Lightmybricks LEGO Kessel Run Millennium Falcon 75212 User manual

Light My Bricks
Installation Instructions for Light My Bricks LED Lighting Kits
May 21 · 24 min read
Light My Bricks: LEGO Kessel Run
Millennium Falcon 75212 Lighting Kit
The following page is instructions for the Light My Bricks LEGO Kessel
Run Millennium Falcon (75212) LED lighting kit. You purchase this kit on our
o cial website.
. . .

Package Contents:
• 6x White 15cm Bit Lights
• 3x Flashing White 15cm Bit Lights
• 2x Red 30cm Bit Lights
• 1x Blue 30cm Bit Lights
• 5x White Strip Lights
• 1x Multi E ects Board
• 1x Flicker E ects Board
• 2x 6-Port Expansion Boards
• 1x 30cm Connecting Cable
• 2x 15cm Connecting Cables
• 4x 5cm Connecting Cables
• 1x AA Battery Pack (requires 3x AA Batteries)
• 1x Flat Battery Pack (requires 2x CR2032 Batteries)
LEGO Pieces:
• 2x Trans Light Blue Round Plate 1x1
• 1x Trans Clear Round Plate 1x1
. . .
Important things to note:
Laying cables in between and underneath bricks
Cables can t in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT
forcefully join LEGO® together around cables; instead ensure they are
laying comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a
cable can result in damaging the cable and
light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing
up, look for the soldered “=” symbol on the left side of the port. The
connector side with the wires exposed should be facing toward the
soldered “=” symbol as you insert into the port. If a plug won’t t easily into
a port connector, do not force it.

Incorrectly inserting the connector can can
result in bent pins inside the port or possible
overheating of the expansion board when
connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up,
ensure the side of the connector with the wires exposed is facing down. If a
plug won’t t easily into a port connector, don’t force it.
Doing so will damage the plug and the connector.

Installing Bit Lights under LEGO® bricks and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place
them directly on top of LEGO® studs or in between.
. . .
OK, Let’s Begin!
Lighting the Escape Pod
1.) The rst section we will light up will be the escape pod. To
start,disconnect this from the main ship and then disconnect the
following pieces from the front left.

Disconnect the 1x2 technic brick and then disconnect the trans-light blue
tile from the back of it.

2.) Take a White 15cm Bit Light and then thread the connector side
through the blue technic pin. Thread it all the way through until the Bit
Light is right up against the technic pin, then bend the Bit Light slightly
so that it sits at.
Secure the Bit Light in place by connecting a provided LEGO Trans Light Blue
plate 1x1 over the top.

3.) Reconnect the 1x2 Technic brick back to the escape pod and
thenreconnect pieces we removed earlier.

4.) Repeat previous steps to install another White 15cm Bit Light to the
right side of the escape pod.

5.) Take a 6-Port Expansion Board and connect both bit lights to the
available ports.