions may cause you to lose
balance or stray from walking in the centre of the belt; which may result in serious
injury.
zIn order to prevent losing balance and suffering unexpected injury, NEVER mount
or dismount the treadmill while the belt is moving. This unit starts with at a very low
speed. Simply standing on the belt during slow acceleration is proper after you have
learned to operate this machine.
zAlways hold on to handrail while making control changes.
zA safety key is provided with this machine. Remove the safety key will stop the
walking belt immediately; the treadmill will shut off automatically. Insert the safety
key will reset the display.
zDo not use excessive pressure on console control keys. They are precision set to
function properly with little finger pressure.
1.3 FOLDING THE TREADMILL
When folding the treadmill, pull out the handles on the holding spanner and place the
main frame at corresponding position. By then, the handle bolt will appear automatically.
After that, move the treadmill to another place so as to make it occupy a smaller area.
Before the use, place the treadmill to the position you would like to do exercise, and lift
its main frame by right hand and pull out the handles and place them on the floor slowly.
Then the handles will appear automatically. Finally screw down the handles firmly to
release yourself from being worried about the safety during exercise.

LIFESPAN EQUALIZER Page 5
2 ASSEMBLY INSTRUCTIONS
Assembly List: Ⅴ
Ⅰ Ⅱ
Ⅲ
Ⅳ Ⅴ Ⅵ
Ⅶ Ⅷ Ⅸ
Packing List:
No. Title Spec. Qty Remark
ⅠMain frame 1
ⅡLeft pillar handrail
combination 1
ⅢRight pillar handrail
combination 1
ⅣElectronic meter frame 2
ⅤCombination of left and
right handrails 2
ⅥElectronic meter 1
ⅦSeat tube of electronic
meter 1
ⅧCrossed solid wrench S13 S14 S15 1
ⅨInner hexagon spanner S5 S6 2

LIFESPAN EQUALIZER Page 6
Assembly Steps:
1. Take all parts of the running machine out from the packing case.
Figure 3
WE RECOMMEND YOU HAVE SOMEONE TO ASSIST YOU IN LIFTING AND ASSEMBLING
YOUR LIFESPAN TREADMILL. FOLLOW THESE INSTRUCTIONS CAREFULLY AND IT WILL
MAKE IT EASIER TO ASSEMBLE YOUR LIFESPAN TREADMILL
CAUTION:
1. DO NOT PLUG IN POWER CORD UNTIL FINAL ASSEMBLY IS COMPLETED AND
MOTOR COVER IS INSTALLED.
2. Do not attempt to assemble the treadmill until the assembly instructions are
followed and the uprights are attached to the treadmill. Failure to follow this can
result in damage to the treadmill.
3. Your treadmill is a very heavy piece of exercise equipment and should be handled
with caution.
4. Children should not be allowed to play on the treadmill or move the treadmill
deck up and down.

LIFESPAN EQUALIZER Page 7
2. As shown in Figure 3: (1) Put the lower part of left pillar 84 into the pillar seat of base combination 79
first; (2) And then fasten left pillar 84 onto 79 by inner hexagon socket screw 1 and inner dead washer 28
in the way shown in Figure 3 and use S6 inner hexagon socket wrench for tightening; (3) Connect trunk
line 74 with trunk line 75 and then put right pillar 85 into the pillar seat of base combination 79; (4) And
finally fasten the right pillar 85 onto the base combination 79 by inner hexagon socket screw 1, and inner
dead washer 28 in the way shown in Figure 3 and use S6 inner hexagon socket wrench for tightening.
Figure 4
3. As shown in Figure 4: (1) Firstly, cut over hole of electronic meter frame 88 into the double-screw bolt
of electronic meter 66; (2) And then lock inner hexagon socket screw 13 into the screw of electronic
meter 66 respectively; and finally use S6 inner hexagon wrench for tightening.
Figure 5

LIFESPAN EQUALIZER Page 8
4. As shown in Figure 5: (1) Cut over the electronic meter which has been connected well in last step into
the upper parts of left and right pillars respectively; (2) And then connect link trunk line 74 with the
connecting wire of the electronic meter well; (3) And finally lock inner hexagon screw 1 by inner hexagon
socket wrench and then fix it on 84 and 85.
5. As shown in Figure 6: (1) Nest handrails 82 and 83 into electronic meter frame ( lifting at left, speed at
right); (2) And then fasten them onto electronic meter frame by inner hexagon screw 15 and get right the
foam ; (3) And finally fix the lower ends of the handrails onto the pillar by inner hexagon bolt 14.
Figure 7
6. As shown in Figure 7: (1) Nest pull tube 86 into the round tubes of left and right pillars 84 and 85; (2)
And then churn up the external foam of pull tube 86, conduct a locking by cross recessed screw 18 and a
tightening with a crossed solid wrench; (3) And finally knead the foam.
7. Check whether or not all parts have already been firmly locked. The assembly is now completed.

LIFESPAN EQUALIZER Page 9
Caution:
1. Keep the user manual and assembly tools for future servicing or repair.
2. Conduct another check to all connecting parts once assembly is completed to ensure
everything is installed correctly and running smoothly.
3. Make certain there are no factors which will lead to an unstable placement of the
treadmill, such as unlevel ground as it places a hidden safety danger to users.
4. When folding the treadmill, the elastic pin should be pulled out and raised to a certain
height. Moving may be done only after it is confirmed that the elastic pin has already
been inserted into the hole of the extension tube.
Ensure all fixings are tightly secured and the treadmill is well constructed.
3 DISPLAY PANEL OPERATIONS
3.1 Safety Key
IMPORTANT: The treadmill will not operate if the safety key is not in place.

LIFESPAN EQUALIZER Page 10
Before starting the treadmill, attach the magnetic key to the display panel, and then
attach the clip on the other end to your clothing (above the waist). If the safety key is
removed whilst you are operation the treadmill, the machine will turn itself off.
When the treadmill is not in use, you should remove the safety key.
Store the safety key in a safe place OUT OF REACH OF CHILDREN.
3.2 Getting Started
Power the treadmill on by plugging it into an appropriate wall outlet, then turn on the
power switch located at the front of the treadmill below the motor shield. Ensure that
the safety key is installed, as the treadmill will not power on without it.
When the power is turned on, all the lights on the display will light for a short time.
To start the treadmill, please press ‘SPEED +’. You ill hear the sound of the buzzer. To
increase and decrease the speed, you may use either speed up and down buttons or the
quick set buttons 2, 5, 8, 11 and 14. The maximum speed of the treadmill is 22km/h. To
increase and decrease the incline, you may use either incline up and down buttons or
the quick set buttons 3, 6, 9, 12 and 15.
In case of emergency, you may pull out the safety key off and the treadmill will stop
immediately.
When the exercise comes to its end, it is necessary to slow down and press ‘STOP’ to
stop the treadmill at once.
3.3 Display Operation:
Exercise modes: manual, mode, program
Manual exercise mode: it is a motion mode used to set the amount of exercise.
Mode motion mode: it is a motion mode set with given amount of exercise.
A. Time motion mode: it is used to set exercise time, such as 30min.
B. Distance motion mode: it is used to set motion distance, such as 3km.

LIFESPAN EQUALIZER Page 11
C. Calorie exercise mode: it is used to set the amount of calorie one would like to
consume, such as 50 calories.
Program exercise mode: it refers to different exercise plans set in the running machine.
And this running machine is internally set with 24 exercise plans.
Instructions on Display Window:
1. Both runway quantity and program motion map are displayed in the lattice window.
2. Both distance and calorie are displayed in the leftmost window.
3. Both time and incline are displayed in the middle location of window.
8. Both heartbeat and speed are displayed in the rightmost window.
III. Keys
Apart from a mainboard, this product is separately provided with a keyboard with
specific settings as bellow:
1. QUICK INCLINE 5 incline direct selection keys, i.e. 3, 6, 9, 12, and 15 (positioned on
the mainboard)
2. QUICK SPEED 5 speed direct selection keys, i.e. 2, 5, 8, 11, and 14 (positioned on
the mainboard)
3. 3 MP3 control keys (VOLUME sound on/off key; VOLUME sound ‘+’ key, and VOLUME
sound ‘-’ key)
5. 1 Start activate key
6. 1 Stop stop/clearing key
7. SELECT mode/program selection key
8. 1 ‘INCLINE +’ key
9. 1 ‘INCLINE -’ key
10. 1 ‘SPEED +’ key
11. 1 ‘SPEED -’ key
IV. Parameters
1. Mains voltage: 240V
2. Lowest speed: 1.0Km/h

LIFESPAN EQUALIZER Page 12
3. Highest speed: 22Km/h
4. Minimum gradient: 0
5. Maximum gradient: 20
6. Longest exercise time under a manual mode: 99.59min
7. Longest exercise time under a time mode: 99min
8. Shortest exercise time under a time mode: 5min
9. Longest exercise distance under a distance mode: 99Km
10. Shortest exercise distance under a distance mode: 1Km
11. Maximum calorie consumed under a calorie mode: 990 Cal
12. Minimum calorie consumed under a calorie mode: 10 Cal
13. Shortest time under a (P1—P24) program motion: 5min
14. Longest time under a (P1—P24) program motion: 99min
15. Heartbeat times: 60-200
V. Safety
Take off the safety switch under any circumstance, the system will shut down and
simultaneously give out a long sound and display a warning (all windows will display ‘---
’).
VI. Exercise Mode
The exercise modes mentioned here have the common preconditions that the system
has already been electrified normally and that the safety switch has already been placed
correctly.
1. Manual
A. Entry
Press down ‘START’, and the figure in the lattice window will count down from 3 to 1, the
buzzer will give out a prompt sound, and the system will start.
B. Adjustment of Running Machine
Speed may be adjusted through ‘SPEED +’ and ‘SPEED-’, and the incline value may be
adjusted through ‘INCLINE +’ and ‘INCLINE -’.

LIFESPAN EQUALIZER Page 13
C. The running machine will then calculate the exercise parameters and give updating
display in the window. And the lattice will display the runway quantity (400m for one
cycle).
D. Pressing QUICK SPEED may realize a direct speed regulation, and pressing QUICK
INCLINE may realize a direct regulation of the gradient you want.
E. Music may be switched on or off at any time.
F. Press down ‘STOP’, and the system will shut down.
G. Once the exercise time is longer than 100min, the system will shut down.
2. Mode
A. Entry
Press ‘SELECT’, and the given window will give a blinking display to prompt that an entry
into the mode selection among ‘time, distance, and calorie’. After that, a regulation of
amount of exercise may be realized by ‘SPEED +’ or ‘INCLINE +’, and ‘SPEED -’ or
‘INCLINE-’. Press down ‘START’ to enter a given mode for operation, and the system will
start then.
B. Adjustment of Running Machine
Speed may be adjusted through ‘SPEED +’ and ‘SPEED-’, and the incline value may be
adjusted through ‘INCLINE +’ and ‘INCLINE -’.
C. The running machine will then calculate the exercise parameters and give updating
display in the window. And the lattice will display the runway quantity (400m for one
cycle).
D. Press down ‘STOP’, and the system will shut down.
E. Once the amount of exercise exceeds the set value, the system will shut down. At this
time, press ‘STOP’ once, and the system will return to the standby state.
3. Mode
With a scientific arrangement, the system is internally set with 24 exercise modes (see
attached list 1).
A. Entry

LIFESPAN EQUALIZER Page 14
When the system is under a selection state of ‘calorie mode’, press down ‘SELECT’, and
the speed window will display ‘P-X’ and the time window will give a blinking display. At
this time, the ‘Time, Entry’ may be regulated by ‘SPEED +’ or ‘INCLINE +’, and ‘SPEED -’
or ‘INCLINE-’. Press down ‘START’, and the system will start then.
B. Adjustment of Running Machine
Speed may be adjusted through ‘SPEED +’ and ‘SPEED-’, and the incline value may be
adjusted through ‘INCLINE +’ and ‘INCLINE -’.
C. The running machine will then calculate the exercise parameters and give updating
display in the window. And the lattice will display the runway quantity (400m for one
cycle).
D. Press down ‘STOP’, and the system will shut down.
E. Once the program is finished, the system will shut down. At this time, press ‘STOP’
once, and the system will return to the standby state.
3.4 Pulse Grip Feature:
If the computer detects a pulse signal, the PULSE window will show your heart rate beat
per minute instead of “P”. You must use both stainless steel sensors to display your
pulse. Pulse value displays anytime the upper display is receiving a Grip Pulse signal.
3.5 Calorie Display:
Displays the cumulative calories burned at any given time during your workout.
Note: This is only a rough guide used for comparison of different exercise
Sessions, which cannot be used for medical purposes.
3.6 Programs:
Set time/16 time period = the operation time of former and later time periodTime
Slice
Program
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Speed 3 3 4 4 5 5 7 7 6 6 5 5 4 4 3 3P1
Gradient 2 2 6 6 3 3 5 5 4 4 3 3 2 2 1 1
Speed 2 4 6 6 7 8 4 4 7 8 8 6 8 5 5 3P2
Gradient 1 1 2 2 5 5 4 4 6 6 3 3 2 2 1 1

LIFESPAN EQUALIZER Page 15
Speed 4 4 6 7 8 8 7 7 9 9 6 10 7 6 6 2
P3
Gradient 2 6 8 10 12 12 12 8 8 7 10 10 6 4 2 2
Speed 4 6 3 7 2 5 8 10 6 12 8 10 7 5 3 2P4
Gradient 4 4 10 5 11 11 6 8 10 5 6 4 4 3 1 0
Speed 5 6 6 8 9 10 10 11 12 12 10 8 12 10 7 5P5
Gradient 4 4 6 8 10 12 6 5 5 10 10 7 5 3 2 0
Speed 3 6 9 12 10 8 7 7 8 10 9 10 12 11 6 4P6
Gradient 1 2 3 3 4 4 5 5 0 0 2 2 3 4 4 1
Speed 6 7 8 10 12 10 8 7 8 10 11 11 10 8 6 5P7
Gradient 3 3 4 4 3 3 2 2 5 5 6 6 4 2 2 0
Speed 6 6 10 10 12 10 8 8 10 8 6 8 12 12 6 3P8
Gradient 4 4 5 5 3 3 6 6 2 2 4 4 3 2 2 0
Speed 1 4 6 8 10 8 6 4 2 2 1 4 6 8 6 4P9
Gradient 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
Speed 1 2 6 6 8 10 6 6 2 2 1 2 6 6 8 4P10
Gradient 1 2 1 2 1 2 1 1 2 0 1 2 1 2 1 2
Speed 1 3 4 5 2 3 4 5 3 2 1 3 4 5 2 3P11
Gradient 1 1 2 3 4 4 3 2 1 0 1 1 2 3 4 4
Speed 1 4 6 2 4 6 2 4 6 2 1 4 6 2 4 6P12
Gradient 1 3 5 7 9 11 9 7 5 3 1 3 5 7 8 11
Speed 2 3 4 5 6 5 4 3 2 1 2 3 4 5 6 5P13
Gradient 2 6 6 8 10 8 6 6 2 2 2 6 6 8 10 8
Speed 2 4 6 8 6 6 4 4 2 2 2 4 6 8 6 6P14
Gradient 2 3 4 5 2 3 4 5 4 3 2 3 4 5 2 3
Speed 2 1 6 8 10 8 6 4 2 2 2 4 6 8 10 8P15
Gradient 2 1 6 2 4 6 2 4 6 2 2 4 6 2 4 6
Speed 2 2 6 6 8 10 6 6 2 2 2 2 6 6 8 10P16
Gradient 1 3 1 2 1 2 1 1 2 0 1 3 1 2 1 2
Speed 2 3 4 5 3 4 5 3 2 2 3 4 5 2 3 4P17
Gradient 1 2 2 3 4 4 3 2 1 0 1 2 2 3 4 2
Speed 2 4 6 2 4 6 2 4 6 2 2 4 6 2 4 6P18
Gradient 1 3 5 7 9 11 9 7 5 3 1 4 5 7 9 5
Speed 1 3 4 5 6 5 4 3 2 1 1 3 4 5 6 5P19
Gradient 2 5 6 8 10 8 6 6 2 2 2 5 6 8 10 8
Speed 1 4 6 8 6 6 4 4 2 2 1 4 6 8 6 6P20
Gradient 2 4 4 5 2 3 4 5 4 3 2 4 4 5 2 3
Speed 1 4 6 8 10 8 6 4 2 2 2 4 6 8 10 8P21
Gradient 2 3 6 2 4 6 2 4 6 2 2 3 6 2 4 6
Speed 2 3 3 6 7 7 4 6 2 2 3 6 2 4 6 2P22
Gradient 4 5 5 5 6 6 6 7 4 6 7 4 4 4 2 2
Speed 2 4 4 7 7 4 7 8 4 8 9 9 4 4 4 5P23
Gradient 5 5 5 6 6 6 4 4 6 6 5 5 8 8 9 9
Speed 2 4 5 6 7 5 4 6 8 8 6 6 5 4 4 2P24
Gradient 5 6 6 6 7 5 8 8 4 4 4 5 5 8 8 10

LIFESPAN EQUALIZER Page 16
4 MAINTENANCE
Reasonable cleaning/lubricating should be made to extend the life time of this unit.
Performance is maximized when the belt and mat are kept as clean as possible.
WARNING: THE MAT/DECK FRICTION MAY PLAY A MAJOR ROLE IN THE
FUNCTION AND LIFE OF YOUR TREADMILL AND THAT IS WHY WE RECOMMEND
YOU CONSTANTLY LUBRICATE THIS FRICTION POINT TO PROLONG THE USEFUL
LIFE OF YOUR TREADMILL. FAILING TO DO THIS MAY VOID YOUR WARRANTY.
WARNING: UNPLUG POWER CORD BEFORE MAINTENANCE.
WARNING: STOP TREADMILL BEFORE FOLDING.
4.1 General Cleaning
zUse a soft, damp cloth to wipe the edge of the belt and the area between the belt
edge and frame. A mild soap and water solution along with a nylon scrub brush will
clean the top of the textured belt. This task should be done once a month. Allow to
dry before using.
zOn a monthly basis, vacuum underneath your treadmill to prevent dust build up.
Once a year, you should remove the black motor shield and vacuum out dirt that
may accumulate.
4.2 General Care
•Check parts for wear before use.
•Pay particular attention to the fixing knobs and make sure they are tight.
•Always replace the mat if worn and any other defective parts.
•If in doubt do not use the treadmill and contact our helpline.

LIFESPAN EQUALIZER Page 17
TAKE CARE TO PROTECT CARPETS AND FLOOR in case of leakages. This product is a
machine that contains moving parts which have been greased / lubricated and could
leak.
4.3 Belt/Deck/Roller Lubrication:
The mat/deck friction may play a major role in the function and life of your treadmill and
that is why we recommend you constantly lubricate this friction point to prolong the
useful life of your treadmill.
Lubrication is provided with this unit. You should apply the enclosed lubrication after
approximately the first 50 hours of operation. We recommend lubrication of the deck
according to the following timetable:
Light use (less that 3 hours per week) every 6 months
Medium use (3-5 hours a week) every 3 months
Heavy use (more than 5 hours per week) every 6-8 weeks.
See below procedures for lubricating:
1. Use a soft, dry cloth to wipe the area between the belt and deck.
2. Spread lubricant onto the inside surface of belt and deck evenly (make sure the
machine is turned off and power is disconnected).
3. Periodically lubricate the front and rear rollers to keep them at there peak
performance.
If the treadmill belt/deck/roller is kept reasonably clean it is possible to expect over
1200 hours before additional re-lubing is necessary.
4.4 How to check the running mat for proper lubrication:
1. Disconnect the main power supply.
2. Fold the treadmill up into the storage position.
3. Feel the back surface of the running mat.
If the surface is slick when touched, then no further lubrication is needed.
If the surface is dry to the touch, apply a suitable silicone lubricant.

LIFESPAN EQUALIZER Page 18
We recommend you use a silicone based spray to lubricate your Lifespan
Treadmill. This Can be purchased from your local sports Retailer or a local
hardware store.
4.5 Belt Adjustment
Belt Tension Adjustment-It is very important for joggers and runners in order to
provide a smooth, steady running surface. Adjustment must be made from the right and
left rear roller in order to adjust tension with the Allen Key provided in the parts package.
The adjustment bolt is located at the end of the rails as noted in diagram below:
Note: Adjustment is thru small hold of end cap.
Tighten the rear roller only enough to prevent slippage at the front roller. Turn both the
right and left bolt clockwise one full turn and inspect for proper tension. When an
adjustment is made to the belt tension, you must also make a tracking adjustment to
compensate for the change in belt tension.
DO NOT OVER TIGHTEN - Over tightening will cause belt damage and premature bearing
failure. This may also cause reduced motor performance and excessive roller wear.
NOTE: When properly tightened, the sides of belt can be raised approximate 2-3 inches
off the board.
Left bolt Right bolt

LIFESPAN EQUALIZER Page 19
4.6 Belt Tracking Adjustment:
This treadmill is designed to keep the belt reasonably centred while in use. It is normal
for some belts to drift near one side while the belt is running with no one on it. After a
few minutes of use, the belt should have a tendency to centre itself. If during use, the
belt continues to move toward one side, adjustments are necessary. The procedures
are as below:
▲First set speed at approximately 3.5km/h.
▲Second check the belt shifts to which side.
If the belt shifts to right, tighten the right bolt and loosen the left bolt by using
6mm Allen Key, until the belt is centered itself; If belt shifts to left, tighten the left bolt
and loosen the right bolt by using 6mm Allen Key, until the belt is centered. When
adjusting the belt using the 6 mm Allen Key, it is important to adjust the belt in half
turn increments. Over adjusting the belt can cause damage to the mat.
If the belts has drifted to the RIGHT If the belts has drifted to the LEFT