BDI OLIS 9650 User manual

1
Product Registration
Registering your new BDI product allows us to send you important
product updates, service information and helpful hints related to your
BDI products. Register today, and you will be entered to win free a
BINK table from BDI: www.bdiusa.com/register
Placement and Maintenance
Your Olis Console is designed for indoor use on level floors.
Clean wood veneer and steel parts with a moist cloth.
Olis is engineered for easy assembly. Carefully follow this procedure
to prevent any damage. Do not use power tools for assembly of this
product.
Step 1
Unpack and identify the parts listed below. The assembly workspace
should be a non-marring surface such as carpet. For missing
hardware pieces, contact BDI Customer Service at:
[email protected].
For all other concerns, please contact your BDI retailer.
bdiusa.com
customerservic[email protected]om
Designed by BDI Studio.
These distinctive product configurations are protected by US and international patents, trade dress, and/or
copyright laws. Olis & BDI are trademarks of Becker Designed, Inc. All rights reserved. ©2017, BDI
Made in China. 08.08.2017 V1
OLIS™9650
2 DOOR CONSOLE
C1 Cross Bar x 1
T2 Hex Wrench x 1
H3 #6 x 5/8" Flathead
Wood Screw x 4
H2 1/4-20 x 15 mm
Machine Screw x 10
T1 Phillips Screwdriver x 1
A1 Cabinet x 1
C3 Curved Back Panels x 2
C4 Left Door
Pull x 1
C5 Right Door Pull x 1
C2 Leg Frame x 2
H1 1/4-20 x 25 mm FH
Machine Screw x 4

bdiusa.com
customerservic[email protected]om
OLIS 9650
2 DOOR CONSOLE
2
Step 2 - Attach the 2leg frames C2 to cross bar C1 with 4screws H1 using hex wrench T2.
Make sure all tabs face downward.
Step 3 - With help from another person, carefully position the cabinet A1 upside-down (as shown) or on its
back. Attach the base to the cabinet with 10 screws H2 using hex wrench T2. Do NOT fully tighten until all 10
screws are started.
H2 x 10
2 Person Ta sk
T2
H1
T2
C1
C2
C2
All tabs face down

bdiusa.com
customerservic[email protected]om
OLIS 9650
2 DOOR CONSOLE
3
Step 4 - With help from another person, carefully rotate your Olis Console onto its feet. Partially open left door
and install left door pull C4 using wood screws H3 and Phillip's screw driver T1. Make sure finger scoop is
facing down. Repeat with right door pull C5.
2 Person Ta sk
H3
T1
C4
H3 H3
Step 5 - The 2 curved back panels C3 are removable and can slide towards the middle if one panel is
removed. To remove lift up and pull the bottom edge out of its groove. To re-install, put the top edge of the
back panel into the top groove, then drop the bottom edge into the bottom groove.
2
C3
C3
1

bdiusa.com
customerservic[email protected]om
OLIS 9650
2 DOOR CONSOLE
4
Fine tuning your new BDI Media Furniture
These steps are to be followed after you have unpacked and completed the simple assembly instructions for
your console. Due to jostling in freight or perhaps an uneven floor, the doors on your cabinet may not appear
to be in perfect alignment. Making a few minor adjustments can rectify this situation. The high-quality European
hinge hardware is adjustable. Through a little adjustment, you can modify the orientation of the cabinet doors to
make sure that they are sitting perfectly on your unit.
STEP 1 - Level your unit
Levelers are integrated into each leg assembly and are accessed at the bottom of each cabinet leg. If your floor
is uneven, you may extend one or more levelers to attain a level, stable cabinet placement. Turning the leveler
clockwise will extend the leveler; turning it counter-clockwise will retract it.
STEP 2 - Adjust Door Hinges (if needed)
The doors on your console should be evenly spaced and the doors should open and close freely without rubbing
against the door frame. If the cabinet’s doors appear out of alignment, this condition can be corrected with minor
adjustment to the European hinges on each door. Because these hinges are adjustable, adjusting one hinge
element can sometimes cause the need for adjustments to other elements. But with a few adjustments, you
can modify the orientation of the cabinet doors to make sure that they hang
perfectly within your cabinet.
Use the Phillips Screwdriver T1 supplied to adjust the door hinges:
• By adjusting Screw 1, the door will move LEFT or RIGHT within the frame.
Make minor adjustments at both top and bottom hinges for best results.
• By adjusting Screw 2, the door will move UP or DOWN.
• By adjusting Screw 3 the entire door will move IN or OUT, opening or
closing the gap between the door frame and cabinet. (This screw rarely
needs adjustment.)
Tightening screw 1
on top hinge will open the
seam between doors here.
Loosening screw 1
on this hinge will close
the seam between
doors here.
1 2 3