Lightmybricks LEGO 1989 Batmobile User manual

The following page is the instructions for the Light My Bricks LEGO 1989
Batmobile (76139) LED light kit.
If you run into any issues, please refer to the online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO 1989 Batmobile (76139) LED light
kit , please click here to view the product page
LIGHT MY BRICKS: LEGO 1989 Batmobile 76139
Lighting Kit

Package Contents:
8x White 15cm Bit Lights
6x Warm White 30cm Large Bit Lights
2x Cool White 30cm Bit Lights
4x Red 30cm Bit Lights
1x Rotating White 30cm Bit Light
1x White Strip Light
1x Flicker Effects Board
1x Gun Effects Board
1x NC Push Board
1x 6-Port Expansion Board
2x 8-Port Expansion Boards
1x 12-Port Expansion Board
3x 5cm Connecting Cables
3x 15cm Connecting Cables
1x 50cm Connecting Cable
8x Adhesive Squares
1x AA Battery Pack
LEGO Pieces:
2x Black Round Plate 1×1 with open stud
Important things to note:

Laying cables in between and underneath bricks
Cables can fit in between and underneath LEGO® bricks, plates, and tiles
providing they are laid correctly between the LEGO® studs. Do NOT forcefully
join LEGO® together around cables; instead ensure they are laying comfortably
in between each stud.
CAUTION: Forcing LEGO® to connect over a cable can result in damaging the
cable and light.
Connecting cable connectors to Expansion Boards
Take extra care when inserting connectors to ports of Expansion Boards.
Connectors can be inserted only one way. With the expansion board facing up,
look for the soldered “=” symbol on the left side of the port. The connector side
with the wires exposed should be facing toward the soldered “=” symbol as you
insert into the port. If a plug won’t fit easily into a port connector, do not force it.

Incorrectly inserting the connector can can result in bent pins inside the port
or possible overheating of the expansion board when connected.
Connecting cable connectors to Strip Lights
Take extra care when inserting connectors to ports on the Strip Lights.
Connectors can be inserted only one way. With the Strip Light facing up, ensure
the side of the connector with the wires exposed is facing down. If a plug won’t
fit easily into a port connector, don’t force it. Doing so will damage the plug and
the connector.

Connecting Micro Cable connectors to Micro
Expansion Board Ports
Take extra care when inserting the micro connectors to micro ports of Micro
Expansion Boards. Connecting Micro Bit Lights to Micro Expansion Boards is
similar to connecting lights and cables to Strip Lights. With the expansion
board facing up, ensure the side of the connector with the wires exposed is
facing down. If a plug won’t fit easily into a port connector, do not force it. Use
your fingernail to push the plastic part of the connector to the micro port.
Installing Bit Lights under LEGO® bricks
and plates.
When installing Bit Lights under LEGO® pieces, ensure they are placed the
correct way up (Yellow LED component exposed). You can either place them
directly on top of LEGO® studs or in between.

OK, Let’s Begin!
1.) We will first install the headlights to the batmobile. Carefully remove the two
headlight sections, then flip them over and disassemble the right headlight
section as shown below.

Take a Warm White 30cm Large Bit Light and with the LED facing the
opposite side to the sticker, place it inside the trans yellow brick. Bring the cable
down the side where the sticker is, then secure the Bit Light in place by
reconnecting the trans yellow plate over the top.

Repeat this step to install another 2x Warm White 30cm Large Bit Lights to
the other two headlight pieces, then reconnect each one to the right headlight
ensuring the LEDS are facing to the front.
2.) Bring the ends of the three bit light cables together and thread them
through the space behind the headlights. Turn the batmobile onto it’s left side
so we can access underneath. Find the three cables we threaded through
behind the headlight and pull them all the way out at the front of the wheel.

Turn the vehicle back over and reconnect the right headlight ensuring the
cables underneath are laid in between studs.