Lift Tech Marine AC REMOTE GEN 2 User manual

Operating the AC Motor:
When the lift is going “up” the gear head should be going clockwise. When the lift is going
“down” the gear head should be going counterclockwise. If it’s the opposite direction this
means your lift was let down too far and is backwound. To fix this, let the lift down, when it
runs out of cable it will wind itself up correctly and start going up.
Control Panel:
The control panel works the same as the remote controls. Press UP to go up and DN
to go down. Press the light button to turn the canopy light on or off. When plugged into
power the READY light will be a solid green and the Bluetooth symbol will blink blue. When
you pair a phone through bluetooth the light will be a solid blue and no longer flash. The
STATUS light will turn solid red when any button is pushed. If the remotes work and the
control panel doesnt or vise versa, unplug the unit from power for 2 minutes. Hold the lock/
unlock button until the LED lights start to blink together. When the control panel is locked
the lights will blink for a set amount of time and then go out. To unlock the control panel
Hold the lock/unlock button until the LED lights stop blinking. The Bluetooth App will still
work when the control panel is locked. The control panel and the remote controls will not
work when locked. If the control panel is locked the lights will flash when you press any
button.
Remotes and Bluetooth:
The two blue remote controls that come with the unit are already paired. You can download
the phone app and control your motor with your phone. See the included Bluetooth
instructions.
Off-Season Storage:
We recommend our storage cover for your motor if you are going to leave it sit outside
during the winter months. Our storage cover will breath and let moisture out while your not
using your motor.
Power Outage:
In case of a power outage, use the provided back up bit (inside floatie) on the end of the
shaft with your drill. Visit our website to watch a video on how to use the back up bit.
Power Requirements for AC:
All power used on your dock or lift needs to be GFI Protected at the shoreline.
Extension Cords must be 12/3 and under 150 feet. Circuit Breaker 20 AMPS GFI.
Always disconnect power when lift is left unattended.
Maintenance:
Our motors are self-lubricating and do not need any maintenance.
Canopy Lights:
We offer Canopy lights that can plug into your unit and are controlled by the remotes.
If you use a different brand of canopy lights they might not work. Our canopy lights will
automatically shut off at 7 minutes.
Website:
Go to www.lifttechmarine.com for more information, troubleshooting and how to videos.
We would like to take this opportunity to say thank you. We value you, as a
customer. Should you ever have an issue please give us a call at 218-454-0682 or
send us an email at [email protected]

CONNECTING
TO ANDROID BY
BLUETOOTH
5. Press on the Lift - Signal Strength that comes up
on the phone to pair it.
6. Once the phone is paired it will look like PIC 3.
You are now done pairing your phone with the
control panel. If you want to rename your lift simply
press the rename tab on the top right of the app
and a box will come up like in PIC 4. Rename it to
what you want and hit Rename to save it.
7. UP..... Pressing and holding this button will raise the lift.
DOWN....Pressing and holding this button will lower the lift.
LIGHT..... Pressing this button will turn your canopy light on or off.
LOCK/UNLOCK..... Hold button until the lights start flashing to lock the control
panel and remote controls. If locked hold until lights stop flashing to unlock.
*If your neighbors have a Lift Tech Marine unit make sure they are not using
their lift while you are programming.*
1. Go to Google Play and search for Lift Tech Marine and download the app.
Once installed open the app.
2. To activate the Bluetooth pairing sequence hold the UP and DN buttons on
the control panel at the same time until the blue LED light turns solid. (See
picture below).You will have around 15 seconds to add your phone. If the
blue LED starts to blink, repeat the steps.
3. Press the scan button on the top right of your phone. (See PIC 1)
4. When the phone finds the motor it will look like PIC 2.
PIC 1 PIC 2 PIC 3 PIC 4

CONNECTING
TO IPHONE BY
BLUETOOTH
3. After you have activated the bluetooth sequence
look at your phone and Tap the button in
the upper right hand corner of app. (See pic 2)
LiftTech should now appear like in (pic 3). Tap on
the Lift Tech Signal Strength and the screen should
now look like (pic 4). Now tap on the pair option.
4. Once paired and connected to a Lift Tech
receiver, the screen similar to (pic 5) will show the
remote control options.
5. To rename your lift tap on Rename in the top
right corner of the phone app.
6. UP..... Pressing and holding this button will raise the lift.
DOWN....Pressing and holding this button will lower the lift.
LIGHT..... Pressing this button will turn your canopy light on or off.
LOCK/UNLOCK..... Hold button until the lights start flashing to lock the
control panel and remote controls. If locked hold until lights stop flashing to
unlock.
Tap <disconnect in the upper left corner to save battery life on phone.
*If your neighbors have a Lift Tech Marine unit make sure they are not using
their lift while you are programming.* The app will not work if the Iphone has
Dark Mode enabled.
1. Go to the App store and search for Lift Tech and download the app. Once the
app is downloaded on your phone, open the app and continue.
2. To activate the Bluetooth pairing sequence hold the UP and DN buttons on
the control panel at the same time until the blue LED light turns solid. (See
picture below).You will have around 15 seconds to add your phone. If the blue
LED starts to blink, repeat the steps.

SEND THIS FORM AND YOUR RECEIPT TO :
CUST[email protected]
OR MAIL TO:
LIFT TECH MARINE
7958 HASTINGS ROAD
BAXTER, MN 56425
Warranty Card
*ALL WARRANTY CARDS MUST BE FILLED OUT WITHIN THE TIME FRAME AND HAVE A COPY OF
THE ORIGINAL PURCHASE RECEIPT TO BE VALID.
CIRCLE PRODUCT PURCHASED: AC IS PLUGGED IN TO EXTENSION CORD - DC IS BATTERY POWER.
AC-PWC KIT DC-PWC KIT AC-WHEEL DRIVE DC-WHEEL DRIVE
AC MANUAL DC MANUAL AC REMOTE DC REMOTE AC AUTOSTOP DC AUTOSTOP
WINCHBOX WITH MOTOR
SERIAL # LOCATED ON BACK OF MOTOR CYLINDER: ___________________________
PURCHASED FROM:____________________________________________________
NAME: _____________________________________________________________
ADDRESS: __________________________________________________________
EMAIL:______________________________ PHONE:_________________________
LIFT TECH MARINE WARRANTS OUR MOTOR FROM DEFECTS IN MATERIALS AND
WORKMANSHIP UNDER NORMAL USE FOR A PERIOD OF 2 YEARS FROM THE DATE OF
PURCHASE. DURING THE WARRANTY PERIOD, LIFT TECH MARINE WILL REPAIR THE MOTOR
IF DEFECTIVE. THE WARRANTY IS LIMITED TO THE PURCHASER AND IS NOT TRANSFERABLE.
WARRANTY IS VOID IF THE PRODUCT IS MODIFIED OR ALTERED BY ANYONE OTHER THAN LIFT
TECH MARINE, LLC.
*BLUE REMOTES HAVE A 1 YEAR WARRANTY AND DOESN’T INCLUDE BATTERIES.
FIND MORE INFROMATION ONLINE AT WWW.LIFTTECHMARINE.COM
*Must be filled out and sent to us
within 60 days of purchase along
with a copy of the original receipt
for warranty to be valid.