Lightmybricks LEGO Super Star Destroyer 10221 Lighting Kit User manual

Light My Bricks
Installation Instructions for Light My Bricks LED Lighting Kits
Sep 14 · 34 min read · Unlisted
Light My Bricks: LEGO Super Star
Destroyer 10221 Lighting Kit
The following page is the instructions for the Light My Bricks LEGO Super
Star Destroyer (10221) LED light kit.
To ensure a trouble-free installation of your light kit, please read and
follow each step carefully.
Please note: This page lists instructions for the
LED light kit only. If you are wishing to purchase
the Light My Bricks LEGO Super Star Destroyer
(10221) LED light kit , please click here to view
the product page
. . .

Package Contents:
• 1x White Strip Light
• 8x Blue Strip Lights
• 13x White 30cm Bit Lights
• 14x Blue 30cm Bit Lights
• 4x Cool White 30cm Bit Lights
• 1x 6-Port Expansion Board
• 2x 8-Port Expansion Boards
• 2x 12-Port Expansion Boards
• 1x Multi E ects Board
• 2x 5cm Connecting Cables
• 11x 15cm Connecting Cables
• 1x 50cm Connecting Cable
• 1x AA Battery Pack (requires 3x AA Batteries)
LEGO Pieces:
• 6x Plate 1x6 (any colour)
• 14x Trans Clear Plate 1x1
• 2x Trans Clear Round Plate 1x1
. . .
Important things to note:
Laying cables in between and underneath bricks
Cables can t in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT
forcefully join LEGO® together around cables; instead ensure they are
laying comfortably in between each stud.

CAUTION: Forcing LEGO® to connect over a
cable can result in damaging the cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board
facing up, look for the soldered “=” symbol on the left side of the port.
The connector side with the wires exposed should be facing toward the
soldered “=” symbol as you insert into the port. If a plug won’t t easily
into a port connector, do not force it.

Incorrectly inserting the connector can can
result in bent pins inside the port or possible
overheating of the expansion board when
connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up,
ensure the side of the connector with the wires exposed is facing down. If
a plug won’t t easily into a port connector, don’t force it. Doing so will
damage the plug and the connector.
Installing Bit Lights under LEGO® bricks and plates.

When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place
them directly on top of LEGO® studs or in between.
. . .
OK, Let’s Begin!
. . .
1.) Start by disconnecting the two long roof sections that run along each side of the
Star Destroyer

Turn the ship around so we can access the back, then disconnect the
centre jet section followed by the two side jet sections.

2.) Take the centre jet section and follow the images below to disconnect sections
so that we can disconnect the jets.

3.) Follow the below images to disassemble the jet section
4.) Take a the left jet and then turn it over so we can access the back.
Take a White 30cm Bit Light and thread it down one of the bottom
holes and then out to the right.

Thread the Bit Light all the way through and then bend it slightly toward
the centre in between the four holes. Secure the Bit Light in place by
reconnecting the trans orange piece over the top.