Lightolier RADIANCE STEM EXTENSION KITS Guide

T
READANDUNDERSTANDTHESEINSTRUCTIONSBEFOREINSTALLINGFIXTURE lNSTRUCTION SHEET NO,
hisfktureisintendedfor installation in ectordanse with the National Eladricd Code end Id rsgulatbna,
osssurs full sompfianca with Ixal OxJes snd rsgule.tkma,c+@ with your Ixd e!ectriral ins@or Lwfora
wtallation. To prevent eleotrfd sheck, turn off elacbiciy at fuss box before premsding. IS:40719
Retsintheseinstructionsformaintenancereferenoe. Pegelofl
INSTRUCTIONS FOR INSTALLATION AND ASSEMBLY OF
RADIANCE STEM EXTENSION KITS
CAUTION: BE CAREFUL WHILE HANDLING FIXTURE WIRES. DO NOT DAMAGE WIRE INSULATION
OR PINCH WIRES BETWEEN PARTS.
1. Unps& CENTER STEMASSEMBLY (supplisd with f~re) snd cmefuliy until FIXTURE WIRES.
2. Gent~ pull downward en CANOPY to disengege fmm CROSSBAR SPRING CLIPS and expmw CROSSBAR (fig, 1),
3. Remove the two SCREWS from beth sides dSWIVEL CASTING snd skfe SWIVEL PIN oul fmm one d the holse in the SWIVEL CASTING (Fig, 1).
NOTE Asmall smswddver may be required to push SWIVEL PINoutthroughtie hobinSWIVELCASTING,
CAUTION: PLACE SCREWS AND SWIVEL PIN IN ASAFE PLACE; THESE PARTS ARE NEEDED FOR FINAL
ASSEMBLY OF EXTENSION KIT.
4. While holding CENTER STEM ASSEMBLYsnd FIX7UREWIRES, genttfslikieSWlVELCASTlNGfCRQ3SsARAs3EMBLYup FIXTURE WIRES UnfiIA~EMBLY
ISmmpletely rsmoved fmm FIXTURE WIRES (Fig. 2), Plain SWIVEL CASTING/CROSSBAR ASSEMBLY ins safe place.
NOTE Make owtsin QUICK CONNECTORS at the lower endofCENTERSTEMAS3EMSLYdonotslideupinsideSTEM,
=,
FIXTUREWIRES CROSSBAR FIXTUREWIRES
(UN.COILED) CROSSBAR
SWIVELCASTING SPRINGCLIPS
7
ZSP’N SWIVELCASTING[
CENTERSTEMASSEMBLY
SCREWS CROSSBARASSEMBLY [SUPPLIEDWITHFIXNREI
I
CENTERSTEM
CANOPY ASSEMBLY
FIG,1FI
5. Pass FIXTURE WIRES through EXTENSION STEM COLIAR and EXTENSION STEM and slide EXTENSION STEM dewn FIXTURE WIRES until
EXTENSION STEM COL~R meets CENTER STEM AssEMSLY (Fig. 3A),
6. Aligning the holes in the side of CENTER STEM ASSEMBLY WW tie UWSSCIWh~l~ in EXTENSION STEM COLIAR, SIIW COMR to side in~~e
CENTER STEM ASSEMBLY and secure in place by installing the two screws providwJ whh EX7ENSION STEM KIT (fig, 3S),
NOTE Before preceedin~ repeat steps 5snd 6fassmnd EXTENSION STEM KIT is to bused,
7. Re.sssemble SWIVEL CASTING/CROSSBAR ASSEMSLY te the end of WENSION STEM by reveming steps 3snd 4above (Fig. 4),
8. Continue FIXTURE insfsllation by following instructions supplisd with FIXTURE,
NOTE FIXTURES are supplied with enough FIXTURE WIRE 10allow two EXTENSION STEM KITS to be insfsllsd. If only one EXTENSION KIT is uset
excass FIXTURE WIRES should be cut off making certain Mere is aminimum of 6’ of FIXTURE WIRE sbeve CROSSBAR ASSEMSLY for OUTLET BOX WIRING,
‘:’: 4=-:s::
1.1<> l-l-i-c>1.1E la”%R%,gwywu’
—